Paver Sealer Calculator
Gallons of paver sealer = area × (1 + waste) × coats ÷ the area one gallon covers per coat, rounded up. A 12 × 16 ft patio is 192 sq ft, or 211.2 sq ft with 10% waste. With a water-based acrylic on average concrete pavers (about 175 sq ft per gallon per coat, a typical figure) and 2 coats, that is 3 gallons. The cheapest way to buy them at typical prices is 3 × 1-gallon jugs. One coat would be 2 gallons. Makers publish wide ranges for pavers, often 100 to 225 sq ft per gallon, because porosity and joint width change how much sealer gets used, so check your can’s label: these rates are typical, not a guarantee.
Figures based on the sources listed belowUpdated How we calculate
Buy 3 gallons.
Buy 3 gallons
192 sq ft + 10% waste = 211.20 sq ft
- Pavers to seal: 192 sq ft
- Sealer needed (with waste and coats): 2.4 gal
- Cheapest containers: 3 × 1-gallon jugs (3 gal)
- Second coat: 2 coats are included, about 1.2 gal per coat; apply thin coats and let each dry per the label
- Joint sand: film-forming sealers can stiffen joint sand only if the joints are full and dry; polymeric sand gives the firmest hold, and the sealer goes on after it has cured
Low
$93.00
Expected
$135.00
High
$189.00
Includes 19.20 sq ft waste
How this number is calculated
192 sq ft + 10% waste = 211.20 sq ft ÷ 87.5 sq ft per gallon = 3 gallons
Shopping list
- Paver sealer (5 gal)
- Paver cleaner
- Polymeric sand
- Pump sprayer for sealer
- Sealer roller (3/8 in nap) and extension pole
Your project
- Patio length × patio width: 12 × 16 ft
- Sealer type: Water-based acrylic (film-forming, can lock joint sand)
- Paver porosity: Average concrete pavers
- Joints: Standard joints (rate already includes them)
- Coats: 2
- Waste: Standard (+10%)
Also pick up
- Paver sealer (5 gal)
- Paver cleaner
- Polymeric sand
- Pump sprayer for sealer
- Sealer roller (3/8 in nap) and extension pole
Reopen this calculation: /calculators/paver-sealer/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjoxMiwid2lkdGhGdCI6MTZ9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMSwicGFyYW1zIjp7InByb2R1Y3QiOjEsInBvcm9zaXR5IjoyLCJqb2ludHMiOjEsImNvYXRzIjoyfX0
Show diagram
Saved projects
No saved projects yet.
Typical paver coverage by sealer type and porosity
| Sealer type | Dense or smooth pavers (low porosity) (sq ft/gal) | Average concrete pavers (sq ft/gal) | Porous, tumbled or textured pavers (sq ft/gal) |
|---|---|---|---|
| Water-based acrylic | 250 | 175 | 125 |
| Solvent-based acrylic | 200 | 175 | 125 |
| Penetrating silane/siloxane | 200 | 150 | 100 |
How much sealer for common paver areas
| Area | Area with waste (sq ft) | Water-based acrylic, 2 coats | Solvent-based acrylic, 2 coats | Penetrating, 1 coat |
|---|---|---|---|---|
| 10 × 10 ft patio | 110 | 2 gal (2 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) | 1 gal (1 × 1-gallon jug) |
| 12 × 16 ft patio | 211.2 | 3 gal (3 × 1-gallon jugs) | 3 gal (3 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) |
| 4 × 20 ft walkway | 88 | 2 gal (2 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) | 1 gal (1 × 1-gallon jug) |
| 20 × 20 ft patio | 440 | 6 gal (1 × 5-gallon pail + 1 × 1-gallon jug) | 6 gal (1 × 5-gallon pail + 1 × 1-gallon jug) | 3 gal (3 × 1-gallon jugs) |
| 12 × 24 ft driveway apron | 316.8 | 4 gal (1 × 5-gallon pail) | 4 gal (1 × 5-gallon pail) | 3 gal (3 × 1-gallon jugs) |
| 20 × 24 ft paver driveway | 528 | 7 gal (1 × 5-gallon pail + 2 × 1-gallon jugs) | 7 gal (1 × 5-gallon pail + 2 × 1-gallon jugs) | 4 gal (4 × 1-gallon jugs) |
Methodology & assumptions
Paver area is length times width, less any area you will not seal. The area is multiplied by 1 plus the waste allowance (0%, 10% or 20%) and by the number of coats, then divided by the square feet one gallon covers in a single coat, and rounded up to whole gallons. The coverage per coat comes from the sealer type and the paver porosity (dense or smooth pavers (low porosity), average concrete pavers, porous, tumbled or textured pavers). The values are typical figures chosen inside the ranges makers publish for pavers: Alliance Gator lists about 100 to 225 sq ft per gallon for its Gator Hybrid Seal and about 175 for Gator Seal Satin Look; retailer listings of SEK’s Surebond SB-1300 give 80 to 120 with joint stabilizing and 150 to 300 without, and Western Interlock lists 100 to 200 for concrete pavers; Seal-Krete’s Original sealer lists 80 to 300 for a single coat; Behr’s Premium Wet-Look Sealer lists 200 to 450; penetrating paver sealers list about 100 to 200. Makers’ rates already include normal joints. The dense, average and porous values within those ranges, the 20% cut for wide or deep joints (a rate of 0.8 times the normal one), the waste percentages and the shelf prices are rules of thumb and estimates, not published rates. The same rate is used for every coat; Seal-Krete lists a second coat as covering about 50% more, so a second coat may use a little less than shown. These rates agree with the broader concrete sealer calculator, whose paver sealer row (150 and 125 sq ft per gallon) lies inside the same ranges. Containers: the gallons are rounded up, then every mix of 5-gallon pails and 1-gallon jugs that holds at least that many is priced and the cheapest is shown (ties go to fewer containers). Drying, recoat and cure times differ by product and are not calculated; use your label. The metric toggle shows lengths in m and areas in m²; sealer still comes in the US container sizes.
- Alliance Gator, Gator Hybrid Seal Low Gloss technical data sheet (July 2025) and High Gloss with Color Enhancer data sheet: about 100-225 sq ft/gal, varying with joint size and paver porosity; 40-85°F application, no rain for 24 hours
- Alliance Gator, Gator Seal Signature Series (Natural Look) and Satin Look sealer pages: 1 US gal covers about 175 sq ft, approximate and varying with porosity and joint width
- SEK Surebond, SB-1300 Joint Stabilizing Sealer, as listed by Lurveys and Western Interlock: 80-120 sq ft/gal with joint stabilizing, 150-300 without; 100-200 on concrete pavers
- Seal-Krete (Rust-Oleum), Original sealer technical data sheet: 80-300 sq ft/gal single coat by porosity, second coat about 50% greater coverage
- Behr, BEHR PREMIUM Wet-Look Sealer product page and how-to guide: spread rate 200-450 sq ft/gal, pavers listed, thin coats up to four, 50-80°F
- Radon Seal, PaverArmor Penetrating Paver Sealer product data sheet: about 100-200 sq ft/gal on pavers, depending on porosity
- Techniseal, WL4 Wet Look Sealer data sheet (paver sealer): up to 150 sq ft/gal; SRW paver sealer data sheets: 150-200 sq ft/gal (also cited on the concrete sealer calculator)
- Typical US shelf prices for 1-gallon and 5-gallon paver sealer containers (estimate)
How to calculate how much paver sealer you need
- Measure the paver area. Measure the length and width of the patio, walkway or driveway in feet and multiply them. Subtract any area you will not seal.
- Pick the sealer type and porosity. Choose water-based acrylic, solvent-based acrylic or penetrating silane/siloxane, then dense, average or porous pavers. Compare the coverage on your can with the table.
- Set the joints and coats. Choose wide or deep joints if the sealer should lock the sand. Enter the number of coats the label calls for: penetrating sealers are usually one, film-forming sealers usually two thin coats.
- Add waste. Add 10% for edges, spills and roller loss, or 20% for very porous pavers or spraying.
- Divide and round up. Multiply the area with waste by the coats, divide by the square feet one gallon covers per coat, round up, then buy the cheapest mix of 5-gallon pails and 1-gallon jugs.
Worked examples
| Project | Result |
|---|---|
| 12 × 16 ft patio, water-based acrylic, average pavers, 2 coats, 10% waste | 192 sq ft + 10% waste ≈ 211 sq ft → 3 gallons |
| 12 × 16 ft patio, water-based acrylic, average pavers, wide joints, 2 coats, 10% waste | 192 sq ft + 10% waste ≈ 211 sq ft → 4 gallons |
| 20 × 24 ft paver driveway, solvent-based acrylic, average pavers, 2 coats, 10% waste | 480 sq ft + 10% waste ≈ 528 sq ft → 7 gallons |
| 10 × 10 ft paver patio, penetrating sealer, porous pavers, 1 coat, 20% waste | 100 sq ft + 20% waste ≈ 120 sq ft → 2 gallons |
Frequently asked questions
- How much sealer do I need for a paver patio?
- A 12 × 16 ft patio is 192 sq ft, or 211.2 sq ft with 10% waste. At about 175 sq ft per gallon per coat for a water-based acrylic on average pavers, two coats take 2.4 gallons, so buy 3. Change the sealer type, porosity and coats in the calculator to see yours. For a poured concrete driveway or slab, use the concrete sealer calculator.
- How many square feet does a gallon of paver sealer cover?
- It depends on the sealer, the pavers and the joints. Alliance Gator’s Gator Hybrid Seal data sheets list about 100 to 225 sq ft per gallon and say the figure varies with joint size and paver porosity, and its Gator Seal Satin Look is listed at about 175. Retailer listings of SEK’s Surebond SB-1300 joint stabilizing sealer give 80 to 120 sq ft per gallon when stabilizing joints and 150 to 300 without. Seal-Krete’s Original sealer lists 80 to 300 for a single coat depending on porosity, and Behr’s Premium Wet-Look Sealer, which lists pavers among its surfaces, gives 200 to 450. Penetrating paver sealers run about 100 to 200. The table above has the single-coat values the calculator uses.
- Is the coverage on the can per coat or for two coats?
- Treat it as one coat unless the label says otherwise. Seal-Krete’s data sheet gives its range as a single coat and says a second coat covers about 50% more area because the first coat has filled the pores. This calculator keeps the same rate for every coat, which is the safe side: it may leave you a little sealer over, not short. If your label says its rate is for two coats, enter 1 coat and use that rate.
- Should I apply one coat or two?
- Follow the label. Film-forming acrylics are usually applied as two thin coats rather than one heavy one, which can turn cloudy or milky. Behr’s wet-look sealer says to apply a thin coat, not let it pool, and allows up to four coats for more gloss. Penetrating silane/siloxane sealers are usually one saturating application. Each extra coat needs the full gallons again, which is why the calculator multiplies by coats.
- Will sealer lock the joint sand?
- Some will. Joint stabilizing sealers such as SEK’s Surebond SB-1300 and Alliance Gator’s Hybrid Seal are made to soak into the sand and bind it, as well as coat the paver surface. Penetrating silane/siloxane sealers do not form a film, so they do not lock the sand. Whatever you use, the joints must be full, clean and dry, and polymeric sand must have cured first. Sealing over wet or loose sand can trap moisture and leave a hazy surface. Wide or deep joints soak up more, so the calculator offers a wide-joint setting that cuts the coverage by 20%, an estimate.
- How long after installing pavers should I wait to seal?
- Alliance Gator’s sheets say pavers are usually sealed about 60 days after installation, though they ask you to follow the latest data sheet for the product. Many makers also ask for 50 to 80°F (Behr) or 40 to 85°F (Alliance Gator) air and surface temperatures, dry pavers, and no rain for 24 hours. These are the makers’ numbers for those products; use your label’s.
- Why do porous or tumbled pavers need more?
- Rough, tumbled or open-textured pavers have more surface and more pores to soak up sealer, so a gallon covers less. Dense, smooth pavers absorb little and let the sealer spread further. Behr’s Canadian product pages say the spread rate is highly dependent on surface roughness and porosity. Try a small test patch: if the first coat soaks in at once, plan on the porous rate.
- How are the containers chosen?
- After rounding the paver sealer up to whole gallons, the calculator compares every combination of 5-gallon pails and 1-gallon jugs that covers it and picks the lowest total. Because a pail is cheaper per gallon, one pail can beat four jugs even with sealer left over. The prices are typical shelf prices for each sealer type, an estimate, so if your store’s prices differ the cheapest mix may too.