Concrete Stain Calculator
Gallons of stain = area × (1 + waste) × coats ÷ the area one gallon covers per coat, rounded up. A 20 × 20 ft patio or garage floor is 400 sq ft, or 440 sq ft with 10% waste. With a semi-transparent concrete stain on an average broom-finished slab (about 300 sq ft per gallon per coat, a typical figure) and 2 coats, that is 3 gallons. One coat would be 2 gallons. An acid or reactive stain at the same size takes 3 gallons and needs a neutralizing rinse before the sealer. Coverage depends on the product and how porous the concrete is, so check your can’s label: these rates are typical, not a guarantee.
Figures based on the sources listed belowUpdated How we calculate
Buy 3 gallons.
Buy 3 gallons
400 sq ft + 10% waste = 440.00 sq ft
- Surface to stain: 400 sq ft
- Stain needed (with waste and coats): 2.9 gal
- Cheapest containers: 3 × 1-gallon jugs (3 gal)
- Neutralizer or cleaner: No neutralizer for this type; clean and degrease the slab, rinse and let it dry, and follow the label for etching and cure time
- Sealer to finish: about 3.5 gal of water-based acrylic, 2 coats (1 × 5-gallon pail); see the concrete sealer calculator for other types
Low
$84.00
Expected
$120.00
High
$168.00
Includes 40.00 sq ft waste
How this number is calculated
400 sq ft + 10% waste = 440.00 sq ft ÷ 150 sq ft per gallon = 3 gallons
Shopping list
- Acid concrete stain kit
- Semi-transparent concrete stain (1 gal)
- Acid-resistant pump sprayer
- Concrete cleaner or degreaser
- Concrete sealer (5 gal)
Your project
- Length × width: 20 × 20 ft
- Stain type: Semi-transparent concrete stain
- Surface: Broom-finished or average
- Coats: 2
- Waste: Standard (+10%)
Also pick up
- Acid concrete stain kit
- Semi-transparent concrete stain (1 gal)
- Acid-resistant pump sprayer
- Concrete cleaner or degreaser
- Concrete sealer (5 gal)
Reopen this calculation: /calculators/concrete-stain/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjoyMCwid2lkdGhGdCI6MjB9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMSwicGFyYW1zIjp7InByb2R1Y3QiOjMsImZpbmlzaCI6MiwiY29hdHMiOjJ9fQ
Show diagram
Saved projects
No saved projects yet.
Typical coverage by stain type and surface
| Stain type | Smooth or dense (sq ft/gal) | Broom-finished (sq ft/gal) | Porous or rough (sq ft/gal) |
|---|---|---|---|
| Acid or reactive stain | 400 | 325 | 250 |
| Water-based penetrating stain | 400 | 300 | 200 |
| Semi-transparent concrete stain | 400 | 300 | 200 |
| Solid-color concrete stain | 550 | 450 | 400 |
How much stain for common surfaces
| Surface | Area with waste (sq ft) | Acid or reactive | Water-based penetrating | Semi-transparent | Solid color |
|---|---|---|---|---|---|
| 10 × 10 ft patio | 110 | 1 gal (1 × 1-gallon jug) | 1 gal (1 × 1-gallon jug) | 1 gal (1 × 1-gallon jug) | 1 gal (1 × 1-gallon jug) |
| 12 × 16 ft patio | 211.2 | 2 gal (2 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) | 1 gal (1 × 1-gallon jug) |
| 20 × 20 ft two-car garage floor | 440 | 3 gal (3 × 1-gallon jugs) | 3 gal (3 × 1-gallon jugs) | 3 gal (3 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) |
| 10 × 30 ft single driveway | 330 | 3 gal (3 × 1-gallon jugs) | 3 gal (3 × 1-gallon jugs) | 3 gal (3 × 1-gallon jugs) | 2 gal (2 × 1-gallon jugs) |
| 20 × 24 ft double driveway | 528 | 4 gal (4 × 1-gallon jugs) | 4 gal (4 × 1-gallon jugs) | 4 gal (4 × 1-gallon jugs) | 3 gal (3 × 1-gallon jugs) |
| 30 × 40 ft basement or shop slab | 1,320 | 9 gal (1 × 5-gallon pail + 4 × 1-gallon jugs) | 9 gal (1 × 5-gallon pail + 4 × 1-gallon jugs) | 9 gal (1 × 5-gallon pail + 4 × 1-gallon jugs) | 6 gal (1 × 5-gallon pail + 1 × 1-gallon jug) |
Methodology & assumptions
Surface area is length times width, less any area you will not stain. The area is multiplied by 1 plus the waste allowance (0%, 10% or 20%) and by the number of coats, divided by the square feet one gallon covers in a single coat, and rounded up to whole gallons. The coverage per coat comes from the stain type and surface (smooth, troweled or dense, broom-finished or average, porous, rough or old). The values are typical figures chosen inside the ranges makers publish: Behr lists 250 to 500 sq ft per gallon by roller for its semi-transparent concrete stain and 400 to 600 for its solid-color concrete stain, Rust-Oleum lists 250 to 400 on smooth and 175 to 200 on rough concrete for its RockSolid semi-transparent stain, and Quikrete lists 200 to 400 for its penetrating stain. Acid-stain makers publish less: Direct Colors lists about 200 sq ft per gallon for its two-coat EverStain system and 150 to 200 for its gel stain, so the per-coat acid figures here are an estimate set to land near that when you apply two coats. The broom-finished column, the waste percentages and the container prices are rules of thumb and estimates, not published rates. Neutralizer: one gallon of mixed solution (4 oz of concentrate per gallon of water, per the Direct Colors data sheet) is counted for every 200 sq ft of surface, rounded up, for acid and reactive stains only. Sealer: the sealer line uses the concrete sealer calculator’s water-based acrylic rate for the same surface, two coats, the same waste and the same pail and jug packing, so the figures agree between the two pages; a different sealer type changes it, so use that calculator. Drying, reaction and recoat times differ by product and are not calculated. The metric toggle shows lengths in m and areas in m²; stain and sealer still come in US container sizes.
- Behr, BEHR PREMIUM Semi-Transparent Decorative Concrete Stain product page: roller 250-500 sq ft/gal; spray base coat 175-250, accent coat 350-500
- Behr, BEHR PREMIUM Solid Color Concrete Stain product page: 400-600 sq ft/gal (rough 400-500, smooth 500-600); two coats may be needed; recoat 2-4 hours
- Rust-Oleum, RockSolid Semi-Transparent Concrete Stain product listings: 250-400 sq ft/gal smooth, 175-200 rough or porous (retailer listings of the label differ)
- Quikrete, Penetrating Concrete Stain data sheet (7215-15 to 7215-18): 200-400 sq ft/gal, 28-day cure, 50-90°F, recoat after dry to touch
- Direct Colors, EverStain 3-Step Acid Stain System product and specification pages: about 200 sq ft/gal (2 coats); DecoGel color chart: 150-200 sq ft/gal
- Direct Colors, ProClean Neutralizer technical data sheet: 4 oz concentrate per gallon of water covers about 200 sq ft
- Sika Scofield, Lithochrome Chemstain Classic product data sheet and retailer notes on neutralizing with baking soda in water (acid-stain coverage is not given as one number; rule of thumb for undiluted acid stain is 200-400 sq ft/gal)
- Kemiko, Stone Tone and Rembrandt stain product listings: retailer and trade-catalog coverage figures disagree (150-800 sq ft/gal depending on dilution), so none is used directly; check the label
- Concrete sealer calculator on this site: water-based acrylic rates, two coats and pail/jug packing reused for the sealer step
- Typical US shelf prices for 1-gallon and 5-gallon concrete stain containers (estimate)
How to calculate how much concrete stain you need
- Measure the surface. Measure the length and width in feet and multiply them. Subtract any area you will not stain.
- Pick the stain type and surface. Choose acid or reactive, water-based penetrating, semi-transparent or solid-color stain, then smooth, broom-finished or porous. Compare the coverage on your can with the table.
- Set the coats. Enter the number of coats the label calls for; two is common for even color.
- Add waste. Add 10% for edges, spills and uneven absorption, or 20% for very porous concrete or spraying.
- Divide, round up, then plan neutralizer and sealer. Multiply the area with waste by the coats, divide by the square feet one gallon covers per coat and round up. For acid stain add the neutralizing rinse, and add the sealer shown under the result.
Worked examples
| Project | Result |
|---|---|
| 20 × 20 ft patio, semi-transparent stain, broom finish, 2 coats, 10% waste | 400 sq ft + 10% waste ≈ 440 sq ft → 3 gallons |
| 12 × 16 ft patio, acid stain, broom finish, 2 coats, 10% waste | 192 sq ft + 10% waste ≈ 211 sq ft → 2 gallons |
| 20 × 24 ft double driveway, solid-color stain, porous, 2 coats, 10% waste | 480 sq ft + 10% waste ≈ 528 sq ft → 3 gallons |
| 10 × 30 ft driveway, water-based penetrating stain, smooth, 1 coat, 0% waste | 300 sq ft → 1 gallon |
Frequently asked questions
- How much concrete stain do I need for a patio?
- A 20 × 20 ft patio is 400 sq ft, or 440 sq ft with 10% waste. At about 300 sq ft per gallon per coat for a semi-transparent stain on broom-finished concrete, two coats take 2.9 gallons, so buy 3. Change the stain type, surface and coats in the calculator to see yours.
- How many square feet does a gallon of concrete stain cover?
- It depends on the stain and the concrete. Behr’s Premium Semi-Transparent Decorative Concrete Stain lists 250 to 500 sq ft per gallon by roller (175 to 250 for a sprayed base coat), and its Solid Color Concrete Stain lists 400 to 600, with two coats often needed for even color. Rust-Oleum’s RockSolid semi-transparent stain lists 250 to 400 on smooth concrete and 175 to 200 on rough. Quikrete’s penetrating stain lists 200 to 400. Direct Colors’ EverStain acid stain lists about 200 sq ft per gallon for its two-coat system. The table above has the per-coat values the calculator uses.
- Do I need to neutralize concrete stain?
- Acid or reactive stains do: after the stain reacts for the time on the label (Direct Colors lists roughly 4 to 6 hours), the leftover acid and residue must be neutralized and rinsed off before sealing, or the sealer can lose adhesion. A neutralizer concentrate mixed at 4 oz per gallon of water covers about 200 sq ft per gallon of solution, according to Direct Colors’ data sheet; baking soda in water is a common alternative, and the calculator shows the gallons of solution. Water-based, semi-transparent and solid stains are not acid-based, so they need a clean, degreased, dry slab instead; follow the label.
- Do I have to seal stained concrete?
- Acid and other penetrating stains only color the concrete and are normally sealed for protection and depth of color. Acrylic-based semi-transparent and solid stains are often sold as a color coat, and many makers still recommend a sealer in traffic areas. The calculator adds a sealer line using the same water-based acrylic rates, two coats and container packing as the concrete sealer calculator, so the two pages agree: about 3.5 gal of water-based acrylic, 2 coats (1 × 5-gallon pail) for the 20 × 20 ft default. Use your stain maker’s recommended sealer.
- Should I apply one coat or two?
- Follow the label. Behr says that because concrete varies in texture and porosity, two coats may be needed for uniform color, and recoat after about 2 to 4 hours. Quikrete’s penetrating stain allows a second coat one hour after the first is dry to the touch. Acid stains are often applied in two thin coats for depth of color. Each coat needs the full gallons again, which is why the calculator multiplies by coats.
- Why does porous or old concrete need more stain?
- Rough, open or weathered concrete has more surface and more pores to absorb stain, so a gallon covers less; makers list a lower coverage for rough surfaces. Smooth, troweled concrete is dense and absorbs less, though very dense slabs may reject some stains unless the surface is opened by etching or grinding. A small test patch tells you which column of the table to use.
- How are the containers chosen?
- The calculator rounds your gallons up and then tries every mix of 5-gallon pails and 1-gallon jugs that holds at least that much, using the same packing helper as the concrete sealer calculator, and shows the cheapest. The prices are typical shelf prices, an estimate, so if your store’s prices differ the cheapest mix may too. Some stains are sold only in gallon sizes.
- Can I stain new concrete right away?
- No. Quikrete’s data sheet for its penetrating stain calls for 28 days of cure before application and temperatures between 50 and 90°F. Acid stains also need the slab clean and free of sealers, curing compounds and grease. Cure and prep rules are the maker’s, so use your label.