Skip to main content
ponderloop

Flagstone Calculator: How Many Tons Do I Need?

A 15 × 12 ft patio (180 sq ft) of 1.5 to 2 inch flagstone needs about 3 tons (2.23 tons exact) with 10% joints and 10% extra for cuts. Under it, a 1 inch sand setting bed is 0.61 cu yd (about 0.83 tons) and a 4 inch gravel base is 2.44 cu yd (about 3.42 tons). Stone yards quote coverage as a range, about 70 to 90 sq ft of stone per ton at this thickness, so confirm with your supplier.

Figures based on the sources listed belowUpdated How we calculate

Extra stone for cuts and breakage
Thicker stone weighs more per square foot, so a ton covers less. The coverage used is the middle of the range stone yards publish for that thickness (typical, not a guarantee).
Open joints between stones are area you do not need stone for. The percentages are our planning estimates for irregular flagstone, not published figures.

If your stone yard quotes sq ft per ton for the exact stone and thickness, type it here and it replaces the typical range.

Extra area on top of length × width. Areas to leave out, such as pavers set into the patio, go under “Add area to leave out”.

About 1 in of coarse sand or stone dust is typical under dry-laid flagstone. Enter 0 to leave sand out.

About 4 in of compacted crushed stone is typical for a patio or walk; more over soft soil or in frost areas. Enter 0 if laying on an existing slab or mortar bed.

Buy 3 tons.

Buy 3 tons

180 sq ft + 10% waste = 198.00 sq ft

  • Flagstone to order (exact): 2.23 tons, waste included
  • Coverage used: 80 sq ft of stone per ton (typical 70–90 at 1.5–2 in), 89 sq ft of finished area per ton after joints
  • Setting sand: 0.61 cu yd (≈ 0.83 tons)
  • Gravel base: 2.44 cu yd (≈ 3.42 tons)

Low

$600.00

Expected

$1,050.00

High

$1,650.00

Includes 18.00 sq ft waste

How this number is calculated

180 sq ft + 10% waste = 198.00 sq ft ÷ 88.89 sq ft per ton = 3 tons

Next step in your project

  • Gravel Calculator

    The compacted gravel base under the stone, by depth. Opens with your 15 × 12 ft filled in.

  • Paver Sand Calculator

    The sand setting bed, in bags or bulk. Opens with your 15 × 12 ft filled in.

Shopping list

  • Plate compactor
  • Masonry chisel and hammer set
  • Angle grinder with diamond blade
  • Rubber mallet
  • Polymeric sand (for joints)
  • Landscape fabric
Show diagram

Saved projects

No saved projects yet.

Flagstone coverage per ton by thickness (typical)

Square feet of laid stone per ton as stone yards publish it: ranges, because density, cut and thickness vary by quarry. “Used here” is the middle of the range. The last two columns are worked by the calculator for 100 sq ft of finished patio with 10% joints and no waste.
ThicknessTypical sq ft per tonUsed hereSq ft of patio per tonTons per 100 sq ft of patio
1–1.5 in90–1101001110.9
1.5–2 in70–9080891.13
2–3 in60–7065721.38

Tons of flagstone by patio size and thickness

Order quantities in tons, rounded up to a whole ton, with 10% joints and 10% waste, using the middle of each coverage range. Each cell is the calculator’s answer for that size.
Patio sizeAreaThin (1–1.5 in)Patio (1.5–2 in)Steppers (2–3 in)
8 × 10 ft80 sq ft1 (0.79)1 (0.99)2 (1.22)
10 × 10 ft100 sq ft1 (0.99)2 (1.24)2 (1.52)
12 × 12 ft144 sq ft2 (1.43)2 (1.78)3 (2.19)
15 × 12 ft180 sq ft2 (1.78)3 (2.23)3 (2.74)
16 × 20 ft320 sq ft4 (3.17)4 (3.96)5 (4.87)
20 × 20 ft400 sq ft4 (3.96)5 (4.95)7 (6.09)

Setting bed per 100 sq ft by depth

Cubic yards with a 10% allowance for spill and compaction, and tons at 1.4 tons per cu yd for crushed-stone gravel and 1.35 for sand (the same planning densities the gravel and sand calculators use).
LayerDepthCu yd per 100 sq ftTons per 100 sq ft
Sand1 in0.340.46
Sand2 in0.680.92
Gravel base4 in1.361.9
Gravel base6 in2.042.85
Gravel base8 in2.723.8

Methodology & assumptions

Area is length × width plus any add-on area (a landing, steps or a border), less any area you leave out, in square feet. A waste percentage is added for cuts and breakage: 5% for squared or sawn stone, 10% for irregular flagstone and 15% for heavy cutting or a set pattern. Stone yards sell flagstone by weight and publish how many square feet of laid stone a ton covers for each thickness, as a range; the calculator uses the middle of the range for the thickness class you pick (about 100 sq ft per ton at 1 to 1.5 in, 80 at 1.5 to 2 in and 65 at 2 to 3 in), or your supplier’s own figure if you type one. Those figures count stone surface, so open joints are subtracted: a ton covers the stone figure ÷ (1 − joint share) square feet of finished area, with the joint share set at 0, 5, 10 or 20% of the area. That joint share is a planning estimate, not a published number, as are the waste percentages. Tons = area with waste ÷ finished sq ft per ton, rounded up to a whole ton for the order, with the exact tons shown too. The setting bed is area × depth (1 in of sand and 4 in of gravel by default), plus 10% for spill and compaction, in cubic yards (÷ 27), and converted to tons with the same planning densities as the gravel and sand calculators (about 1.4 and 1.35 tons per cubic yard). Real coverage varies with the stone: density differs between sandstone, limestone and bluestone, and cut and thickness vary within a pallet. A supplier’s figure for the actual stone beats any typical range.

How to calculate how much flagstone you need

  1. Measure the area. Enter the patio or path length and width in feet. Add any landing or border under add-on area, and add areas to leave out, such as a bed or pavers set into the patio.
  2. Pick the stone thickness. Choose thin (1 to 1.5 in), patio (1.5 to 2 in) or steppers (2 to 3 in). If your stone yard quotes square feet per ton for your stone, type it in to replace the typical range.
  3. Set the joints and waste. Choose the joint width you plan and the extra for cuts and breakage: 10% for irregular flagstone.
  4. Check the setting bed. Leave 1 inch of sand and 4 inches of gravel, or change the depths. Enter 0 to leave a layer out.
  5. Order by the ton. The result is whole tons of flagstone, with the exact tons, the sand and the gravel in cubic yards and tons underneath. Compare it with your supplier’s quote.

Worked examples

ProjectResult
15 × 12 ft patio, 1.5–2 in flagstone, 1 in joints, 10% waste3 tons (2.23 tons exact), 0.61 cu yd sand and 2.44 cu yd gravel
10 × 10 ft patio of thin 1–1.5 in stone, 5% joints, 10% waste2 tons (1.05 tons exact), 0.34 cu yd sand and 1.36 cu yd gravel
3 × 30 ft path, 1.5–2 in stone, 10% joints, 15% waste for cutting, 2 in gravel only2 tons (1.16 tons exact), 0.61 cu yd gravel
12 × 16 ft patio with a 4 × 4 ft bed left out, steppers, 20% joints, 10% waste3 tons (2.38 tons exact), 0.6 cu yd sand and 2.39 cu yd gravel
12 × 12 ft patio plus a 20 sq ft landing, supplier says 75 sq ft per ton3 tons (2.16 tons exact), 0.56 cu yd sand and 2.23 cu yd gravel

Frequently asked questions

How many tons of flagstone do I need for a patio?
Divide the patio area plus 10% waste by the square feet a ton covers. For 1.5 to 2 inch stone that is about 80 sq ft of stone per ton, or about 89 sq ft of finished patio per ton once 10% of the area is open joints. A 15 × 12 ft patio is 180 sq ft, 198 sq ft with waste, which is 2.23 tons, so order 3.
How many square feet does a ton of flagstone cover?
It depends on thickness. Stone yards publish roughly 90 to 110 sq ft per ton for thin stone around 1 to 1.5 inches, 70 to 90 at 1.5 to 2 inches, and 60 to 70 for 2 to 3 inch steppers. Select Stone’s 2013 guide, Krukowski’s Sandy Creek sheet and County Materials give figures in these bands. These are typical ranges, not guarantees: ask your yard for the exact stone.
Why do the numbers differ from the “200 sq ft per ton at 1 inch” you see online?
That figure comes from weight alone (2,000 lb of stone at about 150 lb per cubic foot, spread 1 inch thick). Real flagstone is irregular and uneven in thickness, a pallet’s “1 inch” stone averages thicker than 1 inch, and the stone yard’s coverage includes the joints and the rough edges. Stone-yard figures are about half of the theoretical ones, and they are the ones to order by.
What does the joint allowance do?
Supplier coverage counts the stone surface itself. If your patio has 1 inch joints, roughly 10% of its area is gap, so you need about 10% less stone than the area suggests. The calculator divides the stone coverage by (1 − joint share). The 0, 5, 10 and 20% choices are our planning estimates for irregular flagstone; a tight, closely cut fit is near 5%, a planted path near 20%.
How much sand and gravel go under flagstone?
A common dry-laid patio is a compacted gravel base of about 4 inches under a 1 inch sand setting bed; more gravel over soft soil or in frost country. For 180 sq ft the calculator gives 2.44 cu yd of gravel (about 3.42 tons) and 0.61 cu yd of sand (about 0.83 tons), each with 10% extra for spill and compaction. These depths are typical practice, not a code requirement: follow your stone supplier’s or installer’s advice.
Do I need sand on top of the gravel?
Many installers set irregular flagstone in 1 inch of coarse sand or stone dust over the gravel so each stone can be bedded level, and some set it straight on the gravel. Set the sand depth to 0 to leave it out. If you are laying on an existing slab with mortar, set both depths to 0.
How much extra flagstone should I order?
Ten percent is a common allowance for irregular flagstone, because pieces get broken or cut to fit. Use 15% for a set pattern or lots of cutting and 5% for squared or sawn stone. These are planning estimates, not published standards.
How do I figure stepping stones or a path with gaps?
For a path of stones set well apart, enter the area of the stones themselves, not the whole path, and pick the 0% joint choice. Or measure the whole path and choose the 20% wide-joint choice. Steppers are 2 to 3 inches thick and cover the least per ton.
What does flagstone cost per ton?
The price band here ($200 to $550 per ton, $350 expected) is a planning estimate based on a 2025 HomeAdvisor range of about $200 to $550 per ton. Local stone is cheaper than shipped stone, and bluestone costs more than most. Type your quote in the price box to use it instead.

Handy tools

  • Slope Calculator: Patios and walks need a fall of about 1/4 inch per foot for drainage: turn that into the drop over your run.
  • Feet and Inches Calculator: Add up measured lengths in feet and inches and get the decimal feet the fields take.

Related calculators