Boulder Weight Calculator: How Much Does a Landscape Boulder Weigh?
A granite boulder 36 × 24 × 18 inches, irregular in shape so that it fills 0.6 of its bounding box, weighs about 893 lb (0.45 tons, 405 kg). That is 36 × 24 × 18 in = 9 cubic feet of box, times 0.6 = 5.4 cubic feet of stone, times granite's 165 pounds per cubic foot. It is an estimate: a rounded stone of the same size would be nearer 780 lb (0.39 tons, 354 kg), a squared block 1,489 lb (0.74 tons, 675 kg), and the same shape in sandstone 775 lb (0.39 tons, 352 kg). For one boulder this size, a rule of thumb (an estimate) says a team with a pry bar and rollers or a ramp, or a skid steer or small tractor with a chain or strap. Enter the three dimensions, the shape and the stone.
Figures based on the sources listed belowUpdated How we calculate
893 lb (0.45 tons, 405 kg).
893 lb (0.45 tons, 405 kg)
- Weight of the boulder: 893 lb (0.45 tons, 405 kg)
- Stone volume: 5.4 cu ft per boulder (0.6 of the 9 cu ft box)
- Density used: 165.4 lb per cu ft (granite, specific gravity 2.65, typical range 2.6 to 2.8)
- Moving it (rule of thumb, estimate): at 893 lb each: a team with a pry bar and rollers or a ramp, or a skid steer or small tractor with a chain or strap. Check a machine's own rated capacity: this rule of thumb is not a lift plan
Shopping list
- Lifting straps for moving heavy objects
- Pry bar (wrecking bar)
- Heavy-duty hand truck
- Rock moving dolly
- Work gloves
- Steel-toe work boots
- Tape measure
Your project
- Boulder length (longest side) × boulder width: 36 × 24 in
- Boulder height: 18 in
- Shape: Irregular (a share of the box, estimate)
- Share of the box the stone fills: 0.6
- Stone type: Granite (specific gravity 2.65, about 165 lb per cu ft)
- Your own density, if you know it: 0 lb per cu ft
- Number of boulders (all the same size): 1
Also pick up
- Lifting straps for moving heavy objects
- Pry bar (wrecking bar)
- Heavy-duty hand truck
- Rock moving dolly
- Work gloves
- Steel-toe work boots
- Tape measure
Reopen this calculation: /calculators/boulder-weight/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjozLCJ3aWR0aEZ0IjoyfSwiZGVkdWN0aW9ucyI6W10sIndhc3RlUGN0IjowLjEsInBhcmFtcyI6eyJoZWlnaHRJbiI6MTgsImJvdWxkZXJTaGFwZSI6MiwiZmlsbEZhY3RvciI6MC42LCJzdG9uZVR5cGUiOjAsImRlbnNpdHlMYlBlckN1RnQiOjAsImJvdWxkZXJDb3VudCI6MX19
Show diagram
Saved projects
No saved projects yet.
Density of common landscape stones (typical)
| Stone | Typical range (SG) | Value used (SG) | lb per cu ft | kg per cu m | US tons per cu yd (solid) |
|---|---|---|---|---|---|
| Granite | 2.6 to 2.8 | 2.65 | 165 | 2,650 | 2.23 |
| Limestone | 2.2 to 2.7 | 2.4 | 150 | 2,400 | 2.02 |
| Sandstone | 2.0 to 2.6 | 2.3 | 144 | 2,300 | 1.94 |
| Basalt | 2.8 to 3.0 | 2.9 | 181 | 2,900 | 2.44 |
| Marble | 2.6 to 2.8 | 2.7 | 169 | 2,700 | 2.28 |
| Fieldstone (mixed, typical) | 2.4 to 2.8 | 2.6 | 162 | 2,600 | 2.19 |
Granite boulder weight by size and shape (pounds)
| Size (in) | Stone, irregular (cu ft) | Ellipsoid (lb) | Irregular, 0.6 (lb) | Box (lb) |
|---|---|---|---|---|
| 12 × 10 × 8 | 0.33 | 48 | 55 | 92 |
| 18 × 12 × 10 | 0.75 | 108 | 124 | 207 |
| 24 × 18 × 12 | 1.8 | 260 | 298 | 496 |
| 30 × 24 × 18 | 4.5 | 650 | 744 | 1,241 |
| 36 × 24 × 18 | 5.4 | 780 | 893 | 1,489 |
| 48 × 30 × 20 | 10 | 1,444 | 1,654 | 2,757 |
| 60 × 36 × 24 | 18 | 2,599 | 2,978 | 4,963 |
| 72 × 48 × 36 | 43.2 | 6,237 | 7,147 | 11,911 |
The same 36 × 24 × 18 in boulder in each stone
| Stone | Weight (lb) | US tons | Kilograms |
|---|---|---|---|
| Granite | 893 | 0.45 | 405 |
| Limestone | 809 | 0.4 | 367 |
| Sandstone | 775 | 0.39 | 352 |
| Basalt | 978 | 0.49 | 443 |
| Marble | 910 | 0.46 | 413 |
| Fieldstone (mixed, typical) | 876 | 0.44 | 398 |
Who or what moves it: a rule of thumb by weight of one boulder (estimate)
| One boulder (lb) | Typical help |
|---|---|
| up to 50 | one person can lift it, with a good grip and a straight back |
| 50 to 100 | two people with lifting straps or a carry sling |
| 100 to 300 | two to four people with a hand truck, a stone dolly or a wheelbarrow on planks |
| 300 to 1,000 | a team with a pry bar and rollers or a ramp, or a skid steer or small tractor with a chain or strap |
| 1,000 to 3,000 | a skid steer, compact loader or mini excavator with a lifting chain, rated well above this weight |
| over 3,000 | a larger excavator or loader, or a boom truck or crane, run by a trained operator |
Methodology & assumptions
Weight = volume of stone × density. Volume starts from the box around the boulder, length × width × height, each measured at its widest point and typed in inches (centimetres under the metric toggle), and the shape then says how much of the box the stone fills. Box: all of it (× 1), right for a squared block, a cut slab or a column. Ellipsoid: π ÷ 6 = 0.5236 of the box, the volume of an ellipsoid whose three axes are the length, width and height (4 ÷ 3 × π × half-length × half-width × half-height); a smooth, rounded boulder is close to this. Irregular: a share of the box that you set, 0.6 by default. That figure is an estimate, a planning number between the ellipsoid (0.52) and the box (1.0), not a published table: about 0.5 to 0.6 for a rounded boulder, 0.6 to 0.7 for a lumpy angular one, 0.8 or more for a flat slab or blocky stone. A boulder is usually irregular, which is why the default is between the other two shapes. For the default 36 × 24 × 18 in granite boulder that is 893 lb (0.45 tons, 405 kg) at 0.6, 744 lb (0.37 tons, 338 kg) at 0.5 and 1,489 lb (0.74 tons, 675 kg) as a box, so the choice of shape matters as much as the choice of stone: when you can, measure the stone twice, and treat the answer as good to about 15 to 25%. Density: each stone type is given as a specific gravity, the stone's dry bulk density as a multiple of water's, times water's 62.428 lb per cubic foot (1,000 kg per cubic metre). The values are typical figures in the middle of each stone's range, not measurements of your stone: granite 2.65 (165 lb per cu ft; ASTM C615 sets a minimum of 160 lb per cu ft for granite dimension stone), limestone 2.4 (ASTM C568 classes limestone as low density at 110 to 135 lb per cu ft, medium over 135 up to 160 and high over 160, and the figure used is inside the medium class), sandstone 2.3 (the widest range of the common stones, about 2.0 to 2.6, because the pore space varies), basalt 2.9 (dense basalt runs about 2.8 to 3.0; vesicular, bubbly lava rock is much lighter), marble 2.7 (ASTM C503 minimums are 162 lb per cu ft for calcite marble and 175 for dolomite marble) and fieldstone 2.6. Fieldstone is not one rock but whatever the field or quarry gave, usually granite, gneiss or sandstone, so its figure is a typical middle; a mixed load can be lighter or heavier. If a quarry or yard quotes a weight per cubic foot or ton for the stone you are buying, type it in under "Your own density": a supplier's figure beats any table. These are solid-rock densities. They are different from the bulk densities used for loose material on this site (gravel at 1.4 tons per cubic yard, about 104 lb per cu ft, and river rock at about the same), which count the air between the pieces; solid granite is 2.23 tons per cubic yard. The flagstone calculator's weight-only check uses about 150 lb per cubic foot, which sits between the limestone and sandstone values above. Water in the pores, soil on the stone and a wet surface add a little, and a boulder that is partly buried weighs all of itself, so measure the whole stone. Count: the headline is for all the boulders together, which the calculator treats as the same size; the line below it gives the weight of one. Moving it (rule of thumb, an estimate): the weight of one boulder sets the help it needs. Up to about 50 lb one person; about 100 lb two people, since 51 lb (23 kg) is the load constant in NIOSH's lifting equation, the most a worker should lift under ideal conditions with a good grip, close to the body, which a rough stone is not; then people with a hand truck, dolly or planks to about 300 lb; a team with a pry bar and rollers, or a machine, to about 1,000 lb; a skid steer, compact loader or mini excavator to about 3,000 lb; and a larger machine or a crane above that. These steps are this page's own, not a standard. For a machine, the number to check is its rated operating capacity, which for a skid steer is commonly 35 to 50% of the load that tips it, and it is lower with a heavy attachment, on soft or sloped ground, or with the load held out at full reach: stay well below it, use rated chains or slings, and keep people clear of the lift. Large boulders and anything over about a ton are a job for an operator who does it daily. Delivery and trucking weight limits are not covered here.
- ASTM C615/C615M, Standard Specification for Granite Dimension Stone: physical requirements table, minimum density 160 lb per cubic foot (2,560 kg per cubic metre), tested to C97. The granite figure on this page, 165 lb per cubic foot, is a typical value just above the minimum
- ASTM C568/C568M, Standard Specification for Limestone Dimension Stone: three density classes, low (110 to 135 lb per cubic foot), medium (over 135 up to 160) and high (over 160). The limestone value here is a typical figure in the medium class
- ASTM C503/C503M, Standard Specification for Marble Dimension Stone: minimum density 162 lb per cubic foot for calcite marble and 175 for dolomite marble (as listed in a test-laboratory summary of the standard). The marble value here, 168.6, is a typical figure for calcite marble
- ASTM C616/C616M, Standard Specification for Quartz-Based Dimension Stone: classes sandstone, quartzitic sandstone and quartzite, with density among the physical requirements. The sandstone value here is a typical figure in the middle of the commonly cited 2.0 to 2.6 range, not a value read from the standard
- McGill University Buildings, Section 31 35 00 Natural Stone (project specification): a density range of 2,160 to 2,560 kg per cubic metre (135 to 160 lb per cubic foot) for the stone it specifies, which brackets the sandstone and limestone values used here
- U.S. Geological Survey, Density of basalt core, Hilo drill hole, Hawaii: dense basalt about 2.8 to 3.1 g per cubic centimetre, with vesicular lava flows as low as 2.0, so the basalt value (2.9) is for dense basalt
- Engineering ToolBox, Minerals and other Materials: Specific Gravities (engineeringtoolbox.com): basalt 2.9 and granite 2.7, a secondary table that agrees with the values above
- U.S. Bureau of Mines, Minerals Yearbook (1953): average weights per cubic foot used to convert stone to short tons, granite 165 lb and limestone and sandstone 160 lb. An old industry conversion, higher for sandstone than the typical figure here
- NIST Handbook 44, Appendix C, General Tables of Units of Measurement: pound and kilogram (1 lb = 0.45359237 kg); the density of water is taken as 1,000 kg per cubic metre, 62.428 lb per cubic foot
- Canadian Centre for Occupational Health and Safety, NIOSH Lifting Equation: Assessing Relevant Handling Factors (ccohs.gc.ca): the load constant is 23 kg (51 lb), the weight a worker can lift under ideal conditions; real lifts are reduced from it
- SANY, Skid Loader Lift Capacity Explained: ROC vs Tipping Load & Load Weight: rated operating capacity is typically 35 to 50% of the tipping load and falls with attachments, ground and reach. Always follow the machine’s own operator’s manual and load chart
- Shape factors: the ellipsoid factor π ÷ 6 is geometry (volume of an ellipsoid ÷ the box around it). The share of the box for an irregular boulder, 0.6 by default, is this site’s estimate, not a published figure
- Loose gravel and river rock (1.4 tons per cubic yard) and the flagstone weight check (about 150 lb per cubic foot) are the figures used by the gravel, river rock and flagstone calculators on this site; solid-stone densities here are separate because a boulder has no air gaps between pieces
How to estimate the weight of a landscape boulder
- Measure the length, width and height. Measure the longest side, the widest point across it and the height, each at its widest, in inches or centimetres.
- Pick the shape. Box for a squared block or slab, Ellipsoid for a smooth rounded boulder (π ÷ 6 of the box), or Irregular and the share of the box the stone fills (about 0.6 is typical).
- Pick the stone. Choose granite, limestone, sandstone, basalt, marble or fieldstone, or type a density in lb per cubic foot if the supplier gave you one.
- Read the weight in pounds, tons and kilograms. Volume of stone × density gives the weight. For several boulders of the same size, enter how many.
- Check how to move it. The moving line suggests people or machinery for one boulder, an estimate. Check a machine’s rated capacity yourself.
Worked examples
| Project | Result |
|---|---|
| Granite, 36 × 24 × 18 in, irregular (0.6 of the box) | 893 lb (0.45 tons, 405 kg), 5.4 cu ft of stone |
| The same boulder as a smooth, rounded ellipsoid (× π ÷ 6) | 780 lb (0.39 tons, 354 kg), 4.7 cu ft of stone |
| The same size as a squared granite block (× 1) | 1,489 lb (0.74 tons, 675 kg), 9 cu ft of stone |
| Limestone, 48 × 30 × 20 in, irregular | 1,498 lb (0.75 tons, 680 kg), a skid steer, compact loader or mini excavator with a lifting chain, rated well above this weight |
| Basalt column, 12 × 12 × 48 in, as a box | 724 lb (0.36 tons, 328 kg), a team with a pry bar and rollers or a ramp, or a skid steer or small tractor with a chain or strap |
| Sandstone slab, 60 × 36 × 6 in, as a box | 1,077 lb (0.54 tons, 488 kg), 7.5 cu ft |
| Fieldstone, 18 × 12 × 10 in, irregular | 122 lb (0.06 tons, 55 kg), two to four people with a hand truck, a stone dolly or a wheelbarrow on planks |
| Four marble boulders, 30 × 24 × 20 in each | 3,371 lb (1.69 tons, 1,529 kg) in all, 843 lb (0.42 tons, 382 kg) each |
| A small accent stone, 12 × 10 × 8 in, granite | 55 lb (0.03 tons, 25 kg), two people with lifting straps or a carry sling |
Frequently asked questions
- How do I calculate the weight of a boulder?
- Measure the length, width and height at the widest points and multiply them for the box around the stone (36 × 24 × 18 in = 9 cubic feet). Multiply by the share of the box the stone fills (π ÷ 6 = 0.52 for a rounded boulder, about 0.6 for an irregular one, 1 for a squared block) to get the stone's volume, then by the stone's density in pounds per cubic foot. For granite at about 165 lb per cubic foot that is 9 × 0.6 × 165 = 893 lb, or 0.45 tons (405 kg). It is an estimate.
- What is the ellipsoid factor, π ÷ 6, and why 0.6 for irregular stones?
- An ellipsoid is a squashed sphere, and its volume is 4 ÷ 3 × π × (L ÷ 2) × (W ÷ 2) × (H ÷ 2), which is π ÷ 6 = 0.5236 of the L × W × H box. A smooth, rounded boulder is close to that. A box fills all of the box (1.0). Real landscape boulders have flatter faces and corners than an ellipsoid and less than a block, so the default of 0.6 is a planning estimate between the two (not a published figure). Use 0.5 for a very round stone, 0.7 for an angular one, 0.8 or more for a slab. At 36 × 24 × 18 in in granite those are 744 lb, 893 lb (0.6) and 1,489 lb for a full box.
- How much does a granite boulder weigh per cubic foot?
- About 165 pounds per cubic foot (specific gravity 2.65, about 2.2 tons per cubic yard of solid stone). ASTM C615 sets a minimum of 160 lb per cubic foot for granite dimension stone, and typical granite runs from about 160 to 175. Basalt is heavier (about 181), limestone and marble a little lighter or similar, sandstone the lightest of the common ones (about 144) because it is the most porous.
- Why does a boulder weigh more than the same volume of gravel?
- Loose gravel and river rock are sold by the cubic yard at about 1.4 tons per cubic yard (104 lb per cubic foot), because the air between the pieces is part of that volume. A boulder is one solid piece of rock, so the same cubic foot weighs about 165 lb in granite, roughly 60% more. The calculators do not contradict each other: the gravel, river rock and cubic-yards-to-tons figures are bulk densities of loose material, and these are solid densities. The flagstone calculator's weight check uses about 150 lb per cubic foot for solid sandstone and limestone, within the range here.
- How do I measure an irregular boulder?
- Measure the longest side as the length, the widest point at right angles to it as the width, and the height as the stone will sit (the top to the bottom, not just the part above ground if you are buying it). Measure each at its widest point, so the numbers describe the smallest box that would hold the stone. Then pick Irregular and set the share of the box it fills: lumpy stones fill less, flat or blocky ones more. If the boulder is half buried, the weight is still of the whole stone.
- How many people does it take to move a boulder?
- A rule of thumb, and only an estimate: about 50 lb or less is one person, up to about 100 lb two people with straps, up to about 300 lb two to four people with a hand truck, dolly or planks, and up to about 1,000 lb a team with a pry bar and rollers, or a machine. Above that it is a skid steer, compact loader or mini excavator, and over about 3,000 lb a larger machine or a crane. The default 893 lb granite boulder falls under: a team with a pry bar and rollers or a ramp, or a skid steer or small tractor with a chain or strap. NIOSH's lifting equation starts from a load constant of 51 lb (23 kg) for one person in ideal conditions, and a rough stone is far from ideal, so do not plan a lift near it.
- What equipment do I need for a heavy boulder?
- For a stone of several hundred pounds or more, a skid steer, compact track loader or mini excavator with a lifting chain or rated sling is the usual answer. Check the machine's rated operating capacity in its manual: for a skid steer it is commonly 35 to 50% of the tipping load and drops with a heavy attachment, soft or sloped ground and reach, so stay well under it. A boulder of 3.57 tons (the 72 × 48 × 36 in granite example, 7,147 lb) is a job for a loader with a larger rating, an excavator or a boom truck, and a trained operator. This page only estimates the weight; it cannot judge a lift.
- How accurate is the estimate?
- Expect roughly 15 to 25% either way. The shape share is the biggest unknown (0.5 versus 0.7 is a 40% difference), then the stone: sandstone and limestone vary most with their pores. For a stone you are buying, ask the supplier for the weight, which many yards measure on a scale, and for the weight per cubic foot or ton of that stone to type under "Your own density". With a known density of 150 lb per cubic foot the default boulder is 810 lb.
- How many tons is a boulder?
- Divide the pounds by 2,000 for US tons (the first figure here) or by 2,204.6 for metric tonnes. The default boulder is 0.45 tons. A boulder of roughly 4 × 3 × 2 ft irregular granite is about 1.2 tons. Boulders are often sold by the ton, so the tons figure is the one to check against a quote.
- Does stone type change the weight that much?
- Yes. The same 36 × 24 × 18 in irregular boulder is 775 lb in sandstone, 893 lb in granite and 978 lb in basalt, a swing of about 25% from lightest to heaviest. Sandstone and limestone vary most inside their own types, so if the stone type is a guess, use the sandstone and granite results as a range.
Handy tools
- Cubic Yards to Tons: Convert cubic yards of loose gravel, sand or rock into tons for a delivery order.
- Feet and Inches Calculator: Turn a boulder measured in feet and inches (3 ft 4 in) into the total inches the fields take.