Voltage Divider Calculator
With 12 V in, R1 = 10 kΩ, R2 = 6.8 kΩ, a resistor voltage divider outputs 4.857 V: Vout = Vin × R2 ÷ (R1 + R2). It draws 714.3 µA and acts like a 4.048 kΩ source, so anything the output feeds pulls the voltage down. This calculator also solves R1 or R2 for a target Vout, lists the closest standard E12, E24 or E96 resistor pairs, and adds a load in parallel with R2, with the current and the power in each resistor.
Updated Runs in your browser: nothing you enter is uploadedHow this tool works
12 V in, R1 = 10 kΩ, R2 = 6.8 kΩ
Vout = 4.857 V
- Output voltage Vout
- 4.857 V
- Ratio Vout ÷ Vin (unloaded)
- 0.4048
- Divider current (through R1)
- 714.3 µA
- Power in R1
- 5.102 mW
- Power in R2
- 3.469 mW
- Total power from the source
- 8.571 mW
- Thevenin source resistance R1‖R2
- 4.048 kΩ
The working
- Ratio = R2 ÷ (R1 + R2) = 6.8 kΩ ÷ 16.8 kΩ = 0.4048.
- Vout = Vin × ratio = 12 V × 0.4048 = 4.857 V.
- Divider current = Vin ÷ (R1 + R2) = 12 V ÷ 16.8 kΩ = 714.3 µA.
- Power: R1 = I² × R1 = 5.102 mW; R2 = Vout² ÷ R2 = 3.469 mW; the source supplies 8.571 mW.
- Thevenin source resistance = R1‖R2 = 10 kΩ × 6.8 kΩ ÷ (10 kΩ + 6.8 kΩ) = 4.048 kΩ: it is what the output looks like it is driven through.
Divider ratios with R1 = 10 kΩ and every E12 value for R2
| R2 | Vout ÷ Vin | Vout at 3.3 V in | Vout at 5 V in | Vout at 12 V in | R1‖R2 |
|---|---|---|---|---|---|
| 1 kΩ | 0.09091 | 0.3 V | 0.4545 V | 1.091 V | 909.1 Ω |
| 1.2 kΩ | 0.1071 | 0.3536 V | 0.5357 V | 1.286 V | 1.071 kΩ |
| 1.5 kΩ | 0.1304 | 0.4304 V | 0.6522 V | 1.565 V | 1.304 kΩ |
| 1.8 kΩ | 0.1525 | 0.5034 V | 0.7627 V | 1.831 V | 1.525 kΩ |
| 2.2 kΩ | 0.1803 | 0.5951 V | 0.9016 V | 2.164 V | 1.803 kΩ |
| 2.7 kΩ | 0.2126 | 0.7016 V | 1.063 V | 2.551 V | 2.126 kΩ |
| 3.3 kΩ | 0.2481 | 0.8188 V | 1.241 V | 2.977 V | 2.481 kΩ |
| 3.9 kΩ | 0.2806 | 0.9259 V | 1.403 V | 3.367 V | 2.806 kΩ |
| 4.7 kΩ | 0.3197 | 1.055 V | 1.599 V | 3.837 V | 3.197 kΩ |
| 5.6 kΩ | 0.359 | 1.185 V | 1.795 V | 4.308 V | 3.59 kΩ |
| 6.8 kΩ | 0.4048 | 1.336 V | 2.024 V | 4.857 V | 4.048 kΩ |
| 8.2 kΩ | 0.4505 | 1.487 V | 2.253 V | 5.407 V | 4.505 kΩ |
Best E24 and E96 pair for common voltage steps
| Step | E24 pair (R1 / R2) | E24 Vout | E24 error | E96 pair (R1 / R2) | E96 Vout | E96 error |
|---|---|---|---|---|---|---|
| 5 V to 3.3 V | 4.7 kΩ / 9.1 kΩ | 3.297 V | −0.08783% | 13.7 kΩ / 26.7 kΩ | 3.304 V | +0.135% |
| 12 V to 5 V | 18 kΩ / 13 kΩ | 5.032 V | +0.6452% | 10.5 kΩ / 7.5 kΩ | 5 V | 0% |
| 9 V to 3.3 V | 6.2 kΩ / 3.6 kΩ | 3.306 V | +0.1855% | 28 kΩ / 16.2 kΩ | 3.299 V | −0.04114% |
| 24 V to 5 V | 9.1 kΩ / 2.4 kΩ | 5.009 V | +0.1739% | 52.3 kΩ / 13.7 kΩ | 4.982 V | −0.3636% |
| 5 V to 1.8 V | 11 kΩ / 6.2 kΩ | 1.802 V | +0.1292% | 9.76 kΩ / 5.49 kΩ | 1.8 V | 0% |
| 3.3 V to 1.8 V | 10 kΩ / 12 kΩ | 1.8 V | 0% | 13.7 kΩ / 16.5 kΩ | 1.803 V | +0.1656% |
| 12 V to 3.3 V | 24 kΩ / 9.1 kΩ | 3.299 V | −0.02746% | 13.7 kΩ / 5.23 kΩ | 3.315 V | +0.4658% |
How a load pulls the output down (5 V, 10 kΩ over 10 kΩ)
| RL | RL ÷ R2 | Vout with the load | Loading error |
|---|---|---|---|
| 10 kΩ | 1 | 1.667 V | −33.33% |
| 20 kΩ | 2 | 2 V | −20% |
| 50 kΩ | 5 | 2.273 V | −9.091% |
| 100 kΩ | 10 | 2.381 V | −4.762% |
| 200 kΩ | 20 | 2.439 V | −2.439% |
| 500 kΩ | 50 | 2.475 V | −0.9901% |
| 1 MΩ | 100 | 2.488 V | −0.4975% |
Worked examples
| Situation | Inputs | Answer | Divider current |
|---|---|---|---|
| Equal resistors halve the voltage | 5 V in, R1 = 10 kΩ, R2 = 10 kΩ | Vout = 2.5 V | 250 µA |
| Resistors typed the shop way (10K and 4k7) | 12 V in, R1 = 10 kΩ, R2 = 4.7 kΩ | Vout = 3.837 V | 816.3 µA |
| A 4.7 kΩ over 10 kΩ divider on 5 V | 5 V in, R1 = 4.7 kΩ, R2 = 10 kΩ | Vout = 3.401 V | 340.1 µA |
| Which R2 gives 5 V from 12 V with R1 = 10 kΩ? | 12 V in, 5 V out, R1 = 10 kΩ, E24 values | R2 = 7.143 kΩ exactly, use 6.8 kΩ | 714.3 µA |
| Which R1 gives 3.3 V from 9 V with R2 = 10 kΩ? | 9 V in, 3.3 V out, R2 = 10 kΩ, E24 values | R1 = 17.27 kΩ exactly, use 18 kΩ | 321.4 µA |
| Closest E24 pair for 3.3 V from 5 V | 5 V in, 3.3 V out, E24 values from 1 kΩ to 100 kΩ | R1 = 4.7 kΩ, R2 = 9.1 kΩ | 362.3 µA |
| The same step with E96 (1%) values | 5 V in, 3.3 V out, E96 values from 1 kΩ to 100 kΩ | R1 = 13.7 kΩ, R2 = 26.7 kΩ | 123.8 µA |
| A 10 kΩ load on a 10 kΩ and 10 kΩ divider | 5 V in, R1 = 10 kΩ, R2 = 10 kΩ, load RL = 10 kΩ | Vout = 1.667 V with the load | 333.3 µA |
Standard resistor values: E12, E24 and E96
| Series | Tolerance | Values per decade | Values in one decade |
|---|---|---|---|
| E12 | ±10% | 12 | 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2 |
| E24 | ±5% | 24 | 1.0, 1.1, 1.2, 1.3, 1.5, 1.6, 1.8, 2.0, 2.2, 2.4, 2.7, 3.0, 3.3, 3.6, 3.9, 4.3, 4.7, 5.1, 5.6, 6.2, 6.8, 7.5, 8.2, 9.1 |
| E96 | ±1% | 96 | 1.00, 1.02, 1.05, 1.07, 1.10, 1.13, 1.15, 1.18, 1.21, 1.24, 1.27, 1.30, 1.33, 1.37, 1.40, 1.43, 1.47, 1.50, 1.54, 1.58, 1.62, 1.65, 1.69, 1.74, 1.78, 1.82, 1.87, 1.91, 1.96, 2.00, 2.05, 2.10, 2.15, 2.21, 2.26, 2.32, 2.37, 2.43, 2.49, 2.55, 2.61, 2.67, 2.74, 2.80, 2.87, 2.94, 3.01, 3.09, 3.16, 3.24, 3.32, 3.40, 3.48, 3.57, 3.65, 3.74, 3.83, 3.92, 4.02, 4.12, 4.22, 4.32, 4.42, 4.53, 4.64, 4.75, 4.87, 4.99, 5.11, 5.23, 5.36, 5.49, 5.62, 5.76, 5.90, 6.04, 6.19, 6.34, 6.49, 6.65, 6.81, 6.98, 7.15, 7.32, 7.50, 7.68, 7.87, 8.06, 8.25, 8.45, 8.66, 8.87, 9.09, 9.31, 9.53, 9.76 |
How to calculate a voltage divider
- Choose what you want to find. Pick "Find Vout" to get the output of resistors you already have, "Find R1 or R2" to get the resistor that gives a target Vout when you know the other one, or "Closest standard pair" to get the best-matching E12, E24 or E96 resistors for a step such as 5 V to 3.3 V.
- Enter Vin and the resistors. Type the input voltage (the example is 12 V) and the resistances in ohms. Values may be written 10k, 4.7k, 4k7, 2M2, 4R7 or 1e3. R1 is the top resistor, from Vin to the output; R2 is the bottom one, from the output to ground.
- Add the load if the output feeds something. If the output drives a circuit with a known resistance, type it as the load RL. It sits in parallel with R2, so it lowers the output: a 100 kΩ load on the example gives 4.668 V, −3.89% from the unloaded 4.857 V.
- Read the output, current and power. The result shows Vout (4.857 V for the example), the divider current (714.3 µA), the power in each resistor (5.102 mW and 3.469 mW) and the Thevenin source resistance (4.048 kΩ).
- Pick standard values and check the error. For a target output the tool shows the exact resistor and the closest standard values either side with the output each gives: for 5 V from 12 V with R1 = 10 kΩ, the exact R2 is 7.143 kΩ and the closest E24 value is 6.8 kΩ. Check that the error and the resistor power suit your circuit.
Frequently asked questions
- What is the voltage divider formula?
- Vout = Vin × R2 ÷ (R1 + R2), with R1 on the Vin side and R2 on the ground side, and the output taken at the junction. For 12 V in, R1 = 10 kΩ, R2 = 6.8 kΩ that is 12 V × 6.8 kΩ ÷ (10 kΩ + 6.8 kΩ), which is 4.857 V. The ratio 0.4048 depends only on the two resistances, never on the voltage.
- How do I choose R1 and R2 for a target output voltage?
- Fix the ratio first: Vout ÷ Vin = R2 ÷ (R1 + R2). Then pick one resistor to suit the current you can afford, and solve for the other: R2 = R1 × Vout ÷ (Vin − Vout). For 5 V from 12 V with R1 = 10 kΩ, R2 = 7.143 kΩ. Real resistors come in standard values, so the tool shows the nearest ones: 6.8 kΩ gives 4.857 V (−2.857%). Solving for R1 works the same way: for 3.3 V from 9 V with R2 = 10 kΩ, R1 = 17.27 kΩ, and the closest E24 value is 18 kΩ.
- How do I find the closest standard resistor pair?
- Choose "Closest standard pair", enter Vin and the target, and pick E12, E24 or E96. The tool tries every R1 and R2 of the series between the range you pick (1 kΩ to 100 kΩ by default), computes each pair's output and lists the five with the smallest error; pairs with the same ratio count once. For 3.3 V from 5 V the best E24 pair is R1 = 4.7 kΩ, R2 = 9.1 kΩ (−0.08783%), and the best E96 pair is R1 = 13.7 kΩ, R2 = 26.7 kΩ (+0.135%).
- Which E-series should I use: E12, E24 or E96?
- Each series has more values per decade, so a pair can sit closer to the exact ratio: E12 has 12 values (±10% parts), E24 24 (±5%) and E96 96 (±1%). For 5 V from 12 V with R1 = 10 kΩ the closest E12 value is 6.8 kΩ, giving 4.857 V (−2.857%); E24 also gives 6.8 kΩ; E96 gives 7.15 kΩ, which is 5.003 V (+0.05831%). A fine value is no use if the part's tolerance is wider than the error you are trying to remove.
- How does a load change the output voltage?
- A load RL across the output is in parallel with R2, so the bottom of the divider is R2 ‖ RL, which is always smaller than R2, and Vout falls. With 10 kΩ over 10 kΩ at 5 V, a 10 kΩ load takes the output from 2.5 V to 1.667 V (−33.33%). The error shrinks as RL grows relative to R2: the loading table above runs from RL equal to R2 to a hundred times R2. To get the target with a known load, enter RL in "Find R1 or R2": for 5 V from 12 V with R1 = 10 kΩ and a 100 kΩ load, R2 must be 7.692 kΩ instead of 7.143 kΩ.
- How big should the resistors be?
- It is a trade-off. Small values waste current: the example divider draws 714.3 µA and 8.571 mW. Ten times larger values draw a tenth of that, but a load disturbs them far more: with a 100 kΩ load, the example's loading error is −3.89%, while 100 kΩ over 68 kΩ (the same ratio) has −28.81%. A common approach is to make the load resistance many times larger than R2 and accept the current that implies; the tool shows both so you can judge.
- Can a voltage divider power a circuit?
- Not usefully. The output behaves like a source of Vth = the unloaded Vout through a source resistance R1‖R2 (Thevenin's theorem), here 4.048 kΩ. Any load current drops the voltage across that resistance. A 50 Ω load, which would draw 100 mA at 5 V, takes the example's output from 4.857 V to 0.05927 V. Dividers suit signals that draw almost no current (reference or sense inputs); use a regulator for a supply rail.
- What is the Thevenin source resistance of a divider?
- It is R1 in parallel with R2, R1 × R2 ÷ (R1 + R2): the resistance you would measure at the output with the input source replaced by a short. For 10 kΩ and 6.8 kΩ it is 4.048 kΩ. It matters when the output feeds an input that has its own resistance or a capacitor: a high source resistance gives a slow response and a larger error from input leakage. That is why dividers for such inputs use smaller values.
- How much does resistor tolerance change the output?
- Both resistors can be off in opposite directions, so the worst case is wider than either tolerance alone. For the example divider (4.857 V nominal), ±5% resistors (E24 grade) give 4.571 V to 5.149 V, and ±1% resistors (E96 grade) give 4.799 V to 4.915 V. Use the worst-case range, not the nominal figure, when the output must stay inside a limit.
- What power rating do the resistors need?
- Each resistor dissipates the voltage across it times the current: R1 gets (Vin − Vout) × I, R2 gets Vout × I. The example divider dissipates 5.102 mW in R1 and 3.469 mW in R2, far below a small resistor's rating; the tool adds a note when any resistor goes above 1/4 W. Higher supply voltages and smaller resistors raise the power quickly: it grows with the square of the voltage.
- How do I type resistor values like 4k7 or 2M2?
- Resistances are read in ohms. Accepted: a plain number (470, 4.7), a number with a suffix k, K, M or meg (4.7k, 10K, 2.2M, 1meg), an exponent (1e3, 4.7e3), and the letter-as-decimal-point style printed on schematics (4k7 is 4.7 kΩ, 2M2 is 2.2 MΩ, 4R7 is 4.7 Ω, R47 is 470 mΩ). A trailing Ω or "ohm" and spaces are ignored. A lowercase m is refused because it could mean milli or mega: write M or meg. Example: 10K over 4k7 at 12 V gives 3.837 V.
- Can I use this for mains or other high voltages?
- No. The tool stops at 50 V on purpose: a higher Vin gets the message "Vin must be between 0.01 V and 50 V: this tool is for low-voltage electronics." A divider for measuring mains or other hazardous voltages needs parts rated for that voltage and a safe, isolated design, and this page gives no guidance for that.
How it works
The divider is two resistors in series across Vin with the output at their junction: Vout = Vin × R2 ÷ (R1 + R2) and the current is Vin ÷ (R1 + R2). A load RL in parallel with R2 replaces R2 by R2 × RL ÷ (R2 + RL) in the same formulas; the loading error is the loaded output minus the unloaded one, divided by the unloaded one. The power in R1 is I² × R1, in R2 and in the load Vout² ÷ R, and the total is Vin × I. The Thevenin source resistance is R1 × R2 ÷ (R1 + R2). All of this is exact fraction arithmetic (BigInt numerator and denominator) and is rounded only when displayed, to four significant digits. Resistor input accepts plain decimals, the suffixes k, K, M and meg, exponents (1e3) and the RKM letter-as-decimal-point style (4k7, 2M2, 4R7, R47) in ohms, between 1 Ω and 100 MΩ; a lowercase m is refused as ambiguous. To solve for R2 the tool uses R2 = R1 × Vout ÷ (Vin − Vout) (taking RL out of the parallel pair when a load is given), and for R1 it uses R1 = R2 × (Vin − Vout) ÷ Vout; it then finds the series values just below and above the exact result, computes the output each would give and offers the closer one (the lower on an exact tie). The closest-pair search uses floating point only to rank candidates: it tries every R1 and R2 of the chosen series between the range ends (100 Ω to 10 kΩ, 1 kΩ to 100 kΩ or 10 kΩ to 1 MΩ), keeps one pair for each distinct ratio (the one whose resistors lie nearest the middle of the range on a log scale) and sorts by the absolute error of Vout, then recomputes the five best exactly. The E12 and E24 tables are the standard rounded tables of IEC 60063 (E12 ±10%, E24 ±5%), stored as constants; the E96 table (±1%) is the three-digit rounding of 10^(k/96), and the test suite checks the stored list against that formula. Ideal resistors and a steady, stiff source are assumed: real resistors differ by their tolerance, change with temperature, and a real source has its own resistance, so treat the result as the nominal output. Vin is limited to 0.01 V to 50 V because the tool is for low-voltage electronics; it gives no advice about mains or other hazardous voltages.
Sources
- Voltage divider, Wikipedia (formula, loading, Thevenin equivalent)
- Thévenin's theorem, Wikipedia
- E series of preferred numbers (IEC 60063), Wikipedia
- RKM code (the 4k7 notation), Wikipedia
- IEC 60063: preferred number series for resistors and capacitors (the standard behind E12, E24 and E96)
More free tools
- LED Resistor CalculatorFind the series resistor for an LED from supply, forward voltage and current: exact and E12/E24 value, color bands, power rating and efficiency.
- Resistor Color Code CalculatorRead 3, 4, 5 and 6 band resistor colors (IEC 60062) or turn a value into bands, check it against the E-series, and decode SMD codes including EIA-96.
- Electrical Box Fill CalculatorCheck electrical box fill under NEC 314.16: count conductors, grounds, clamps, devices and loops, compare with the box volume, and see pass or fail.
- Feet and Inches CalculatorAdd, subtract, multiply and divide lengths like 5' 7 3/8" with exact fractions, rounded to 1/16 inch, plus decimal feet, mm and cm and a tape view.
- Board Foot CalculatorBoard feet for a whole cut list: pieces × thickness × width × length, 4/4 to 16/4 hardwood or nominal 2×4s, with waste and the cost at your price.
- Slope CalculatorSlope from rise and run as percent, degrees and ratio (1:12). Convert 2% or 20% slope to degrees and find the drop over 10 ft. Feet, inches or metric.