Skip to main content
ponderloop

Concrete Weight Calculator: How Much Does a Slab, Footing or Column Weigh?

A 10 × 10 ft concrete slab 4 in thick holds 33.3 cu ft (1.23 cu yd) and weighs about 4,833 lb (2.42 US tons) at 145 lb per cubic foot, the typical figure for plain normal-weight concrete. That is 2,192 kg (2.19 metric tonnes). With steel at 150 lb/ft³ it is 5,000 lb; structural lightweight concrete at about 105 lb/ft³ is 3,500 lb. Enter the shape, size and concrete type for your pour.

Figures based on the sources listed belowUpdated How we calculate

How thick a slab or footing is, or how tall a column or block is, in inches (4 in slab, 48 in column).

How many identical slabs, footings, columns or blocks. The weight is for all of them together.
Typical unit weights, not mix-specific. Some agencies use 150 lb/ft³ for plain and 155 lb/ft³ for reinforced concrete: pick Custom to use those. A supplier ticket or the mix design is the exact figure.

4,833 lb (2.42 US tons).

4,833 lb (2.42 US tons)

  • Weight: 4,833 lb (2.42 US tons)
  • Metric weight: 2,192 kg (2.19 metric tonnes)
  • Volume of concrete: 33.33 cu ft = 1.23 cu yd = 0.94 m³
  • Unit weight used: 145 lb/ft³ (2,323 kg/m³)
  • Half-ton pickup loads at 1,500 lb payload (estimate): 4 loads; the payload on the door-jamb sticker is often 1,500 to 2,300 lb
  • Utility trailer loads at 2,000 lb payload (estimate): 3 loads; a single-axle 5 × 10 to 6 × 12 ft trailer often carries about 1,900 to 2,100 lb
  • Share of a 10 cu yd ready-mix truck (estimate): 12% of a full 10 cu yd drum, which holds about 39,200 lb of this concrete; mixers carry about 8 to 10 cu yd

Shopping list

  • Tape measure
  • Hand truck
  • Trailer loading ramps
  • Ratchet straps
  • Platform scale
Show diagram

Saved projects

No saved projects yet.

Weight of concrete by type

Per cubic yard (27 cu ft), worked by this calculator from the unit weights it uses. Structural lightweight is the middle of the usual 90 to 115 lb/ft³ range; your mix may differ, so use the Custom option for a mix with a known weight.
Concrete typelb per cu ftkg per m³lb per cu ydUS tons per cu ydMetric tonnes per cu yd
Normal-weight, plain1452,3231,3050.650.59
Normal-weight, reinforced1502,4031,3500.680.61
Structural lightweight (middle of 90 to 115)1051,6829450.470.43

Weight of a slab per square foot by thickness

Pounds in one square foot of slab at each thickness, worked by this calculator. Multiply by the area; the last column is kg per square foot of plain concrete.
ThicknessPlain (lb/sq ft)Reinforced (lb/sq ft)Lightweight (lb/sq ft)Plain (kg/sq ft)
3.5 in42.343.830.619.2
4 in48.3503521.9
5 in60.462.543.827.4
6 in72.57552.532.9
8 in96.71007043.8
12 in14515010565.8

Weight of common pours

Worked by this calculator, no waste. Tons are US tons of 2,000 lb; tonnes are metric tonnes of 1,000 kg.
PourCu ydPoundsUS tonsKilogramsMetric tonnes
Patio slab, 10 × 10 ft × 4 in, plain1.234,8332.422,1922.19
Garage slab, 20 × 20 ft × 6 in, reinforced7.4130,0001513,60813.61
Driveway, 50 × 10 ft × 5 in, reinforced7.7231,25015.6314,17514.17
Strip footing, 40 ft × 20 in wide × 10 in deep, reinforced2.068,3334.173,7803.78
Four round columns, 12 in × 8 ft, reinforced0.933,7701.881,7101.71
Precast block, 2 × 2 ft × 24 in, plain0.31,1600.585260.53

Hauling the same pours (estimate)

Loads at a 1,500 lb half-ton pickup payload and a 2,000 lb utility trailer payload, rounded up, and the share of a 10 cu yd ready-mix truck. Estimates: use the payload on your own vehicle’s label.
PourPoundsPickup loadsTrailer loadsShare of a 10 cu yd truck
Patio slab, 10 × 10 ft × 4 in, plain4,8334312%
Garage slab, 20 × 20 ft × 6 in, reinforced30,000201574%
Driveway, 50 × 10 ft × 5 in, reinforced31,250211677%
Strip footing, 40 ft × 20 in wide × 10 in deep, reinforced8,3336521%
Four round columns, 12 in × 8 ft, reinforced3,770329%
Precast block, 2 × 2 ft × 24 in, plain1,160113%

Methodology & assumptions

Volume first: a rectangular piece is length × width × thickness, and a round column or pier is π × (diameter ÷ 2)² × height, times the number of pieces; length and width are in feet, thickness, height and diameter in inches (divide by 12), and 27 cubic feet make a cubic yard. Weight is the volume in cubic feet times the unit weight of the concrete in pounds per cubic foot. The unit weights are typical design values: 145 lb/ft³ for plain normal-weight concrete and 150 lb/ft³ with reinforcing steel, inside the 140 to 150 lb/ft³ (2,240 to 2,400 kg/m³) that the concrete industry gives for normal-weight concrete, and about 105 lb/ft³ for structural lightweight concrete, the middle of the usual 90 to 115 lb/ft³ range for in-place density. The real figure depends on the aggregate, the air and water content and the moisture: fresh concrete is a few pounds per cubic foot heavier than the same concrete dried to equilibrium, and the plain and reinforced figures here are conventions, not measurements of your mix. Some agencies use 150 lb/ft³ for plain concrete and about 5 lb/ft³ more (155) with reinforcement; the Custom option takes any unit weight you give it, such as 155. The default 10 × 10 ft slab 4 in thick is 33.33 cu ft, 1.235 cu yd, so 145 lb/ft³ gives 4,833 lb, 2.42 US tons (2,000 lb each) and 2,192 kg (1 lb = 0.45359237 kg), 2.19 metric tonnes (1,000 kg). No waste is added, since the pour is the weight that ends up in place; to order concrete use the slab, footing or column calculator, which add waste. Hauling context is an estimate: a half-ton pickup is taken to carry 1,500 lb (typical ratings run about 1,500 to 2,300 lb, so read the sticker in the door jamb), a single-axle utility trailer about 2,000 lb (5 × 10 to 6 × 12 ft models are commonly rated near 1,900 to 2,100 lb of payload), and a ready-mix truck drum holds about 8 to 10 cu yd; the page uses 10. Never load past a vehicle's rated payload or axle rating, and remember that a wet load from a mixer or a stack of precast pieces is dense and shifts. Weight is not strength, and this tool does not size anything structurally: for loads on a floor, a deck or a lift, ask an engineer.

How to calculate the weight of concrete

  1. Find the volume. Length × width × thickness for a slab, footing or block (inches divided by 12 for feet), or π × radius² × height for a round column. Multiply by the number of pieces.
  2. Pick the unit weight. Plain normal-weight concrete is about 145 lb per cubic foot, reinforced about 150, structural lightweight about 90 to 115. Use your supplier's figure if you have it.
  3. Multiply to get pounds. Volume in cubic feet × pounds per cubic foot is the weight in pounds.
  4. Convert to tons and kilograms. Divide by 2,000 for US tons, multiply by 0.4536 for kilograms, and divide the kilograms by 1,000 for metric tonnes.
  5. Check the haul. Compare the weight with the payload on your pickup or trailer label. Both are estimates until you read the sticker; ask the supplier about delivery.

Worked examples

ProjectResult
10 × 10 ft patio slab, 4 in thick, plain concrete4,833 lb (2.42 US tons): 33.3 cu ft (1.23 cu yd), 2,192 kg
The same slab, reinforced (150 lb/ft³)5,000 lb (2.5 US tons)
The same slab in structural lightweight concrete (105 lb/ft³)3,500 lb (1.75 US tons)
20 × 20 ft garage slab, 6 in thick, reinforced30,000 lb (15 US tons): 7.41 cu yd, 13.6 metric tonnes
Strip footing 40 ft long, 20 in wide, 10 in deep, reinforced8,333 lb (4.17 US tons): 2.06 cu yd
Four round columns, 12 in diameter, 96 in tall, reinforced3,770 lb (1.89 US tons) in all: 25.1 cu ft, 942 lb each
Solid block 2 × 2 ft, 24 in tall, plain1,160 lb (0.58 US tons): 8 cu ft, too heavy to lift by hand
The 10 × 10 × 4 in slab at a custom 155 lb/ft³5,167 lb (2.58 US tons)

Frequently asked questions

How much does a cubic yard of concrete weigh?
About 3,915 lb (1.96 US tons, 1,776 kg) for plain normal-weight concrete at 145 lb per cubic foot, and 4,050 lb (2.03 US tons) at 150 lb/ft³ with steel. Roughly 4,000 lb per cubic yard is the usual rule of thumb. Structural lightweight concrete is about 2,835 lb at 105 lb/ft³. These are typical figures, not your mix. To convert a cubic yard order of concrete, gravel or sand into tons, use the cubic yards to tons converter.
How much does a concrete slab weigh?
Multiply the volume in cubic feet by the unit weight. A 4 in slab weighs about 48 lb per square foot (plain, 145 lb/ft³), so a 10 × 10 ft patio is 4,833 lb (2.42 US tons). A 6 in garage slab, 20 × 20 ft, reinforced, is 30,000 lb (15 US tons). The slab table above lists pounds per square foot from 3.5 to 12 in.
What is the weight of concrete per cubic foot?
Normal-weight concrete is about 140 to 150 lb per cubic foot; this calculator uses 145 for plain and 150 for reinforced concrete. Structural lightweight concrete is about 90 to 115 lb/ft³ (the calculator uses 105). In metric, 150 lb/ft³ is about 2,400 kg/m³. Pick Custom to use another figure, for example the weight on your supplier's ticket.
Is reinforced concrete heavier than plain concrete?
Slightly. Steel is much denser than concrete, but a typical slab or footing has little of it by volume, so design practice adds about 5 lb/ft³: 145 to 150, or 150 to 155 on the figures some agencies use. A 10 × 10 × 4 in slab is 4,833 lb plain and 5,000 lb reinforced here. Heavily reinforced members weigh more again.
How many US tons and metric tonnes is that?
A US (short) ton is 2,000 lb and a metric tonne is 1,000 kg, about 2,205 lb. The default 10 × 10 × 4 in slab weighs 4,833 lb: 2.42 US tons, 2,192 kg or 2.19 metric tonnes. A long ton, used in the UK, is 2,240 lb and is not used here.
Can my pickup or trailer carry it?
Check the payload on the door-jamb sticker for a pickup, often 1,500 to 2,300 lb for a half-ton, and the rating of the trailer, about 2,000 lb of cargo for a small single-axle utility trailer (estimates). A cubic foot of concrete is 145 lb, so a half-ton pickup holds roughly ten cubic feet, a little over a third of a cubic yard. The default slab, at 4,833 lb (2.42 US tons), is a job for a delivery truck, not a pickup; the haul table above gives load counts.
How much does a ready-mix truck load weigh?
A full 10 cu yd drum is about 40,500 lb of concrete, about 20 US tons, before the truck itself. Mixers carry about 8 to 10 cu yd (an estimate). The truck's own weight comes on top.
What about a block or a bag of concrete?
Enter a block as a rectangular piece: a solid 2 × 2 ft block 24 in tall is 1,160 lb (0.58 US tons). An 80 lb bag of mix makes about 0.6 cu ft of concrete, which weighs about 87 lb once mixed with water. Hollow concrete masonry units weigh much less than a solid piece of the same size; use the weight printed by the maker.
Why is my concrete heavier or lighter than this?
The unit weight depends on the aggregate (dense stone raises it, expanded shale or slate lowers it), the air content and the moisture. Fresh concrete is a few pounds per cubic foot heavier than the same concrete after it has dried to equilibrium. The figures here are typical design values; for an exact number use the weight on the batch ticket or from a test cylinder.

Handy tools

Related calculators