Electric Baseboard Heater Size Calculator: Watts, Length and Breaker
A 15 × 12 ft room (180 sq ft) with 8 ft ceilings and average insulation needs about 1,800 W of electric baseboard heat by the common rule of thumb of 10 watts per square foot. At about 250 W per foot that is 7.2 ft of heater: one 8 ft, 2,000 W unit covers it, and it draws 8.3 A at 240 V, so the circuit needs a 15 A breaker (125% of the load for a continuous heater). Running at full power it costs about $0.33 an hour at 18.31¢ per kWh. Better insulation lowers the figure (7 W/sq ft) and an older, drafty room raises it (13 W/sq ft). This is a rule of thumb, an estimate, not a heat-loss calculation; the cross-check line shows the room heat loss method for the same room. This page sizes electric baseboard heaters; for baseboard trim molding use the baseboard (trim) calculator instead.
Figures based on the sources listed belowUpdated How we calculate
1,800 W.
1,800 W
- Heat for the room (rule of thumb): 1,800 W (180 sq ft × 10 W/sq ft, average)
- Same heat in BTU/h: 6,142 BTU/h (1,800 W × 3.41214); resistance heat turns all its electricity into heat
- Baseboard length needed: 7.2 ft, 1,800 W ÷ 250 W per ft
- Heaters to buy: 1 heater: 1 × 8 ft (2,000 W); 2,000 W installed at 240 V
- Current at 240 V: 8.3 A (2,000 W installed ÷ 240 V)
- Circuit breaker (125% of the load): 15 A breaker (8.3 A × 1.25 = 10.4 A, next standard size); an electrician sets the wire and breaker
- Circuits if you use 20 A breakers: 1 (a 20 A circuit carries 3,840 W of continuous heat at 240 V)
- The plain 10 W per sq ft rule, same room: 1,800 W (180 sq ft × 10 W); it ignores ceiling height, climate and how well the room is insulated
- Running cost at full output: $0.33 per hour (1.8 kW × 18.31¢ per kWh)
- Running cost per month: $79.1 per 30-day month (432 kWh: 1.8 kW × 8 full-power hours a day × 30 days)
- Cross-check: room heat loss method: 848 W (2,893 BTU/h at a 60°F difference) by U × area × ΔT for walls 943, windows 900 and ceiling 272 plus air leakage 778 BTU/h, assuming R-13 walls with drywall, R-38 ceiling, double-pane windows, 0.5 air changes per hour. The rule of thumb is 112% higher
Shopping list
- Line-voltage wall thermostat
- Electric baseboard heater, 240 V
- Baseboard heater cord kit
- Weatherstripping
- Tape measure (25 ft)
Your project
- Room length × room width: 15 × 12 ft
- Ceiling height: 8 ft
- Insulation level: Average: typical insulation (10 W/sq ft)
- Climate: Moderate winters (× 1.0)
- Supply voltage: 240 V (two-pole circuit)
- Longest heater that fits the wall: 8 ft (2,000 W)
- Exterior wall length: 27 ft
- Window area: 30 sq ft
- Outdoor design temperature: 10 °F
- Electricity price: 18.31 ¢/kWh
- Full-power hours per day: 8 hours
Also pick up
- Line-voltage wall thermostat
- Electric baseboard heater, 240 V
- Baseboard heater cord kit
- Weatherstripping
- Tape measure (25 ft)
Reopen this calculation: /calculators/baseboard-heater-size/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjoxNSwid2lkdGhGdCI6MTJ9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMSwicGFyYW1zIjp7ImNlaWxpbmdGdCI6OCwiaW5zdWxhdGlvbiI6MSwiY2xpbWF0ZSI6MSwidm9sdHMiOjI0MCwibWF4TGVuRnQiOjgsIndhbGxGdCI6MjcsIndpbmRvd1NxRnQiOjMwLCJvdXRkb29yRiI6MTAsInJhdGVDZW50cyI6MTguMzEsImhvdXJzUGVyRGF5Ijo4fX0
Show diagram
Saved projects
No saved projects yet.
Watts by insulation and climate for a 15 × 12 ft room, 8 ft ceiling
| Insulation level | Base rule | Moderate winters | Mild winters | Cold winters |
|---|---|---|---|---|
| Older or drafty | 13 W/sq ft | 2,340 W | 2,106 W | 2,691 W |
| Average | 10 W/sq ft | 1,800 W | 1,620 W | 2,070 W |
| Well insulated | 7 W/sq ft | 1,260 W | 1,134 W | 1,449 W |
Heater watts by room size and insulation, 8 ft ceiling, moderate winters
| Room | Well insulated | Average | Older or drafty | Heaters for average |
|---|---|---|---|---|
| Bathroom, 5 × 8 ft (40 sq ft) | 280 W | 400 W | 520 W | 1 × 3 ft (750 W) |
| Small bedroom, 10 × 10 ft (100 sq ft) | 700 W | 1,000 W | 1,300 W | 1 × 4 ft (1,000 W) |
| Bedroom, 12 × 12 ft (144 sq ft) | 1,008 W | 1,440 W | 1,872 W | 1 × 6 ft (1,500 W) |
| Bedroom, 15 × 12 ft (180 sq ft) | 1,260 W | 1,800 W | 2,340 W | 1 × 8 ft (2,000 W) |
| Living room, 20 × 15 ft (300 sq ft) | 2,100 W | 3,000 W | 3,900 W | 1 × 8 ft (2,000 W) + 1 × 4 ft (1,000 W) |
| Large room, 25 × 20 ft (500 sq ft) | 3,500 W | 5,000 W | 6,500 W | 2 × 8 ft (2,000 W) + 1 × 4 ft (1,000 W) |
Common 240 V baseboard lengths, watts, amps and breakers
| Length | Watts at 240 V | Heat output | Current | Breaker (125%) | Covers at 10 W/sq ft |
|---|---|---|---|---|---|
| 3 ft (36 in) | 750 W | 2,559 BTU/h | 3.1 A | 15 A | 75 sq ft |
| 4 ft (48 in) | 1,000 W | 3,412 BTU/h | 4.2 A | 15 A | 100 sq ft |
| 5 ft (60 in) | 1,250 W | 4,265 BTU/h | 5.2 A | 15 A | 125 sq ft |
| 6 ft (72 in) | 1,500 W | 5,118 BTU/h | 6.3 A | 15 A | 150 sq ft |
| 8 ft (96 in) | 2,000 W | 6,824 BTU/h | 8.3 A | 15 A | 200 sq ft |
How much heater a circuit carries
| Breaker | Most heater watts at 240 V | Most heater watts at 120 V |
|---|---|---|
| 15 A | 2,880 W | 1,440 W |
| 20 A | 3,840 W | 1,920 W |
| 30 A | 5,760 W | 2,880 W |
| 40 A | 7,680 W | 3,840 W |
What baseboard heat costs to run
| Heater | Per hour | Per month at 8 h/day | Per month at 24 h/day |
|---|---|---|---|
| 500 W | $0.09 | $21.97 | $65.92 |
| 1,000 W | $0.18 | $43.94 | $131.83 |
| 1,500 W | $0.27 | $65.92 | $197.75 |
| 2,000 W | $0.37 | $87.89 | $263.66 |
| 3,000 W | $0.55 | $131.83 | $395.5 |
Rule of thumb against the room heat loss method, 15 × 12 ft room
| Insulation level | Rule of thumb | Heat-loss cross-check | Cross-check in BTU/h | Ratio |
|---|---|---|---|---|
| Older or drafty | 2,340 W | 2,097 W | 7,156 BTU/h | 1.1 × |
| Average | 1,800 W | 848 W | 2,893 BTU/h | 2.1 × |
| Well insulated | 1,260 W | 630 W | 2,150 BTU/h | 2 × |
Methodology & assumptions
This is a rule-of-thumb estimate, not a heat-loss calculation. 1) Base figure: the common rule is 10 watts per square foot of floor for a room with average insulation and an 8 ft ceiling. Dimplex’s support page gives it as "10 watts of heat per square foot of space" in a standard insulated room (a 1,000 W heater heats about 100 sq ft), and its blog says better insulation and air tightness have lowered the figure for newer homes to about 7 watts per square foot. Cadet gives a range of roughly 6 to 10 watts per square foot depending on the home’s construction, whether the heater is the only source of heat, and where you live. This page uses 7, 10 and 13 W/sq ft for well insulated, average and older or drafty rooms. The 7 and 10 come from Dimplex (Cadet’s 6 to 10 is the same span); the 13 is a typical figure: hobbyist and retailer guides print 12 to 15 W/sq ft for old, drafty construction, and this site takes a value inside that range. 2) Climate: the manufacturers say the need depends on climate but publish no multipliers, so the mild (× 0.9), moderate (× 1) and cold (× 1.15) adjustments are this site’s typical figures. Mild is roughly IECC climate zones 1 to 3, moderate 4 and 5, cold 6 and 7 (the zones the furnace size calculator on this site uses). 3) Ceiling height: the rule is for 8 ft ceilings, so the watts are multiplied by ceiling height ÷ 8 (a 10 ft ceiling needs 25% more), which treats the rule as watts per cubic foot of room. Cadet says to move up to the next wattage for high or vaulted ceilings, in the same direction. 4) Length: a 240 V residential baseboard gives about 250 watts per foot of heater. The Cadet F-Series sheet lists 750, 1,000, 1,250, 1,500 and 2,000 W at 3, 4, 5, 6 and 8 ft, and Marley’s Qmark 2500 series is listed at 1,000 W for 4 ft and 1,250 W for 5 ft, all at 250 W per foot; very short models (2 to 2.5 ft) run lower, about 200 W per foot. Required length = watts ÷ 250. 5) Number of units: baseboards are sold in fixed lengths, so the tool uses as many of the longest heater that fits your wall (you choose) as it takes, then the smallest single heater that covers the rest, from 3 ft, 4 ft, 5 ft, 6 ft, 8 ft. Amps and breaker use the installed watts, not the exact need, because that is what is on the circuit. A 208 V supply gives about 75% of the 240 V rating, so this tool does not cover 208 V. A 120 V run is limited to heaters up to 6 ft (1,500 W, 12.5 A), a typical size for 120 V models. 6) Amps: amps = watts ÷ volts (P ÷ V). 7) Breaker: fixed electric space heating counts as a continuous load, so the branch circuit conductors and breaker must be rated for at least 125% of the heater load (National Electrical Code Article 210 and 424); the tool shows the next standard breaker size (15, 20, 25, 30, 35, 40, 45, 50, 60 A) and flags anything above 60 A. Equivalent rule: load the circuit to no more than 80% of the breaker, which is where the "circuits if you use 20 A breakers" line comes from (3,840 W at 240 V, 1,920 W at 120 V). A 120 V plug-in heater on a 15 A circuit is limited to about 1,440 W. The breaker, wire gauge and whether your panel can carry the load are for a licensed electrician, and thermostats and heaters must be installed to the manufacturer’s instructions and local code. 8) Running cost: kW × full-power hours × rate. Resistance heat is essentially 100% efficient at the heater and gives 3,412.14 BTU per kWh (3.41214 BTU/h per watt); a thermostat cycles the heater, so you enter the hours a day it would run at full output. The default price is the U.S. average residential rate that the electricity cost calculator on this site uses. Heat pumps and mini-splits deliver the same heat for a fraction of the electricity and can cost much less to run than any electric resistance heater. 9) Cross-check with the room heat loss calculator on this site: that page adds up U-factor × area × temperature difference for each surface and 0.018 × air changes per hour × volume × temperature difference for air leakage, and this tool repeats that arithmetic for your room with the same constants (wall U-factor from the wall R-value calculator, ceiling U = 1 ÷ (R + 1.67), 70°F indoors, and the typical envelope listed for each insulation level on this page). It uses your exterior wall length, window area and outdoor design temperature; the floor is not counted, as if a heated room or a slab were below. The two answers will not match, and the difference is deliberate: the rule of thumb is a quick sizing figure built to work for a room with no other heat, and it leaves margin for floors over cold spaces, doors, drafts, a room with more outside wall than you entered and the time it takes to recover the temperature, while the heat-loss method is the steady-state loss on the design day for exactly the envelope you describe. For the default room the rule comes out at roughly 2.1 times the heat-loss figure. Dimplex itself points to a heat loss calculation as the more accurate method. If your heat-loss result is far below the rule, a smaller or shorter heater may heat the room, but heaters come in steps and the cost of a bigger one is low; if it is higher, trust the heat-loss figure and look at the windows and air leakage. Not covered: other heat sources already in the room, a room above a garage or an unheated space, very large windows, and which wall the heater goes on (under a window is usual), plus clearances and code, which the heater’s instructions and your local code decide.
- Cadet, Installing electric heaters: the maker’s sizing range of roughly 6 to 10 watts per square foot, depending on the home’s construction, whether the heater is the only source of heat and the part of the country
- Cadet, How to Pick the Right Wattage to Heat Your Room: for high or vaulted ceilings move up to the next wattage; a 250 sq ft room with central heat suits 1,500 W and the same room with no other heat suits 2,000 W
- Cadet, Electric Baseboard Heater product sheet (F-Series): models by length and wattage, 750 W at 3 ft up to 2,000 W at 8 ft at 240 V, 250 W per foot; the per-foot figure is worked out from the listed ratings, not stated by Cadet
- Dimplex, Electric Heater Technical Support: the general rule for electric heat of 10 watts per square foot in a standard insulated room (a 1,000 W heater heats about 100 sq ft), and a recommendation to use a heat loss calculation for an accurate figure
- Dimplex, 3 Myths Demystified About Electric Baseboard Heating: the traditional 10 watts per square foot rule has come down to about 7 watts per square foot for newer, better insulated and tighter homes. A manufacturer’s own claim, used for the well insulated level
- Marley Qmark 2500 Series 48 in Electric Baseboard Heater, 1000/752 W at 240/208 V (model 2544W), bulbs.com listing: 1,000 W at 4 ft, with the 752 W rating at 208 V
- Marley Qmark 2500 Series 60 in Electric Baseboard Heater, 1250/940 W at 240/208 V (model 2545W), bulbs.com listing: 1,250 W at 5 ft, again 250 W per foot
- Electrical Construction & Maintenance, Article 424: Fixed Electric Space Heating: fixed electric space heating is treated as a continuous load, so the branch-circuit conductors and overcurrent device are sized at 125% of the heater load (NEC 210.19(A)(1), 210.20(A) and 424.3(B), renumbered 424.4(B) in the 2020 edition)
- NFPA 70, National Electrical Code, Section 240.6(A): the standard ratings of overcurrent devices (15, 20, 25, 30, 35, 40, 45, 50, 60 A and up) used for the breaker line. Cited by name; check the edition your jurisdiction has adopted
- The room heat loss calculator on this site (U × area × ΔT and 0.018 × ACH × volume × ΔT, with the wall R-value calculator’s wall U-factor): the method behind the cross-check line. Its sources are listed on that page
- The electricity cost calculator on this site: the default price of 18.31¢ per kWh, the U.S. average residential rate (US Energy Information Administration data). Use your own rate
- Typical figures, not published tables: the 13 W/sq ft for older, drafty rooms, the climate multipliers, the 120 V limit of 6 ft, and the envelope assumed for each level in the cross-check. Treat every result here as an estimate
How to size an electric baseboard heater for a room
- Measure the room. Multiply the length by the width in feet to get square feet, and note the ceiling height. A 15 × 12 ft room is 180 sq ft.
- Pick the watts per square foot. Use about 10 W/sq ft for an average, 8 ft room, about 7 for a newer, well insulated one and about 13 for an older, drafty room. Move up a little for a cold climate and in proportion to the ceiling height over 8 ft.
- Multiply to get the watts. Watts = square feet × watts per square foot. For the example, 180 × 10 is 1,800 W.
- Convert to heater length and choose heaters. Divide the watts by about 250 W per foot for the length (7.2 ft), then choose the stock heater at or above that: 750, 1,000, 1,250, 1,500 and 2,000 W units are 3, 4, 5, 6 and 8 ft long.
- Size the circuit. Amps = installed watts ÷ volts (a 2,000 W heater is 8.3 A at 240 V). The breaker must carry 125% of that load, so use the next standard size up (15 A here). Have an electrician check the wire and the panel.
Worked examples
| Project | Result |
|---|---|
| 15 × 12 ft room, 8 ft ceiling, average insulation, moderate winters, 240 V | 1,800 W, 7.2 ft of heater (1 × 8 ft (2,000 W)), 8.3 A at 240 V on a 15 A breaker, $79.1 a month at 8 full-power hours a day |
| The same room, older or drafty (13 W/sq ft) | 2,340 W, 1 × 8 ft (2,000 W) + 1 × 3 ft (750 W), 11.5 A at 240 V |
| The same room, newer and well insulated (7 W/sq ft) | 1,260 W, 1 × 6 ft (1,500 W), 6.3 A at 240 V |
| The same room with a 10 ft ceiling (volume × 1.25) | 2,250 W, 1 × 8 ft (2,000 W) + 1 × 3 ft (750 W), 11.5 A at 240 V |
| The same room in a cold climate (× 1.15) | 2,070 W, 1 × 8 ft (2,000 W) + 1 × 3 ft (750 W), $90.96 a month |
| The same room on 120 V, heaters up to 6 ft | 1,800 W needed, 1 × 6 ft (1,500 W) + 1 × 3 ft (750 W) installed, 18.8 A at 120 V on a 25 A breaker |
| 12 × 10 ft bedroom with average insulation | 1,200 W, 1 × 5 ft (1,250 W), 5.2 A at 240 V |
| 10 × 10 ft small bedroom (100 sq ft, the 1,000 W heater rule of thumb) | 1,000 W, 1 × 4 ft (1,000 W), 4.2 A at 240 V |
| 25 × 20 ft living room with average insulation | 5,000 W, 2 × 8 ft (2,000 W) + 1 × 4 ft (1,000 W), 20.8 A at 240 V on a 30 A breaker (or 2 circuits of 20 A) |
Frequently asked questions
- How many watts of baseboard heat do I need per square foot?
- The common rule is 10 watts per square foot for a room with average insulation and an 8 ft ceiling; Dimplex states it that way, Cadet gives a range of about 6 to 10, and Dimplex says newer, tighter homes are now closer to 7. For the 15 × 12 ft room (180 sq ft) that is 1,800 W; with older, drafty construction at 13 W/sq ft it is 2,340 W, and well insulated at 7 W/sq ft it is 1,260 W. It is a rule of thumb, an estimate, so check it with a heat-loss calculation when the room is unusual.
- How long a baseboard heater do I need?
- Divide the watts by 250, the output of a 240 V baseboard per foot. 1,800 W is 7.2 ft, so one 8 ft, 2,000 W heater covers the default room. Baseboards are sold in fixed lengths (3, 4, 5, 6 and 8 ft are common), so pick the heater that is at or above the need; if the wall only has room for 4 ft heaters, the same room takes 2 × 4 ft (1,000 W).
- How many baseboard heaters do I need for a room?
- As few as cover the watts and fit the wall. The default 180 sq ft room needs 1 heater (1 × 8 ft (2,000 W)). A 500 sq ft room (25 × 20 ft) at the average level needs 5,000 W, which is 2 × 8 ft (2,000 W) + 1 × 4 ft (1,000 W). Putting the heater under the window, where the cold air falls, works better than several short ones spread around, and each heater needs its own thermostat or a shared line-voltage one.
- How many amps does a baseboard heater draw, and what breaker do I need?
- Amps = watts ÷ volts. A 2,000 W heater draws 8.3 A at 240 V (and 16.7 A at 120 V). A heater is a continuous load, so the circuit must carry 125% of that, 10.4 A, which makes a 15 A breaker the next standard size for one 8 ft heater. Several heaters on one circuit add up: 3,840 W is the most a 20 A, 240 V circuit should carry continuously. Wire gauge and the panel are for a licensed electrician.
- Should I use 120 V or 240 V baseboard heaters?
- Use 240 V for anything above about 1,000 W. The same heat takes half the current, so thinner wire and smaller breakers do the job, and a 120 V heater on a 15 A circuit is limited to about 1,440 W continuous. This calculator limits a 120 V room to heaters up to 6 ft (1,500 W); the default room then takes 1 × 6 ft (1,500 W) + 1 × 3 ft (750 W) and 18.8 A, against 8.3 A at 240 V. Match the heater’s voltage to your supply: a 240 V heater on 208 V gives only about 75% of its rating.
- How does ceiling height change the size?
- The 10 W/sq ft rule is for 8 ft ceilings. This calculator scales the watts by ceiling height ÷ 8, so a 10 ft ceiling needs 25% more: the default room goes from 1,800 W to 2,250 W. Cadet’s advice for high or vaulted ceilings is to move up to the next wattage or add a ceiling fan to push the warm air down.
- How does climate change the size?
- Cadet says the need depends on where you live, but neither maker publishes multipliers. This page uses × 0.9 for mild winters and × 1.15 for cold ones, typical figures: the default room goes from 1,800 W to 1,620 W in a mild climate and 2,070 W in a cold one. A 70°F room on a 0°F day loses far more heat than on a 40°F day, so for exact sizing use the room heat loss calculator with your design temperature.
- Is the 10 watts per square foot rule accurate?
- It is a starting point. Dimplex, which publishes the rule, also says to use a heat loss calculation for an accurate figure. The rule ignores windows, walls, ceiling height and air leakage. For the default room the room heat loss method gives 848 W (2,893 BTU/h at a 60°F difference) against 1,800 W by the rule, because the rule is built to work for a room with no other heat and leaves margin for floors, doors and drafts. Both are estimates; the heat-loss figure is better for deciding what insulation and windows would save.
- How much does it cost to run a baseboard heater?
- Cost = kW × hours × price per kWh. The default room (1,800 W, 1.8 kW) costs $0.33 an hour at full output at 18.31¢ per kWh, or $79.1 a month if it runs the equivalent of 8 full-power hours a day (432 kWh). A thermostat cycles the heater, so real use depends on the weather and the insulation. Electric resistance heat is simple and cheap to install but expensive to run next to a heat pump, which delivers the same heat for a fraction of the electricity.
- Is this the same as the baseboard (trim) calculator?
- No. This page sizes electric baseboard heaters in watts, feet of heater, amps and breaker. The baseboard (trim) calculator on this site is for the wood or MDF molding along the bottom of a wall: it counts linear feet and pieces of trim. If you are installing a heater, leave clearance between the heater and the floor covering and curtains, as its instructions say.
- Can I put a baseboard heater on a 15 A or 20 A circuit with other things?
- A heater should normally have its own circuit. At 240 V a 15 A breaker carries 2,880 W of continuous heat and a 20 A breaker 3,840 W; at 120 V it is 1,440 W and 1,920 W. Anything else on the circuit eats into that. Check the circuit, wire gauge and the panel’s capacity with an electrician, and never replace a heater with a larger one on existing wiring without checking it.
- What about a basement or an older, cold room?
- A 14 × 20 ft basement room with older construction (13 W/sq ft) in a cold climate (× 1.15) comes to 4,186 W by this rule, which is 2 × 8 ft (2,000 W) + 1 × 3 ft (750 W) and 19.8 A at 240 V. Below-grade rooms lose heat differently from rooms above ground and the rule is crude there, so run the room heat loss calculator before buying; insulating first often costs less than the extra heater and its running cost. A well insulated 12 × 14 ft room in a mild climate by contrast needs only 1,058 W.
Handy tools
- Electricity Cost Calculator: Turn the heater’s watts, your hours of use and your rate into a cost per day, month and year.
- Wire Size Calculator: Pick the wire gauge for the baseboard circuit once you know the amps and the run length.
- Voltage Drop Calculator: Check the voltage drop on a long run to a baseboard heater.