Sprinkler Run Time Calculator: How Long Should I Water My Lawn?
A 50 × 40 ft lawn zone (2,000 sq ft) with 15 GPM of rotors puts down 96.25 × 15 ÷ 2,000 = 0.72 in/h (18.3 mm/h). To give it 1 inch a week with a distribution uniformity of 0.65 takes 128 min of watering per week (1 ÷ 0.72 × 60 ÷ 0.65 = 127.87 minutes). On 3 days that is about 43 min a day, and on loam, which takes in about 0.4 in/h, each day should be split into 2 cycles of about 21 min with 30 minutes or more between them. That is roughly 1,918 gallons a week, against 1,247 gallons of water the grass needs.
Figures based on the sources listed belowUpdated How we calculate
128 min of watering per week.
128 min of watering per week
- Run time per week: 128 min (2.1 h)
- Precipitation rate: 0.72 in/h (18.3 mm/h)
- Water to apply per week: 1 in needed, 1.54 in applied at DU 0.65
- Run time per watering day: 43 min, 3 days a week
- Longest cycle before runoff (estimate): 33 min at 0.4 in/h soil intake
- Cycles per watering day: 2 cycles of 21 min, with 30 min or more to soak between
- Water the lawn needs per week: 1,246.8 gal
- Water the zone uses per week (with DU): 1,918.1 gal
Shopping list
- Rain gauge or catch cups for a sprinkler test
- Sprinkler timer / smart controller
- Rotary nozzles for spray heads
- Sprinkler flow meter
- Hose-end timer
Your project
- Zone length × zone width: 50 × 40 ft
- Find the precipitation rate from: Total flow of the zone (GPM)
- Total flow of the zone: 15 GPM
- Weekly water need from: A weekly depth (1 in is the usual start)
- Weekly water need: 1 in
- Rain this week: 0 in
- Distribution uniformity (DU): 0.65 (typical)
- Watering days per week: 3 days
- Soil type: Loam or sandy loam (about 0.4 in/h)
Also pick up
- Rain gauge or catch cups for a sprinkler test
- Sprinkler timer / smart controller
- Rotary nozzles for spray heads
- Sprinkler flow meter
- Hose-end timer
Reopen this calculation: /calculators/sprinkler-run-time/?s=eyJyb29tIjp7Imxlbmd0aEZ0Ijo1MCwid2lkdGhGdCI6NDB9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMSwicGFyYW1zIjp7InByTWV0aG9kIjoxLCJ0b3RhbEdwbSI6MTUsImN1cERlcHRoSW4iOjAuMjUsImN1cE1pbnV0ZXMiOjE1LCJoZWFkUmF0ZSI6MC42LCJuZWVkTW9kZSI6MSwid2Vla2x5TmVlZEluIjoxLCJ3ZWVrbHlFdG9JbiI6MS43NSwidHVyZktjIjowLjgsInJhaW5JbiI6MCwiZHUiOjAuNjUsImRheXNQZXJXZWVrIjozLCJpbmZpbHRyYXRpb24iOjAuNH19
Show diagram
Saved projects
No saved projects yet.
Typical head rates, weekly run time and longest cycle by soil
| Head | Typical rate | 1 in/week, DU 1.0 | 1 in/week, DU 0.65 | Cycle on clay | Cycle on silt loam | Cycle on loam | Cycle on sand |
|---|---|---|---|---|---|---|---|
| Fixed spray head | 1.75 in/h | 34 min | 53 min | 5 min | 10 min | 14 min | 34 min |
| Gear-drive rotor | 0.6 in/h | 100 min | 154 min | 15 min | 30 min | 40 min | 60 min |
| Hunter MP Rotator | 0.4 in/h | 150 min | 231 min | 23 min | 45 min | 60 min | 60 min |
Minutes per week for 1 inch, by precipitation rate and DU
| Precipitation rate | DU 1.0 | DU 0.75 | DU 0.65 | DU 0.55 |
|---|---|---|---|---|
| 0.4 in/h | 150 min | 200 min | 231 min | 273 min |
| 0.6 in/h | 100 min | 133 min | 154 min | 182 min |
| 0.8 in/h | 75 min | 100 min | 115 min | 136 min |
| 1 in/h | 60 min | 80 min | 92 min | 109 min |
| 1.5 in/h | 40 min | 53 min | 62 min | 73 min |
| 2 in/h | 30 min | 40 min | 46 min | 55 min |
Gallons for 1 inch by zone size
| Zone area | Needed for 1 in | Needed for 0.5 in | Used at 1 in, DU 0.65 | Rate at 10 GPM |
|---|---|---|---|---|
| 500 sq ft | 312 gal | 156 gal | 480 gal | 1.93 in/h |
| 1,000 sq ft | 623 gal | 312 gal | 959 gal | 0.96 in/h |
| 2,000 sq ft | 1,247 gal | 623 gal | 1,918 gal | 0.48 in/h |
| 3,000 sq ft | 1,870 gal | 935 gal | 2,877 gal | 0.32 in/h |
| 5,000 sq ft | 3,117 gal | 1,558 gal | 4,795 gal | 0.19 in/h |
Soil intake rate (typical)
| Soil | Used here | Extension range |
|---|---|---|
| Clay | 0.15 in/h | 0.04 to 0.20 in/h |
| Clay loam or silt loam | 0.3 in/h | 0.10 to 0.40 in/h |
| Loam or sandy loam | 0.4 in/h | 0.20 to 0.50 in/h |
| Sand | 1 in/h | about 0.5 to 1 in/h or more |
Methodology & assumptions
The precipitation rate (PR) is the depth of water the zone applies per hour. From the zone's total flow it is PR = 96.25 × GPM ÷ area in sq ft, where 96.25 comes from 60 minutes per hour ÷ 7.48 gallons per cubic foot × 12 inches per foot; use the sum of the flows of every head on the zone and the area those heads water. From a catch-cup test it is PR = average depth in the cups ÷ test minutes × 60, a measurement that includes whatever your nozzles, pressure and spacing really do. If you know neither, the head-type choice uses typical rates (an estimate): fixed sprays 1.75 in/h (typically 1.5 to 2), gear-drive rotors 0.6 in/h (typically 0.4 to 0.8) and Hunter's MP Rotator about 0.4 in/h, which Hunter publishes as matched across its range. The weekly need defaults to 1 inch of rain and irrigation together, the usual extension starting point for lawns in warm weather; hot, dry, windy weather can need more. As an alternative, enter the week's reference evapotranspiration (ETo) and the calculator uses turf water use = ETo × Kc, with Kc 0.8 for cool-season and 0.6 for warm-season grass (annual average coefficients). Rain you enter is subtracted from the need. The run time is then net need ÷ PR × 60 minutes, divided by the distribution uniformity (DU): DU is how evenly the zone waters, the driest quarter relative to the average, so running 1 ÷ DU as long as a perfectly even system puts the driest spots at the target depth. This is the simple rule and it overwaters the wetter areas; typical home systems score about 0.55 to 0.75 in these tools, and field studies of homes have found lower, so a catch-cup test is the way to know yours. The weekly time is split over the days you choose. Cycle and soak: if the heads apply water faster than the soil takes it in, the excess runs off. The calculator limits each cycle to the minutes in which the depth applied is no more than the soil's intake in inches per hour, which is 60 × intake ÷ PR minutes (never over 60). The number of cycles is the daily time divided by that limit, rounded up, and the time is shared equally between them. This is an estimate that is close to Texas A&M AgriLife's example for a clay soil under a 1.5 in/h spray (about 5 minutes a cycle); sloped, compacted or thatchy lawns take in less, so use shorter cycles. The intake figures are typical steady rates from extension tables: about 0.15 in/h for clay, 0.3 for clay loam or silt loam, 0.4 for loam or sandy loam and 1.0 for sand, and real soils vary a lot. Leave at least 30 minutes between cycles (a typical figure) so the water soaks in. Gallons: each inch on each square foot is 144 ÷ 231 = 0.6234 US gallons exactly (a cubic foot is 1,728 cubic inches and a gallon 231). "Water the lawn needs" is area × net inches × 0.6234; "water the zone uses" divides the inches by DU. Water pressure, wind, evaporation, root depth, local watering restrictions and the time of day are not modelled; run sprinklers early in the morning. Metric: lengths and depths follow the switch, PR is shown in both in/h and mm/h, and gallons become litres.
- Precipitation Rates and Sprinkler Irrigation, Irrigation Design Education Module: PR = 96.25 × GPM ÷ area, the constant being 60 ÷ 7.48 × 12; a 10 GPM example over 1,000 sq ft gives 0.96 in/h (figure not checked against the full document)
- Utah State University Extension, Simple Sprinkler Performance Testing (catch-can test: average depth over run time; about 0.5 inch per turf irrigation event)
- PACE Turf, Shoebox irrigation audit (worked catch-cup example: 0.17 inch in 10 minutes is about 1.02 in/h)
- Hunter Industries, MP Rotator Design Guide (LIT-461): standard MP Rotator nozzles have a matched precipitation rate of approximately 0.4 in/h across a radius of 8 to 35 ft
- Rain Bird, Matched Precipitation Rate (MPR) Nozzles technical spec (full-circle spray nozzles about 1.6 in/h at the optimum 30 psi, higher at low pressure; figure not checked against the full table)
- BrightView, What is the Difference Between Irrigation Sprinkler Heads? (sprays about 1.5 to 2 in/h; rotors and rotary nozzles apply water 2 to 3 times slower); DripWorks gives about 0.4 to 0.8 in/h for rotors. Trade-site ranges, typical figures only
- Virginia Cooperative Extension, Summer Lawn Management: Watering the Lawn (about 1 inch a week from rain or irrigation for most turfgrasses in warm weather; Colorado State Extension gives up to 2.25 inches in hot, dry, windy weather)
- Irrigation Association, Using Distribution Uniformity to Evaluate the Quality of a Sprinkler System (2004): the desired depth is divided by DU; suggested minimum low-quarter DU of 55% for fixed sprays and 70% for rotors (figure not checked against the full document)
- Journal of Irrigation and Drainage Engineering (ASCE), Analysis of Residential Irrigation Distribution Uniformity, 2005, 131(4): a field study that found average low-quarter DU of about 0.45 in homes, below the typical range used here
- University of California, Turfgrass Crop Coefficients (Kc): annual average about 0.80 for cool-season and 0.60 for warm-season turf; turf water use = Kc × ETo
- Texas A&M AgriLife Extension, AGEN-PU-218 Preventing Water Runoff with Cycle and Soak Irrigation (maximum cycle run times by precipitation rate and soil; a 1.5 in/h rate on clay allows about 5 minutes per cycle; table not checked)
- University of Nebraska-Lincoln PASSEL, Irrigation Tables (typical intake rates: clay 0.10 to 0.20, silt loam 0.25 to 0.40, sandy loam 0.35 to 0.50, fine sand 0.50 to 0.75 in/h); USDA NRCS, Infiltration (sands above about 0.8 in/h, clays 0.04 to 0.2); University of Maryland Extension, Table C-3 Soil Infiltration Rates. The figures used here are mid-range typical values
- NIST, Guide for the Use of the International System of Units (SI), appendix B.8: the US liquid gallon is 231 cubic inches
How to work out how long to run a sprinkler zone
- Measure the zone. Enter the length and width of the lawn the zone waters, and take off beds and paving the heads do not water.
- Find the precipitation rate. Use 96.25 × total GPM ÷ area, or run a catch-cup test (average depth ÷ test minutes × 60), or pick a typical rate for your head type.
- Set the weekly need. Start with 1 inch a week including rain, or use ETo × Kc for your weather, and take off the rain that fell.
- Adjust for uniformity. Divide the time by the DU (about 0.55 to 0.75 for home systems) so the driest spots get enough.
- Split by day and soil. Divide the weekly minutes by your watering days, then cut each day into cycles no longer than 60 × soil intake ÷ rate, with at least 30 minutes to soak between them.
Worked examples
| Project | Result |
|---|---|
| 50 × 40 ft rotor zone, 15 GPM, 1 in a week, DU 0.65, loam, 3 days | 128 min of watering per week: 0.72 in/h, 43 min a day in 2 cycles of 21 min, about 1,918 gal |
| 25 × 20 ft spray zone on clay, 8 GPM, DU 0.55, 4 days | 71 min of watering per week: 1.54 in/h, 18 min a day in 4 cycles of 4 min, about 567 gal |
| 40 × 30 ft zone, catch-cup test of 0.3 in in 20 minutes, DU 0.7, loam, 3 days | 95 min of watering per week: 0.9 in/h, 32 min a day in 2 cycles of 16 min, about 1,069 gal |
| 30 × 20 ft sandy zone of MP Rotators (0.4 in/h), DU 0.65, 2 days | 231 min of watering per week: 115 min a day in 2 cycles of 58 min, about 575 gal |
| 60 × 40 ft warm-season lawn, ETo 2 in, Kc 0.6, 0.25 in of rain, 30 GPM, loam | 73 min of watering per week: 0.95 in needed at 1.2 in/h, 24 min a day in 2 cycles, about 2,187 gal |
Frequently asked questions
- How do I calculate the precipitation rate of my sprinklers?
- Precipitation rate in inches per hour = 96.25 × total GPM of the zone ÷ the area it waters in sq ft. The example zone, 15 GPM over 2,000 sq ft, is 0.72 in/h (18.3 mm/h). Or run a catch-cup test: set straight-sided cups across the zone, run it for 15 to 30 minutes, then divide the average depth by the minutes and multiply by 60. 0.9 in/h in the third example comes from 0.3 in in 20 minutes.
- How long should I run my sprinklers to give the lawn 1 inch?
- Divide 60 minutes by the precipitation rate. At 0.72 in/h that is 83 min for a perfectly even system, and 128 min at DU 0.65. Sprays (about 1.75 in/h) take roughly 34 min, MP Rotators (about 0.4 in/h) about 150 min.
- How much water does a lawn need per week?
- About 1 inch a week, rain included, is the usual extension starting point for most lawns in warm weather, and it is the default here. Hot, dry or windy weather can raise it (Colorado State Extension gives up to 2.25 inches for a bluegrass lawn in the hottest weather) and cool or cloudy weather cuts it. To follow the weather, use the evapotranspiration option: turf water use is ETo × Kc.
- What is distribution uniformity and why divide by it?
- Distribution uniformity (DU) is how evenly a zone waters: it compares the driest quarter of the area with the average. If the driest spots get only 65% of the average, you run 1 ÷ 0.65 = 1.54 times as long to give them the full amount. That wastes water on the wetter parts, so fixing tilted heads, bad spacing and pressure is better than running longer. The range 0.55 to 0.75 is typical; a catch-cup test measures yours, and a field study of homes found low-quarter averages near 0.45.
- What is cycle and soak?
- Splitting a watering day into short cycles with time to soak in between, so the water does not run off. When the heads apply water faster than the soil takes it in, the rest puddles and runs to the street. In the example, the rotors put down 0.72 in/h on loam that takes in about 0.4, so the calculator splits the 43 min day into 2 cycles of 21 min. Leave 30 minutes or more between cycles.
- Why does a spray zone on clay need so many cycles?
- Spray heads apply water at 1.5 to 2 in/h and clay takes in around 0.15. The longest cycle is 60 × 0.15 ÷ rate, only about 5 min at 1.75 in/h. The 25 × 20 ft clay example on 8 GPM (1.54 in/h, DU 0.55) needs 71 min a week, which on 4 days is 4 cycles of 4 min each day. Swapping to rotary nozzles ends most of this.
- How many gallons does a sprinkler zone use per week?
- Area × inches × 0.6234 gallons per sq ft per inch, divided by DU for what the zone really puts out. The example needs 1,247 gallons for 1 inch on 2,000 sq ft and uses 1,918 at DU 0.65. A sprinkler running 128 min at 15 GPM puts out the same 1,918 gallons, as a check.
- How do I use evapotranspiration instead of a flat inch?
- Choose Evapotranspiration, enter the week's reference ET (ETo) from your local weather network or extension office, and pick cool- or warm-season grass for Kc (0.8 or 0.6). The warm-season example with 2 in of ETo and 0.25 in of rain needs 2 × 0.6 − 0.25 = 0.95 in, which is 73 min a week.
- Should I water every day for a short time?
- Usually not. Fewer, deeper waterings (often 2 or 3 days a week for an established lawn) grow deeper roots than daily light ones, and cycle and soak lets a slow-absorbing soil take the water without runoff. New seed and sod need frequent light watering until they root. Follow your local watering-day rules, and water early in the morning.
- Can I mix spray heads and rotors on one zone?
- No. Sprays apply water two to three times faster than rotors or rotary nozzles, so a mixed zone drowns one part while the other stays dry, and no run time fits both. Put them on separate zones, or switch the sprays to matched-precipitation rotary nozzles.
Handy tools
- Unit Converter: Switch between gallons and litres, or inches and millimetres, for flow and the depth you want to apply.
- Feet and Inches Calculator: Add up zone sides measured in feet, inches and fractions, and get decimal feet for the length and width.