Drip Irrigation Calculator: Zone Flow, Run Time and Tubing Limits
A 12 × 8 ft bed (96 sq ft) planted 18 in apart holds 40 plants, the same layout as the plant spacing calculator. With 2 emitters of 1 GPH on each plant that is 80 emitters putting out 80 GPH, or 1.33 GPM. One inch a week over the bed is 96 × 0.6234 = 59.8 gallons, and at a drip efficiency of 0.9 that is 66.5 gallons through the emitters, so the answer is 50 min of drip per week (66.5 ÷ 80 GPH = 0.83 hours). On 3 days that is about 17 min a day. The zone draws 1.33 GPM, well inside the 3.75 GPM usable from a spigot that tested at 5 GPM. A typical 1/2 in line carries up to 200 emitters of 1 GPH (200 GPH), and a 1/4 in line up to 30 (30 GPH).
Figures based on the sources listed belowUpdated How we calculate
50 min of drip per week.
50 min of drip per week
- Run time per week: 50 min (0.8 h)
- Run time per watering day: 17 min, 3 days a week
- Zone flow: 80 GPH (1.33 GPM)
- Emitters on the zone: 80 (40 plants x 2)
- Water through the emitters per week: 66.5 gal
- Application rate over the bed: 1.34 in/h (34 mm/h)
- Supply check (bucket test): Fits: the zone draws 1.33 GPM of the 3.75 GPM usable (5 GPM tested)
- 1/2 in tubing (typical): up to 200 emitters of 1 GPH (200 GPH, 200 ft per run); this zone's 80 emitters need 1 run on flow
- 1/4 in tubing (typical): up to 30 emitters of 1 GPH (30 GPH, 30 ft per run); 2 per plant fits on one line
- Longest 1/2 in run (typical limit 200 ft): 100 ft is within 200 ft
Shopping list
- Drip irrigation kit for raised beds
- Pressure regulator and filter for drip (25 psi)
- 1/2 in poly drip tubing (.600 ID)
- Adjustable and fixed drip emitters
- Hose-end timer
- 5 gallon bucket for a flow test
Your project
- Bed or row length × bed or row width: 12 × 8 ft
- Count the plants from: The bed size and plant spacing
- Plant spacing, on center: 18 in
- Emitters per plant: 2
- Emitter flow: 1 GPH
- Weekly water target from: A depth over the bed (inches)
- Water to apply per week: 1 in
- Drip efficiency: 0.90 (typical for drip)
- Watering days per week: 3 days
- Supply flow from a bucket test: 5 GPM
- Share of the tested flow to use: 75% (a cautious margin)
- Longest run of 1/2 in tubing: 100 ft
Also pick up
- Drip irrigation kit for raised beds
- Pressure regulator and filter for drip (25 psi)
- 1/2 in poly drip tubing (.600 ID)
- Adjustable and fixed drip emitters
- Hose-end timer
- 5 gallon bucket for a flow test
Reopen this calculation: /calculators/drip-irrigation/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjoxMiwid2lkdGhGdCI6OH0sImRlZHVjdGlvbnMiOltdLCJ3YXN0ZVBjdCI6MC4xLCJwYXJhbXMiOnsiY291bnRNb2RlIjoxLCJzcGFjaW5nSW4iOjE4LCJwbGFudENvdW50IjozMCwiZW1pdHRlcnNQZXJQbGFudCI6MiwiZW1pdHRlckdwaCI6MSwidGFyZ2V0TW9kZSI6MSwid2Vla2x5RGVwdGhJbiI6MSwiZ2FsUGVyUGxhbnQiOjUsImVmZmljaWVuY3kiOjAuOSwiZGF5c1BlcldlZWsiOjMsInN1cHBseUdwbSI6NSwic3VwcGx5U2hhcmUiOjAuNzUsInJ1bkZ0IjoxMDB9fQ
Show diagram
Saved projects
No saved projects yet.
Typical tubing limits and the most emitters on one run
| Tubing | Max run | Max flow | 0.5 GPH emitters | 1 GPH emitters | 2 GPH emitters |
|---|---|---|---|---|---|
| 1/2 in (0.600 in inside diameter), typical | 200 ft | 200 GPH | 400 | 200 | 100 |
| 1/4 in, typical | 30 ft | 30 GPH | 60 | 30 | 15 |
| 1/2 in (0.700 in outside diameter), DIG ceiling | 350 ft (safe single run) | 220 GPH (3.6 GPM) | 440 | 220 | 110 |
Zone flow by number of emitters
| Emitters | 0.5 GPH each | 1 GPH each | 2 GPH each |
|---|---|---|---|
| 20 emitters | 0.17 GPM (10 GPH) | 0.33 GPM (20 GPH) | 0.67 GPM (40 GPH) |
| 40 emitters | 0.33 GPM (20 GPH) | 0.67 GPM (40 GPH) | 1.33 GPM (80 GPH) |
| 80 emitters | 0.67 GPM (40 GPH) | 1.33 GPM (80 GPH) | 2.67 GPM (160 GPH) |
| 100 emitters | 0.83 GPM (50 GPH) | 1.67 GPM (100 GPH) | 3.33 GPM (200 GPH) |
| 200 emitters | 1.67 GPM (100 GPH) | 3.33 GPM (200 GPH) | 6.67 GPM (400 GPH) |
Water and run time for 1 inch a week by bed size
| Bed area | Plants need | Through emitters | At 1 GPM | At 2 GPM | At 4 GPM |
|---|---|---|---|---|---|
| 25 sq ft | 15.6 gal | 17.3 gal | 17 min | 9 min | 4 min |
| 50 sq ft | 31.2 gal | 34.6 gal | 35 min | 17 min | 9 min |
| 100 sq ft | 62.3 gal | 69.3 gal | 69 min | 35 min | 17 min |
| 200 sq ft | 124.7 gal | 138.5 gal | 139 min | 69 min | 35 min |
| 400 sq ft | 249.4 gal | 277.1 gal | 277 min | 139 min | 69 min |
Bucket test: seconds to fill 5 gallons
| Fill time | Tested flow | Usable (75%) | Emitters at 1 GPH | Emitters at 2 GPH |
|---|---|---|---|---|
| 20 s | 15 GPM | 11.25 GPM | 675 | 1,350 |
| 30 s | 10 GPM | 7.5 GPM | 450 | 900 |
| 45 s | 6.67 GPM | 5 GPM | 300 | 600 |
| 60 s | 5 GPM | 3.75 GPM | 225 | 450 |
| 90 s | 3.33 GPM | 2.5 GPM | 150 | 300 |
| 120 s | 2.5 GPM | 1.88 GPM | 113 | 225 |
Methodology & assumptions
Plants. By default the calculator lays the bed out with the plant spacing calculator's own logic: a square grid, rows along the length, half the spacing kept clear of every edge, and plants = (floor of usable length ÷ spacing + 1) × (floor of usable width ÷ spacing + 1); areas you mark as not planted scale the count by their share. If you already know how many plants are on the zone, choose the entered count instead. For a single row, make the bed 1 ft wide or less. Zone flow. Emitters = plants × emitters per plant, and zone flow in GPH = emitters × the flow of one emitter (0.5, 1 or 2 GPH, the common fixed sizes); GPM = GPH ÷ 60. Inline emitter tubing counts the same way: one emitter per emitter, at its own flow. Water to apply. By depth, the weekly need is area × inches × 0.6234 gallons, the same 144 ÷ 231 constant the sprinkler run time calculator uses; by plant, it is plants × gallons per plant. About 1 inch a week over the bed (0.623 gallons per sq ft) is the usual extension starting point for vegetables in summer, and about half that in cool spring or fall weather; hot, dry or windy weather can need more, and trees and shrubs are better planned by gallons per plant. Efficiency. Drip puts water at the roots with little evaporation or runoff, and extension sources quote efficiencies of 90% or better, against 50 to 70% for sprinklers; the run time divides by 0.9 (an estimate), so 10% more water goes through the emitters than the plants take up. This is not the sprinkler calculator's distribution uniformity of 0.55 to 0.75, because drip has no overlapping spray pattern to even out; a leaking or clogged system scores lower, so the 0.8 setting is there. Run time. Minutes per week = gallons through the emitters ÷ zone GPH × 60, split over the watering days you choose. The application rate over the bed is 1.604 × zone GPH ÷ area in inches per hour; 1.604 is 96.25 ÷ 60, the sprinkler calculator's constant per minute, and Utah State Extension uses the same number. Drip applies at a point, so water spreads sideways and down in the soil and the rate over the bed is an average, not what the soil surface takes in. Sandy soils spread water less sideways, so they want closer emitters or more of them; clay takes it in slowly, so 0.5 GPH emitters and shorter, more frequent runs suit it. Tubing limits. The limits shown are typical design rules, stated as estimates: 1/2 in polyethylene tubing (0.600 in inside diameter) up to 200 ft and 200 GPH in one run, which keeps the water at about 5 ft per second, and 1/4 in tubing up to 30 ft and 30 GPH. The maximum number of emitters is the GPH limit ÷ the emitter flow, rounded down: 400, 200 or 100 emitters (0.5, 1 or 2 GPH) on a 1/2 in run and 60, 30 or 15 on a 1/4 in line. Manufacturers publish higher ceilings for some tubing: DIG gives 220 GPH (3.6 GPM) and about 350 ft as a safe single run for 0.700 in outside diameter tubing at 20 to 40 psi, and a retailer gives 240 GPH for 1/2 in mainline, so stay with the lower rule unless your tubing's data sheet allows more. Inline emitter tubing (dripline) is different: its maximum run depends on the emitter spacing, the emitter flow and the inlet pressure, so use the maker's chart for the exact product (Netafim and Toro publish them) and keep to the pressure range on the label, usually 10 to 60 psi, with a regulator at 25 to 30 psi for most drip fittings. Supply check. Time a 5 gallon bucket at the spigot: GPM = 300 ÷ seconds. The zone's GPM is compared with the usable share of the tested flow (75% by default, an estimate, to leave room for the pressure lost in the filter, regulator, timer and hose); if the zone is over, it is split into the number of zones the supply can run one at a time, ceil(zone GPM ÷ usable GPM). Not modelled: pressure and friction loss along the line (a hydraulic design needs the pipe diameter, length and fittings), elevation change, emitter clogging, rain, ET, soil water holding capacity and root depth, and watering restrictions. Metric: lengths and depths follow the switch, flow stays in GPH and GPM next to the litre amounts.
- DIG Corporation, The drip irrigation guide (DIG_Drip-Irrigation-Guide): the maximum flow for 0.700 in OD poly tubing is 220 GPH (3.6 GPM) at up to 60 psi, and the emitters on a line should not add up to more (figure not checked against the full document)
- DIG Corporation, polyethylene supply tubing technical note (2016/2018): operate between 20 and 40 psi; about 350 ft is a safe maximum single run (figure not checked against the full document)
- UC Master Gardeners (ucanr.edu network), drip irrigation article: the "30/30 rule" for 1/4 in line, no more than 30 ft in a run and 30 GPH, because longer runs lose too much to friction (figure not checked against the full document)
- Drip Depot, Drip Irrigation General System Checklist: 1/4 in tubing no more than 30 ft and 30 GPH; 1/2 in tubing no more than 200 ft and 200 GPH. Drip Depot, Friction Loss Explained: 200 GPH in 1/2 in (0.600 in ID) tubing is about 5 ft per second. A retailer, so typical rules (figure not checked against the full document)
- DripWorks, Pipe Sizing Chart Guide: a retailer figure of about 240 GPH for 1/2 in mainline, higher than the 200 GPH rule used here (figure not checked against the full document)
- Rain Bird, 1/4" Drip Distribution Tubing and 1/2" Drip Distribution Tubing product pages: 1/4 in tubing is about 0.25 in OD and 0.17 in ID with 25 to 30 psi recommended; spot emitters come in 1.0 and 2.0 GPH. Rain Bird publishes no run length for plain tubing on these pages, so the limits are the typical rules above
- Toro, Blue Stripe drip product sheet, and Netafim, Techline CV specification (pressure compensating from 14.5 to 58 psi): both publish maximum run length charts by emitter flow, spacing and inlet pressure for dripline; use them for dripline runs (not checked in full)
- University of California Master Gardener Program of Sonoma County, Drip Irrigation: drip exceeds 90% efficiency, against 50 to 70% for sprinklers and hand watering; about 1 inch a week over a vegetable bed in summer, which is 0.623 gallons per sq ft (a 32 sq ft bed needs about 20 gallons)
- Colorado State University Extension, Drip Irrigation for Home Gardens (4.702): drip is more than 90% efficient, sprinklers 50 to 70%
- Utah State University Extension, Water Recommendations for Vegetables: inches per hour = emitters × GPH × 1.604 ÷ area in sq ft (1.604 = 12 ÷ 7.48)
- Penn State Extension, Determining How Long to Run Drip Irrigation Systems for Vegetables: run time from the weekly depth and the system flow, split into events that suit the soil (figure not checked against the full document)
- Alabama Cooperative Extension System, Tools of the Trade: Measuring Water Flow Rate (the bucket method: gallons ÷ minutes); California State Water Resources Control Board, flow measurement by timing a fill (repeat three times and average)
- The plant spacing and sprinkler run time calculators on this site: the bed layout, 0.6234 gallons per sq ft per inch (144 ÷ 231) and 96.25 inches-per-hour constant are theirs
- NIST, Guide for the Use of the International System of Units (SI), appendix B.8: the US liquid gallon is 231 cubic inches
How to size a drip irrigation zone
- Count the plants. Enter the bed length and width and the plant spacing, or enter the number of plants if you know it.
- Choose the emitters. Pick how many emitters each plant gets and the flow of each (0.5, 1 or 2 GPH), then read the zone flow in GPH and GPM.
- Set the weekly water. Use about 1 inch a week over the bed for vegetables, or gallons per plant for shrubs, and keep the 0.9 efficiency allowance.
- Read the run time. The weekly minutes are the gallons through the emitters divided by the zone GPH; split them over your watering days.
- Check the tubing and the supply. Keep each 1/2 in run under about 200 ft and 200 GPH and each 1/4 in line under 30 ft and 30 GPH, and compare the zone GPM with the usable share of your bucket-test flow, splitting the bed into zones if it is over.
Worked examples
| Project | Result |
|---|---|
| 12 × 8 ft bed at 18 in, 2 emitters of 1 GPH per plant, 1 in a week, 3 days, 5 GPM supply | 50 min of drip per week: 40 plants, 80 GPH (1.33 GPM), 17 min a day, about 66 gal |
| 20 ft row of 10 tomatoes, 2 emitters of 2 GPH each, 10 gallons per plant a week, 3 days | 167 min of drip per week: 40 GPH (0.67 GPM), 56 min a day, about 111 gal |
| 25 ft row of lettuce at 12 in, one 0.5 GPH emitter each (clay), 1 in a week, 2 days | 83 min of drip per week: 25 plants, 12.5 GPH (0.21 GPM), 42 min a day, about 17 gal |
| 30 × 10 ft bed at 18 in, 2 emitters of 2 GPH per plant, 5 GPM supply at 75% | 26 min of drip per week: 120 plants, 480 GPH (8 GPM), over the 3.75 GPM usable, so 3 zones |
Frequently asked questions
- How do I calculate the flow of a drip zone?
- Multiply the number of emitters by the flow of each one. The example bed has 40 plants with 2 emitters of 1 GPH each, so 80 × 1 = 80 GPH, which is 80 ÷ 60 = 1.33 GPM. That figure must fit inside what your spigot can supply and what the tubing can carry.
- How long should I run drip irrigation?
- Gallons needed ÷ zone GPH. One inch a week on the 96 sq ft example bed is 59.8 gallons, 66.5 with the 0.9 efficiency allowance, and the zone delivers 80 GPH, so about 50 min a week. Spread over 3 days that is 17 min each day. If you plan by plant instead, 10 tomato plants at 10 gallons each on 2 emitters of 2 GPH run 167 min a week.
- How many emitters can I put on 1/2 inch tubing?
- The usual rule is no more than 200 GPH and 200 ft on a run of 1/2 in tubing, which is 400 emitters of 0.5 GPH, 200 of 1 GPH or 100 of 2 GPH. DIG gives a higher ceiling of 220 GPH for 0.700 in OD tubing, and some retailers quote 240 GPH, so 200 is the cautious figure. These are typical limits; past them the emitters at the far end get less water.
- How many emitters can I put on 1/4 inch tubing?
- The common rule for 1/4 in tubing is 30 ft and 30 GPH, which is 60 emitters of 0.5 GPH, 30 of 1 GPH or 15 of 2 GPH. In practice 1/4 in line is used for short branches from the 1/2 in line to individual plants, with one to four emitters on each, which is far below the limit.
- How do I know if my faucet can run the zone?
- Do a bucket test: time how long the spigot takes to fill a 5 gallon bucket with nothing else running, and divide 300 by the seconds (47 seconds is 6.4 GPM). Enter that flow. The calculator uses 75% of it as usable, because the filter, regulator, timer and hose take some of it, and compares it with the zone. A bed that is over is split into zones that run one after another: the 30 × 10 ft example with 2 GPH emitters draws 8 GPM against 3.75 usable, so it needs 3 zones.
- Which emitter flow should I use: 0.5, 1 or 2 GPH?
- Slower emitters suit clay, which takes in water slowly and puddles under fast ones. 1 or 2 GPH suits loam and sand, where water moves down quickly and needs to spread sideways. For the same weekly gallons, a 2 GPH emitter runs a quarter of the time of a 0.5 GPH one and draws four times the flow: the 25 ft lettuce row at 0.5 GPH needs 83 min a week on 25 emitters, with a zone flow of only 0.21 GPM.
- Why is drip efficiency 0.9 and not the DU the sprinkler calculator uses?
- Sprinklers throw water over the whole area and the overlap is uneven, so the driest spots set the run time and the sprinkler calculator divides by a distribution uniformity of about 0.55 to 0.75. Drip puts the water at the plant, so extension sources quote efficiencies of 90% or better, against 50 to 70% for sprinklers. The 0.9 is a typical figure; pick 0.8 for an old or leaking system.
- How much water do garden beds need per week?
- About 1 inch over the bed per week is the usual start for vegetables in summer, which is 0.623 gallons per sq ft, and about half that in cool spring or fall weather. Hot, dry or windy weather can need more, and your own soil, plant size and rain change it. Take off rain that soaked in, or choose gallons per plant for shrubs and trees.
- What application rate does drip give?
- Zone GPH × 1.604 ÷ area, in inches per hour. The example puts 80 GPH over 96 sq ft: 80 × 1.6 ÷ 96 = 1.34 in/h. That is an average over the whole bed; the water really goes in at the emitters and spreads through the soil from there, so the rate under an emitter is far higher than the average and the soil, not this figure, sets how fast an emitter can run without puddling.
- Can I rain-barrel water for drip irrigation?
- Yes, but a barrel on the ground gives very little pressure, so most drip fittings and emitters need a small pump or a barrel raised high, and pressure-compensating emitters have a minimum working pressure printed on the package. Use the rainwater harvesting calculator to see how many gallons a roof collects against the weekly gallons here.
Handy tools
- Unit Converter: Switch between gallons per hour and per minute, gallons and litres, or inches and millimetres.
- Feet and Inches Calculator: Add up bed sides and tubing runs measured in feet, inches and fractions, and get decimal feet for the fields.