Roof Underlayment Calculator: How Many Rolls Do I Need?
A 40 × 30 ft house with a 12 in overhang and a 6/12 gable roof has 1,503 sq ft of roof. It needs 4 rolls of #15 felt (4 squares a roll) with 5% waste, once ice-and-water shield along both eaves (40 in up the slope, 282 sq ft, 3 rolls of membrane) takes over the lowest 282 sq ft and the felt covers the other 1,221 sq ft. At 2/12 up to 4/12 the code asks for two layers, which roughly doubles the felt.
Figures based on the sources listed belowUpdated How we calculate
Buy 4 rolls.
Buy 4 rolls
1,220.89 sq ft + 5% waste = 1,281.94 sq ft
- Roof area (before the ice barrier and laps): 16 squares (≈ 1,503 sq ft)
- Layers of underlayment: 1 layer
- Ice-and-water membrane (36 in × 66.7 ft rolls): 3 rolls (≈ 168 ft), 2 courses along the eaves
- Eave ice barrier strip (to 24 in inside the wall): 282 sq ft (≈ 84 ft)
Low
$80.00
Expected
$128.00
High
$200.00
Includes 61.04 sq ft waste
How this number is calculated
1,220.89 sq ft + 5% waste = 1,281.94 sq ft ÷ 400 sq ft per roll = 4 rolls
Shopping list
- Synthetic roof underlayment (10 square roll)
- Ice and water shield roll
- Plastic cap nails for underlayment
- Cap staples for underlayment
- Utility knife with hook blades
- Chalk line
- Roof harness and rope grab kit
- Roofing cement sealant
Your project
- Building length × building width: 40 × 30 ft
- Roof pitch (rise per 12 in of run, x/12): 6
- Roof shape: Gable: two sloping sides
- Overhang: 12 in
- Underlayment: #15 felt (4 squares a roll)
- Ice barrier along the eaves: Yes: eave to 24 in inside the wall
- Valley length (ice-and-water in valleys): 0 ft
- Waste: Simple gable roof (5%)
Also pick up
- Synthetic roof underlayment (10 square roll)
- Ice and water shield roll
- Plastic cap nails for underlayment
- Cap staples for underlayment
- Utility knife with hook blades
- Chalk line
- Roof harness and rope grab kit
- Roofing cement sealant
Reopen this calculation: /calculators/roof-underlayment/?s=eyJyb29tIjp7Imxlbmd0aEZ0Ijo0MCwid2lkdGhGdCI6MzB9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMDUsInBhcmFtcyI6eyJwaXRjaCI6Niwic2hhcGUiOjAsIm92ZXJoYW5nSW4iOjEyLCJyb2xsVHlwZSI6MSwiaWNlRWF2ZXMiOjEsInZhbGxleUZ0IjowfX0
Show diagram
Saved projects
No saved projects yet.
Rolls of underlayment by roll type and roof area
| Underlayment | Net coverage per roll | 1,000 sq ft of roof | 1,500 sq ft of roof | 2,000 sq ft of roof | 3,000 sq ft of roof |
|---|---|---|---|---|---|
| #15 felt | 400 sq ft | 3 | 4 | 6 | 8 |
| #30 felt | 200 sq ft | 6 | 8 | 11 | 16 |
| synthetic (GAF, 48 in) | 938 sq ft | 2 | 2 | 3 | 4 |
| synthetic (Owens Corning, 42 in) | 929 sq ft | 2 | 2 | 3 | 4 |
Eave ice barrier by overhang and pitch
| Overhang | 4/12 pitch | 6/12 pitch | 8/12 pitch | 12/12 pitch |
|---|---|---|---|---|
| No overhang | 25 in, 2 rolls | 27 in, 2 rolls | 29 in, 2 rolls | 34 in, 2 rolls |
| 12 in overhang | 38 in, 3 rolls | 40 in, 3 rolls | 43 in, 3 rolls | 51 in, 3 rolls |
| 18 in overhang | 44 in, 3 rolls | 47 in, 3 rolls | 50 in, 3 rolls | 59 in, 3 rolls |
| 24 in overhang | 51 in, 3 rolls | 54 in, 3 rolls | 58 in, 3 rolls | 68 in, 3 rolls |
Layers and laps by roof slope (asphalt shingles)
| Roof slope | Underlayment | Laps |
|---|---|---|
| 4:12 and steeper | One layer, shingle fashion from the eave up | 2 in side laps, 4 in end laps offset 6 ft |
| 2:12 up to but not including 4:12 | Two layers (double coverage) | Lapped half the sheet width plus 2 in; 19 in over a 36 in felt sheet |
| Under 2:12 | Not an ordinary shingle slope | Ask the shingle maker and your building department |
| Eaves, where ice forms | Ice barrier: self-adhering membrane, or two cemented layers | Eave edge to 24 in inside the exterior wall line |
Roll sizes and coverage used here
| Item | Roll | Coverage used |
|---|---|---|
| #15 felt | 36 in × 144 ft (432 sq ft gross) | 4 squares (400 sq ft) |
| #30 felt | 36 in × 72 ft (216 sq ft gross) | 2 squares (200 sq ft) |
| Synthetic: GAF FeltBuster or Deck-Armor | 48 in × 250 ft, 10 squares excluding laps | 938 sq ft with a 3 in side lap |
| Synthetic: Owens Corning ProArmor | 42 in × 286 ft, 10 squares excluding laps | 929 sq ft with a 3 in side lap |
| Ice-and-water shield (GAF StormGuard) | 36 in × 66.7 ft, 2 squares gross | One roll covers 66.2 ft of one course after the end lap |
Methodology & assumptions
The roof area uses the same model as the roofing shingles calculator: the footprint (length × width) plus the overhang on every side, times the pitch factor √(1 + (rise ÷ 12)²). Layers: asphalt-shingle roofs need one layer of underlayment at 4:12 and steeper and two layers from 2:12 up to but not including 4:12 (IRC R905.1.1 and R905.2.7, and GAF's low-slope guidance); the calculator doubles the area in that band, and the code's lapped method (a half-width starter strip, then each sheet lapped half its width plus 2 in) comes out close to that, so treat it as an estimate. Below 2:12 it counts one layer and flags it, because ordinary shingle methods do not apply there. Ice barrier: IRC R905.1.2 asks for self-adhering membrane (or two cemented layers) from the lowest edge of the roof to 24 in inside the exterior wall line, in places where ice has formed along the eaves. That distance is horizontal, so the strip on the roof is (overhang + 24 in) × the pitch factor wide, along every eave (both long sides of a gable roof, the whole perimeter of a hip roof). Membrane comes in 36 in × 66.7 ft rolls (GAF StormGuard, 2 squares gross); a strip wider than one roll takes extra courses lapped 3.5 in at the side, and each roll gives up 6 in at the end lap (Grace Ice & Water Shield minimums, a typical figure: check your roll). The membrane replaces the underlayment under it, so the strip's area comes off the underlayment. Valleys get one 36 in wide course each, a common practice and an estimate; enter the total valley length. Roll coverage: felt is sold by net coverage, about 4 squares (400 sq ft) for #15 and 2 squares (200 sq ft) for #30, with laps allowed for; synthetic rolls are quoted at 1,000 sq ft before laps, so the calculator takes off the side lap: 48 in rolls with a 3 in lap cover about 938 sq ft and Owens Corning's 42 in ProArmor about 929 sq ft (the maker lists 929). Rolls = underlayment area × layers × (1 + waste) ÷ the roll's net coverage, rounded up; waste is not added to the ice-and-water. The 4 in end laps the code asks for (offset 6 ft) are small on a 144 ft felt roll or 250 ft synthetic roll and are taken as covered by the waste. Drip edge, fasteners, valleys beyond the length you enter, penetrations and flashing are not counted. The metric toggle shows lengths in m and the roof area in m².
- GAF Deck-Armor Premium Breathable Roof Deck Protection sell sheet (RESUL164): roll size 10 squares (1,000 sq ft), excluding laps
- GAF FeltBuster High-Traction Synthetic Roofing Felt product data and installation instructions: 10 squares per roll (48 in × 250 ft), excluding laps; 3 in side lap
- Owens Corning ProArmor synthetic roof underlayment product page: 42 in × 286 ft roll, 10 squares, 929 sq ft with a 3 in overlap
- GAF StormGuard Film-Surfaced Leak Barrier technical data sheet and installation instructions (RESUL192): 36 in × 66.7 ft roll, gross coverage 2 squares (200 sq ft)
- G.A.P. #15 asphalt felt roofing underlayment, ASTM D226: about 4 squares (400 sq ft) per roll
- Warrior Roofing #15 felt, 432 sq ft roll (36 in × 144 ft gross), sold as 4 squares
- No. 30 asphalt felt, ASTM D226 product data (Allied): 36 in roll; #30 felt is sold as 2 squares (200 sq ft) a roll
- International Residential Code, Chapter 9 Roof Assemblies: R905.1.1 underlayment (two layers from 2:12 to under 4:12 under asphalt shingles), R905.2.7 application (2 in side laps, 4 in end laps offset 6 ft) and R905.1.2 ice barrier (eave to 24 in inside the exterior wall line); numbering and wording vary by edition, so check the one your jurisdiction adopted (2021 edition)
- International Residential Code 2024, Chapter 9 Roof Assemblies (current edition; the 2018 text added a further 36 in rule at 8:12 and steeper, which later editions are reported to have dropped; check the edition your area has adopted)
- GAF, Minimum slope for shingles: what contractors need to know: low slope is 2:12 up to but not including 4:12 and needs a double layer of roof deck protection
- Fine Homebuilding, Ice barriers explained: how far up the roof slope (the 24 in rule is measured horizontally from the wall line)
- Grace Ice & Water Shield product data: side laps at least 3.5 in and end laps at least 6 in (used for the membrane laps)
- GAF, The benefits of installing ice and water shields in roof valleys (valleys are a recommended location; the 36 in valley strip is a typical estimate)
- Typical US retail prices per roll of felt, synthetic underlayment and ice-and-water shield, 2026 (estimate)
How to calculate roof underlayment
- Get the true roof area. Measure the building and overhang, then multiply the footprint by the pitch factor √(1 + (rise ÷ 12)²) and take off skylights and chimneys.
- Decide on layers. Use one layer at 4:12 and steeper, two layers from 2:12 up to but not including 4:12 under asphalt shingles.
- Size the ice barrier. Where the code requires it, run self-adhering membrane from the eave to 24 in inside the exterior wall line, measured level, and add one 36 in course along each valley. Count the rolls and take the eave strip off the underlayment area.
- Convert to rolls. Multiply the remaining area by the layers and by 1 plus the waste, then divide by the roll's net coverage (about 400 sq ft for #15 felt, 200 for #30, 929 to 938 for synthetic) and round up.
Worked examples
| Project | Result |
|---|---|
| 40 × 30 ft house, gable roof, 6/12 pitch, 12 in overhang, ice barrier at the eaves, #15 felt, 5% waste | 4 rolls of #15 felt, 3 rolls of ice-and-water shield (1,503 sq ft of roof) |
| 40 × 30 ft house, gable roof, 3/12 pitch, 12 in overhang, #30 felt, no ice barrier, 5% waste (low slope: two layers) | 15 rolls of #30 felt (2 layers over 1,385 sq ft of roof) |
| 50 × 30 ft house, hip roof, 8/12 pitch, 12 in overhang, 40 ft of valleys, ice barrier at the eaves, GAF synthetic, 10% waste | 2 rolls of synthetic and 6 rolls of ice-and-water shield (2,000 sq ft of roof) |
| 28 × 16 ft garage, gable roof, 4/12 pitch, 12 in overhang, one 2 × 4 ft skylight, Owens Corning synthetic, no ice barrier, 5% waste | 1 roll of synthetic (561 sq ft to cover after the skylight) |
Frequently asked questions
- How many squares are in a roll of felt?
- A roll of #15 felt is sold as 4 squares (about 400 sq ft) and a roll of #30 felt as 2 squares (about 200 sq ft). Those are net figures with laps already allowed for: a 36 in × 144 ft roll of #15 is 432 sq ft gross. #30 is heavier, so the roll is shorter. Labels vary a little by maker, so read the one on your roll.
- How much does a roll of synthetic underlayment cover?
- Most synthetic rolls are sold as 10 squares, 1,000 sq ft, before laps: GAF FeltBuster and Deck-Armor are 48 in × 250 ft and Owens Corning ProArmor is 42 in × 286 ft. With a 3 in side lap a GAF roll covers about 938 sq ft and Owens Corning gives 929 sq ft on its own page. The calculator uses those net figures.
- Do I need two layers of underlayment on a low slope?
- Under asphalt shingles, yes, for slopes from 2:12 up to but not including 4:12: the IRC asks for two layers (R905.1.1), and GAF says the same for its shingles. At 4:12 and steeper one layer is enough. The calculator doubles the area when the pitch is in that band. Below 2:12 shingles are not an ordinary choice, so ask the shingle maker and your building department.
- How far up the roof does ice-and-water shield go?
- IRC R905.1.2 runs the ice barrier from the lowest edge of the roof to a point at least 24 in inside the exterior wall line, measured horizontally. With a 12 in overhang and a 6/12 pitch that is (12 + 24) in × 1.118 = 40 in up the slope, more than one 36 in roll, so it takes two courses. Check whether your area requires it: it is aimed at places where ice backs up at the eaves.
- Do I subtract the ice-and-water area from the underlayment?
- Yes. Self-adhering membrane is used in place of the underlayment where it goes, so the calculator takes the eave strip (282 sq ft in the example) off the underlayment area. Run the underlayment up and over the top edge of the membrane, as the shingle maker's instructions describe. Valleys are counted in membrane only.
- How much overlap should I allow?
- The IRC asks for 2 in side laps and 4 in end laps, with end laps offset 6 ft, for one layer under asphalt shingles; synthetic makers usually ask for more, such as 3 in at the side for GAF and Owens Corning. The calculator builds those into the roll coverage and adds waste on top. Follow the instructions of the product you buy if they ask for more.
- How much waste should I allow for underlayment?
- About 5% for a plain gable roof and 10% for a hip roof or one with many valleys and dormers, since each cut leaves an offcut that is rarely worth reusing. Both are presets here. Underlayment waste is small compared with shingles because the roll is cut to length and laps are already counted.
- Should I use felt or synthetic underlayment?
- Both are code-accepted under asphalt shingles when they meet the standard the code lists. Synthetic rolls cover more (10 squares against 4 or 2), are lighter per square and tear less, but cost several times as much per roll. #30 felt is heavier and costs more than #15 but is stiffer and lays flatter. Check what your shingle maker and warranty accept.
- Does this count the felt under metal roofing or tile?
- The roof area and rolls apply to any roof, but the layers rule here is for asphalt shingles. Metal and tile makers often call for their own underlayment, such as high-temperature synthetic under metal, so read their instructions; the metal roofing calculator counts the panels.