Roof Pitch Calculator: Pitch, Angle, Slope and Roof Area
A roof that rises 6 in over a 12 in run is a 6:12 pitch, 26.57°, 50.0% slope, multiplier 1.118. On a 40 × 30 ft house with a 12 in overhang that is 42 × 32 = 1,344 sq ft of footprint, so the sloping surface is 1,503 sq ft (15 squares): the footprint times the multiplier 1.118. Pitch is the rise in inches for every 12 in of run, so 6:12 is also written 6/12 and spoken "six-twelve". Asphalt shingles need at least 2:12 under the IRC, with two layers of underlayment below 4:12.
Figures based on the sources listed belowUpdated How we calculate
6:12 pitch, 26.57°, 50.0% slope, multiplier 1.118.
6:12 pitch, 26.57°, 50.0% slope, multiplier 1.118
- Pitch (rise per 12 in of run): 6:12
- Angle: 26.57°
- Slope (rise ÷ run): 50.0%
- Pitch multiplier (rafter length factor): 1.118, multiply a run by this for the length along the slope
- Roof area (footprint with overhang × multiplier): 1,503 sq ft
- Roofing squares (100 sq ft each): 15.0
- Asphalt shingles (IRC R905.2.2): 4:12 or more, shingles with the normal single layer of underlayment
- Metal panels and membranes (IRC R905): 3:12 or more, lapped exposed-fastener metal panels allowed without lap sealant
Shopping list
- Digital angle finder or level
- Speed square (rafter square)
- Pitch gauge / roof slope finder
- Tape measure, 25 ft
- Laser distance measurer
- Roof harness and rope grab kit
Your project
- Building length × building width: 40 × 30 ft
- I know the slope as: Rise and run
- Rise: 6 in
- Run: 12 in
- Overhang: 12 in
Also pick up
- Digital angle finder or level
- Speed square (rafter square)
- Pitch gauge / roof slope finder
- Tape measure, 25 ft
- Laser distance measurer
- Roof harness and rope grab kit
Reopen this calculation: /calculators/roof-pitch/?s=eyJyb29tIjp7Imxlbmd0aEZ0Ijo0MCwid2lkdGhGdCI6MzB9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMSwicGFyYW1zIjp7Im1vZGUiOjAsInJpc2VJbiI6NiwicnVuSW4iOjEyLCJzcGFuUmlzZUluIjo3Miwic3BhbkluIjoyODgsImFuZ2xlRGVnIjoyNi41Nywib3ZlcmhhbmdJbiI6MTJ9fQ
Show diagram
Saved projects
No saved projects yet.
Roof pitch table: 1:12 to 18:12
| Pitch | Angle | Slope % | Multiplier | Roofing note |
|---|---|---|---|---|
| 1:12 | 4.76° | 8.3% | 1.003 | Low-slope roofing only |
| 2:12 | 9.46° | 16.7% | 1.014 | Shingles with two layers of underlayment; lapped metal needs sealant |
| 3:12 | 14.04° | 25.0% | 1.031 | Shingles with two layers of underlayment |
| 4:12 | 18.43° | 33.3% | 1.054 | Single layer of shingle underlayment |
| 5:12 | 22.62° | 41.7% | 1.083 | Single layer of shingle underlayment |
| 6:12 | 26.57° | 50.0% | 1.118 | Single layer of shingle underlayment |
| 7:12 | 30.26° | 58.3% | 1.158 | Single layer of shingle underlayment |
| 8:12 | 33.69° | 66.7% | 1.202 | Single layer of shingle underlayment |
| 9:12 | 36.87° | 75.0% | 1.250 | Single layer of shingle underlayment |
| 10:12 | 39.81° | 83.3% | 1.302 | Single layer of shingle underlayment |
| 11:12 | 42.51° | 91.7% | 1.357 | Single layer of shingle underlayment |
| 12:12 | 45.00° | 100.0% | 1.414 | Single layer of shingle underlayment |
| 13:12 | 47.29° | 108.3% | 1.474 | Steep: fall protection and extra fastening |
| 14:12 | 49.40° | 116.7% | 1.537 | Steep: fall protection and extra fastening |
| 15:12 | 51.34° | 125.0% | 1.601 | Steep: fall protection and extra fastening |
| 16:12 | 53.13° | 133.3% | 1.667 | Steep: fall protection and extra fastening |
| 17:12 | 54.78° | 141.7% | 1.734 | Steep: fall protection and extra fastening |
| 18:12 | 56.31° | 150.0% | 1.803 | Steep: fall protection and extra fastening |
Minimum roof slopes in the IRC
| Roof covering | Minimum slope | Note |
|---|---|---|
| Asphalt shingles (R905.2.2) | 2:12 (17%) | Two layers of underlayment from 2:12 up to under 4:12 (R905.1.1) |
| Lapped metal panels, no lap sealant (R905.10.2) | 3:12 (25%) | Exposed-fastener panels with non-soldered seams |
| Lapped metal panels with lap sealant (R905.10.2) | 1/2:12 (4%) | Sealant applied to the maker’s instructions |
| Standing-seam metal (R905.10.2) | 1/4:12 (2%) | Check the panel maker for its own minimum |
| Built-up, modified bitumen and single-ply membrane (R905.9, R905.11, R905.12) | 1/4:12 (2%) | Coal-tar built-up roofs 1/8:12 (1%); a design slope for drainage |
Methodology & assumptions
Pick how you know the slope. With rise and run, the pitch is rise ÷ run × 12, the rise in inches per 12 in of run; any unit works if both use the same one. With rise and span, for a symmetric gable, the run is half the span, so the pitch is rise ÷ (span ÷ 2) × 12. With an angle, the pitch is 12 × tan(angle). From the pitch, the angle is atan(pitch ÷ 12), the slope percent is pitch ÷ 12 × 100, and the pitch multiplier (also called the rafter length factor, slope factor or pitch factor) is √(1 + (pitch ÷ 12)²), the length along the slope for each unit of run. The roof area is the footprint, with the overhang added on every side, times the multiplier. It holds for a gable or hip roof when every plane has the same pitch, and it is the same model as the roofing shingles calculator, so the two agree; skylight and chimney openings come off the sloping area. A square is 100 sq ft of roof. The pitch table is worked with the same formulas. The code minimums come from the International Residential Code: asphalt shingles on slopes of 2:12 or more (R905.2.2), with two layers of underlayment from 2:12 up to under 4:12 (R905.1.1), lapped exposed-fastener metal panels without lap sealant on 3:12 or more, with standing seam at 1/4:12 and lapped panels with lap sealant at 1/2:12 (R905.10.2), and built-up, modified bitumen and single-ply membrane roofs at 1/4:12 for drainage (R905.9, R905.11, R905.12). Section numbers and wording differ between code editions, local codes amend them, and a manufacturer's instructions can ask for more, so check your adopted code and the product's instructions. This calculator does not size rafters or judge whether a roof is safe to walk on.
- International Residential Code (ICC), R905.2.2 Slope (asphalt shingles: 2 units vertical in 12 horizontal, 2:12, or greater) and the underlayment application rule for slopes from 2:12 up to 4:12 (two layers). Figures as quoted in the 2018 IRC reroof requirements page of Firestone, Colorado; confirm against the original and the edition your area adopted
- LSU AgCenter, Code-Compliant Roofing Installation (publication 3104): asphalt shingles only on slopes of 2:12 or greater, with double underlayment for 2:12 to 4:12. Figures as quoted from the page; confirm against the original
- Florida Building Commission, Binding Interpretation 231, quoting the IRC-based minimum slopes for metal roof panels: 3:12 for lapped, non-soldered seams without lap sealant, 1/2:12 with applied lap sealant, 1/4:12 for standing seam. Figures as quoted from the page; confirm against the original
- California Residential Code (based on the IRC), Chapter 9 Roof Assemblies, R905 Requirements for roof coverings: built-up and modified bitumen roofs at a design slope of at least 1/4:12 (coal-tar built-up 1/8:12). Figures as quoted from the page; confirm against the original
- Pitch multiplier √(1 + (rise ÷ 12)²): the slope length for each unit of horizontal run (the Pythagorean theorem), as used in framing guides and rafter tables
How to find your roof pitch and roof area
- Measure the slope. Measure the rise over a known run (a level held out 12 in, or a vertical rise over half the span from the attic), or read the angle with a digital angle finder.
- Enter the slope. Pick rise and run, rise and span or angle, and type the measurements in the same unit.
- Read the pitch. The calculator gives the pitch as x:12, the angle, the slope percent and the pitch multiplier.
- Enter the footprint. Type the building length and width and the overhang. The roof area is the footprint with the overhang times the multiplier.
- Check the roofing rules. Compare the pitch with the minimum slopes for your roofing: 2:12 for shingles, 3:12 for lapped exposed-fastener metal, and your local code and the product instructions.
Worked examples
| Project | Result |
|---|---|
| 40 × 30 ft house, 12 in overhang, 6 in rise over a 12 in run | 6:12 pitch, 26.57°, 50.0% slope, multiplier 1.118; 1,503 sq ft of roof (15 squares) |
| 36 × 24 ft gable house, 12 in overhang, ridge 84 in above the eave line over a 288 in (24 ft) span | 7:12 pitch, 30.26°, 58.3% slope, multiplier 1.158; 1,144 sq ft of roof (11.4 squares) |
| 32 × 22 ft house, 12 in overhang, roof angle read as 30 degrees | 6.93:12 pitch, 30.00°, 57.7% slope, multiplier 1.155; 942 sq ft of roof (9.4 squares) |
| 28 × 16 ft garage, 12 in overhang, 3 in rise over a 12 in run, one 2 × 4 ft skylight | 3:12 pitch, 14.04°, 25.0% slope, multiplier 1.031; 549 sq ft of roof after the skylight (5.5 squares). 3:12: 2:12 to under 4:12, shingles allowed with two layers of underlayment; 3:12 or more, lapped exposed-fastener metal panels allowed without lap sealant |
Frequently asked questions
- How do I calculate roof pitch?
- Divide the rise by the run and multiply by 12. A roof that rises 6 in over a 12 in run is 6:12. If you measured a different run, the same rule applies: 7:12 comes from an 84 in rise over a 144 in run (half of a 24 ft span). The calculator takes rise and run, rise and span or an angle and gives the pitch as x:12.
- How do I measure roof pitch?
- Hold a level horizontally against the roof, mark 12 in along it from the roof, and measure straight down from that mark to the roof; that reading is the rise per 12. From the attic, measure along a rafter instead: the vertical drop over a level 12 in is the same number. A digital angle finder laid on the roof gives the angle, which this calculator also accepts. Working on a roof needs fall protection; measure from a ladder or the attic where you can.
- What is the pitch multiplier?
- The pitch multiplier, also called the rafter length factor, slope factor or pitch factor, is √(1 + (pitch ÷ 12)²). Multiply a horizontal run by it to get the length along the slope, or a footprint by it to get the roof area. At 6:12 it is 1.118, at 12:12 it is 1.414. The table on this page lists 1:12 to 18:12.
- How do I turn a pitch into degrees?
- The angle is the arctangent of pitch ÷ 12. A 6:12 roof is 26.57°, 12:12 is exactly 45°, and a 4:12 roof is 18.43°. Going the other way, the pitch is 12 × tan(angle): 6.93:12 for 30°.
- What is the slope percent of a 6:12 roof?
- 50.0%. Slope percent is rise ÷ run × 100, so 6 ÷ 12 is 50%. Percent is not the same as degrees: a 100% slope is 45°, not 100°. A 4:12 roof is 33.3%.
- What is the minimum roof pitch for asphalt shingles?
- The International Residential Code (R905.2.2) allows asphalt shingles on slopes of 2:12 (about 17%) or more. From 2:12 up to under 4:12 the code calls for two layers of underlayment instead of one (R905.1.1), and many shingle makers and roofers suggest 4:12 or more for good drainage. Below 2:12 use a low-slope roofing system. Section numbers and wording differ by edition, local codes amend them, and the shingle maker’s instructions can require more.
- What is the minimum pitch for a metal roof?
- In the IRC (R905.10.2), lapped, exposed-fastener metal panels without lap sealant need 3:12 (25%); with lap sealant applied to the maker’s instructions the minimum drops to 1/2:12; standing-seam systems are allowed at 1/4:12. Panel makers often set their own minimums, so check the product data sheet.
- What is a low-slope roof?
- Codes treat slopes below 2:12 as low-slope and need roofing made for it, such as built-up, modified bitumen or single-ply membrane roofs, which the IRC allows down to a design slope of 1/4:12 for drainage (1/8:12 for coal-tar built-up). Shingles are not allowed there.
- How do I find the roof area from the pitch?
- Add the overhang to the building length and width, multiply them for the footprint, and multiply by the pitch multiplier. The 40 × 30 ft example has a 12 in overhang, so 42 × 32 = 1,344 sq ft times 1.118 is 1,503 sq ft, or 15 squares. For shingle bundles use the roofing shingles calculator, which uses the same area.
- What is considered a steep roof?
- There is no single code line, but roofers commonly call anything over 7:12 steep and anything over 12:12 very steep. Walking and working on it needs harnesses and roof brackets, and shingle makers ask for extra fastening on steep slopes. That is an estimate of trade usage, not a code limit.
Handy tools
- Slope Calculator: Work a slope from any two of rise, run, angle, percent grade or length, for a ramp or a drain as well as a roof.
- Triangle Calculator: Solve the whole roof triangle from any three known parts, such as the rafter length from the run and rise.
- Feet and Inches Calculator: Add building sides measured in feet, inches and fractions, and get decimal feet for the length and width.