Skip to main content
ponderloop

Deck Screw Calculator: How Many Screws or Hidden Fasteners?

A 20 × 12 ft deck (240 sq ft) of 5.5 in boards with 3/16 in gaps, joists 16 in on center, needs 3 boxes of 5 lb #10 × 2-1/2 in face screws: 416 places where a board crosses a joist (26 rows × 16 joists), 2 screws each, is 832 screws, 916 with 10% extra, about 13 lb. Hidden clips take 1 per crossing: 458 clips with 10% extra, 6 boxes of 90. The board count is the deck boards calculator’s, so the two always agree.

Figures based on the sources listed belowUpdated How we calculate

Extra fasteners
Face screws: 2 per board per joist. Hidden clips: 1 clip per board per joist. Edge-screw systems drive 2 screws into the board edges at each joist. Follow your decking’s installation guide.
The IRC asks for at least two fasteners per board at each joist. Some lumber guides add a third for boards wider than 6 in to hold them flat; that is trade advice, not code, so check your decking’s guide.
Counts per pound vary by brand, head and coating by 10% or more; the box label has the real count. 2-1/2 in suits 5/4 and 2× boards; composite makers name their own screw.
Deck screws are sold by weight: 1, 5 and 25 lb are the usual boxes and buckets.
The same geometry as the deck boards calculator. A diagonal lay is an estimate; it commonly needs joists 12 in on center.
Actual width, not nominal. Narrower boards mean more rows and more fasteners.

Follow the decking maker’s gap spec. 3/16 in (0.1875) is a common default.
Check your decking’s spec: 24 in is only for decking rated for it, and 12 in is commonly needed for diagonal lay. It sets the number of joists and so of fasteners.

Buy 3 boxes.

Buy 3 boxes

240 sq ft + 10% waste = 264 sq ft

  • Fastening points (a board over a joist): 416 points, 2 screws each
  • Joists (16 in on center): 16 joists
  • Face screws, with extra: 916 screws
  • Screw weight (#10 × 2-1/2 in, estimate): 13 lb, about 73 per lb
  • Joist hanger fasteners: use the hanger’s own nails or structural screws, not deck screws
How this number is calculated

240 sq ft + 10% waste = 264 sq ft ÷ 105.29 sq ft per box = 3 boxes

Shopping list

  • Deck screws (#10 × 2-1/2 in, exterior coated)
  • Hidden deck fastener clips
  • Hidden edge deck screws
  • Star (T25) driver bits
  • Structural connector screws for joist hangers
  • Joist hanger nails (10d × 1-1/2 in)
Show diagram

Saved projects

No saved projects yet.

Fasteners for a 20 × 12 ft deck by joist spacing

5.5 in boards, 3/16 in gaps, boards along the 20 ft side, no extra. A crossing is a board over a joist. Worked by this calculator; add the extra percentage on top.
Joist spacingJoistsCrossingsFace screws (2 each)Face screws (3 each)Hidden clips
12 in215461,0921,638546
16 in164168321,248416
24 in11286572858286

Screws per box by weight (typical)

Typical screws per pound for exterior deck screws, 2-1/2 in long; brands vary by 10% or more. An estimate: the box label has the real count.
ScrewPer lb1 lb5 lb25 lb
#10 × 2-1/2 in73733651,825
#8 × 2-1/2 in86864302,150

Makers’ box ratings for hidden fasteners

Each rating is for 16 in joists and a stated board width and includes some allowance; the last column is pieces ÷ sq ft. Camo’s figures assume 2 screws per board per joist.
FastenerPieces in the boxRated for (sq ft)Pieces per sq ft
Camo hidden edge screws3501003.5
Camo hidden edge screws7002003.5
Camo hidden edge screws1,7505003.5
Trex Hideaway hidden clips90501.8
Simpson EB-TY hidden clips1751001.75
Trex Hideaway hidden clips9005001.8

Methodology & assumptions

Fastening points come from the same geometry as the deck boards calculator: rows = deck width in inches ÷ (board width + gap), rounded up, and joists = ceil(run in inches ÷ joist spacing) + 1, with a point wherever a board crosses a joist (rows × joists; cutouts reduce it in proportion to the area they take). A diagonal lay counts the board length laid × cos 45° ÷ the spacing. Board length does not change the number of crossings, so it is not asked. Face screws go 2 to a point, the minimum the IRC asks for, or 3 when you pick that for wide boards; hidden clips go 1 to a point, with a screw in the box; hidden edge screws (Camo-style) go 2 to a point. The extra percentage is added and the total rounded up once, and boxes are the fasteners ÷ the pieces in a box, rounded up. A box of screws sold by weight holds weight × typical screws per pound: about 73 per lb for #10 × 2-1/2 in and 86 for #8 × 2-1/2 in. These are typical figures read from retail listings, and brands, heads and coatings vary by 10% or more, so the box label wins. Makers rate their boxes in square feet (for example 350 Camo screws for 100 sq ft, or 90 Trex Hideaway clips for 50 sq ft) at 16 in joists and a stated board width, with some allowance in the rating. For clip and edge-screw systems the result also shows the boxes that rating gives, and the larger of the two is the safer buy. Joist hangers are not counted: the hanger’s own nails or structural screws are named in its installation sheet (commonly 10d × 1-1/2 in hanger nails or the maker’s #9 × 1-1/2 in structural screws), and deck screws are not a substitute. Everything is for new boards laid on level joists. Butt joints, stripped heads and the screws you drop are what the extra percentage pays for.

How to calculate deck screws and hidden fasteners

  1. Measure the deck and pick the board width. Enter the length and width and take off any cutouts. The board width and gap set how many rows there are.
  2. Count the joists. Joists = the run in inches ÷ the spacing, rounded up, plus one. 16 in on center is common; 12 in for diagonal lay and some composites.
  3. Count the crossings. Every row of boards crosses every joist once, so crossings = rows × joists.
  4. Multiply by the fasteners per crossing. Face screws: 2 per crossing (3 if the decking maker asks for it on wide boards). Hidden clips: 1. Hidden edge screws: 2. Add 5 to 10% extra.
  5. Convert to boxes. Divide by the pieces in a box: weight × screws per pound for screws sold by weight, or the count printed on a clip or edge-screw box. Round up.

Worked examples

ProjectResult
20 × 12 ft deck, 5.5 in boards, 3/16 in gaps, joists 16 in, 2 face screws per crossing, 5 lb boxes of #10 × 2-1/2 in240 sq ft + 10% → 3 boxes, 916 screws, 16 joists
The same deck with a third screw per crossing for wide boards (estimate)240 sq ft + 10% → 4 boxes, 1,373 screws
The same deck with hidden clips, boxes of 90240 sq ft + 10% → 6 boxes, 458 clips
The same deck with hidden edge screws, boxes of 350 (Camo-style)240 sq ft + 10% → 3 boxes, 916 screws
12 × 10 ft deck of 2 × 4 boards (3.5 in), 3/16 in gaps, joists 16 in, face screws, 5 lb boxes120 sq ft + 10% → 2 boxes, 726 screws, 10 joists
14 × 10 ft deck laid diagonally (estimate), joists 12 in, face screws, 5 lb boxes140 sq ft + 10% → 2 boxes, 460 screws, 15 joists

Frequently asked questions

How many deck screws do I need?
Count the places each board crosses a joist and multiply by the screws in each. A 20 × 12 ft deck of 5.5 in boards has 26 rows crossing 16 joists at 16 in on center, 416 crossings, so 832 screws at 2 each, 916 with 10% extra. As a rule of thumb that is about 3.5 screws per sq ft of decking, but the count moves with the board width and the joist spacing, so work it from the geometry.
How many screws are in a pound of deck screws?
For #10 × 2-1/2 in exterior deck screws, retail listings show about 73 to 82 per pound (a 5 lb box is roughly 365 to 410), and about 86 for #8 × 2-1/2 in. This calculator uses 73 and 86. It is an estimate: head style, coating and brand shift it by 10% or more, so read the count on the box. The 916 screws of the example weigh about 12.5 lb.
Do I need 2 or 3 screws per board per joist?
Two. The IRC asks for at least two fasteners where each board meets a joist. Some lumber guides add a third for boards wider than 6 in, to keep them from cupping, and the calculator has that as an option: the same deck takes 1,248 screws instead of 832, 4 boxes instead of 3. That third screw is trade advice and not code, so follow your decking maker’s guide.
How many hidden fasteners do I need per square foot?
One clip for each place a board crosses a joist, which for 5.5 in boards at 16 in is about 1.73 clips per sq ft. Makers rate their boxes a little higher to allow for waste: 90 Trex Hideaway clips cover 50 sq ft (1.8 per sq ft), 175 Simpson EB-TY clips about 100 sq ft, and 350 Camo edge screws 100 sq ft (3.5 screws per sq ft, at 2 per crossing). The example deck needs 458 clips with 10% extra: 6 boxes of 90 or 3 of 175.
Is the maker’s coverage rating or the geometry count right?
They answer slightly different questions. The rating is a round figure for 16 in joists and a typical board width, with allowance built in; the geometry count follows your width, gap and joist spacing. The result shows both for clips and edge screws (the example: 3 boxes of 350 Camo screws by geometry, 3 by rating). Buy the larger one if they differ, and expect them to drift apart with 12 in or 24 in joists, 3.5 in boards or a diagonal lay.
How does joist spacing change the screw count?
Closer joists mean more crossings. The 20 × 12 ft example crosses 21 joists at 12 in, 16 at 16 in and 11 at 24 in, which is 1,092, 832 and 572 face screws before the extra. 24 in on center is only for decking rated for it, and diagonal lay commonly needs 12 in. See the deck joist span calculator for the joist size.
What fasteners go in joist hangers?
The ones the hanger asks for, not deck screws. Joist hanger installation sheets name the nails (commonly 10d × 1-1/2 in hanger nails) or the maker’s structural screws, such as the Simpson Strong-Drive SD #9 × 1-1/2 in, that the load tables are based on. Deck and drywall screws are not load-rated for hangers and are brittle in shear. Fill every hole the table calls for; the number depends on the hanger model, so this calculator does not count them.
What length of screw do I need for deck boards?
The screw has to go through the board and about 1-1/4 in into the joist. 2-1/2 in is the usual length for 5/4 and 2× boards (about 1 to 1-1/2 in thick), and it is the length the weights here are for. Composite and PVC makers name their own screw, often a shorter one with a special head, and hidden systems come with their own screws, so use what the installation guide for your decking says.

Related calculators