Concrete Block Fill Calculator: How Much Concrete to Fill CMU Cores?
Filling every 4th core (32 in on center, the usual rebar spacing) of a concrete block wall 24 ft long and 8 ft high (192 sq ft) in 8 in wide block takes about 0.83 cubic yards (22.3 cu ft) of fill. With 10% waste that is 0.91 cubic yards: 41 bags of 80 lb concrete mix (or 55 bags of 60 lb). Filling every core of the same wall takes 2.15 cubic yards, 107 bags of 80 lb mix with the same waste. The yield is per sq ft of wall, from published tables for two-core block: 8 in block takes 1.12 cu yd per 100 sq ft with every core filled. This is a material estimate, not structural design.
Figures based on the sources listed belowUpdated How we calculate
Buy 41 bags.
Buy 41 bags
0.83 cu yd + 10% waste = 0.91 cu yd
- Wall area: 192 sq ft
- Fill before waste: 22.3 cu ft
- Fill with waste: 24.5 cu ft
- 80 lb bags of concrete mix (0.60 cu ft each): 41 bags
- 60 lb bags of concrete mix (0.45 cu ft each): 55 bags
Low
$184.50
Expected
$246.00
High
$328.00
Includes 0.08 cu yd waste
How this number is calculated
0.83 cu yd + 10% waste = 0.91 cu yd ÷ 0.0222 cu yd per bag = 41 bags
0.9 cu yd — ~9% of a standard truck load
Bagged vs. Ready-mix delivery
Bagged (80 lb bags)
41 bags
$184.50–$328.00 (typ. $246.00)
Ready-mix delivery
0.9 cu yd
$187.14–$241.63 (typ. $209.85)
For ~0.9 cu yd, ready-mix delivery is usually cheaper and far less labor.
Shopping list
- 80 lb concrete mix bag
- Mixing tub
- Concrete vibrator for block fill
- Grout bag or funnel
- Rebar (1/2 inch)
- Wheelbarrow
Your project
- Wall length × wall height: 24 × 8 ft
- Block width: 8 in (8 × 8 × 16 nominal)
- Fill pattern: Every 4th core (cores 32 in on center)
- Blocks in the wall (0 to use length and height): 0
- Bag size: 80 lb (0.60 cu ft)
- Waste: Standard (10%)
Also pick up
- 80 lb concrete mix bag
- Mixing tub
- Concrete vibrator for block fill
- Grout bag or funnel
- Rebar (1/2 inch)
- Wheelbarrow
Reopen this calculation: /calculators/block-fill-concrete/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjoyNCwid2lkdGhGdCI6OH0sImRlZHVjdGlvbnMiOltdLCJ3YXN0ZVBjdCI6MC4xLCJwYXJhbXMiOnsid2lkdGhJbiI6OCwicGF0dGVybiI6NCwiYmxvY2tzIjowLCJiYWdMYiI6ODB9fQ
Show diagram
Saved projects
No saved projects yet.
Fill for 100 sq ft of block wall by width and pattern
| Cores filled | 6 in block | 8 in block | 10 in block | 12 in block |
|---|---|---|---|---|
| Every core | 0.93 cu yd, 25.1 cu ft, 42 bags | 1.12 cu yd, 30.2 cu ft, 51 bags | 1.3 cu yd, 35.1 cu ft, 59 bags | 1.73 cu yd, 46.7 cu ft, 78 bags |
| Every 2nd core, 16 in o.c. | 0.55 cu yd, 14.9 cu ft, 25 bags | 0.65 cu yd, 17.6 cu ft, 30 bags | 0.76 cu yd, 20.5 cu ft, 35 bags (est.) | 1.01 cu yd, 27.3 cu ft, 46 bags |
| Every 3rd core, 24 in o.c. | 0.42 cu yd, 11.3 cu ft, 19 bags | 0.5 cu yd, 13.5 cu ft, 23 bags | 0.58 cu yd, 15.7 cu ft, 27 bags (est.) | 0.76 cu yd, 20.5 cu ft, 35 bags |
| Every 4th core, 32 in o.c. | 0.35 cu yd, 9.5 cu ft, 16 bags | 0.43 cu yd, 11.6 cu ft, 20 bags | 0.49 cu yd, 13.2 cu ft, 23 bags (est.) | 0.64 cu yd, 17.3 cu ft, 29 bags |
| Every 6th core, 48 in o.c. | 0.29 cu yd, 7.8 cu ft, 14 bags (est.) | 0.35 cu yd, 9.5 cu ft, 16 bags (est.) | 0.4 cu yd, 10.8 cu ft, 19 bags (est.) | 0.54 cu yd, 14.6 cu ft, 25 bags (est.) |
Fill in one concrete block by width and pattern
| Cores filled | 6 in block | 8 in block | 10 in block | 12 in block |
|---|---|---|---|---|
| Every core | 0.223 cu ft | 0.269 cu ft | 0.312 cu ft | 0.415 cu ft |
| Every 2nd core, 16 in o.c. | 0.132 cu ft | 0.156 cu ft | 0.182 cu ft (est.) | 0.242 cu ft |
| Every 3rd core, 24 in o.c. | 0.101 cu ft | 0.12 cu ft | 0.139 cu ft (est.) | 0.182 cu ft |
| Every 4th core, 32 in o.c. | 0.084 cu ft | 0.103 cu ft | 0.118 cu ft (est.) | 0.154 cu ft |
| Every 6th core, 48 in o.c. | 0.07 cu ft (est.) | 0.084 cu ft (est.) | 0.096 cu ft (est.) | 0.13 cu ft (est.) |
Methodology & assumptions
Wall area = length × height in sq ft, or, if you enter a block count, blocks ÷ 1.125 (a full-size block takes a 16 × 8 in module with its 3/8 in joints, 128 sq in, so 1.125 blocks cover a sq ft). Fill = wall area × the published yield per sq ft for the block width and fill pattern, in cubic yards; cu ft is that × 27. The yield tables give cu yd of grout or concrete per 100 sq ft of wall for two-core block: with every core filled, 0.93, 1.12, 1.3 and 1.73 cu yd for 6, 8, 10 and 12 in block. For 8 in block that is 0.27 cu ft per block, in line with a supplier's rule that 1 cu yd fills about 100 8 in blocks. When only some cores are filled, the published rows (6, 8 and 12 in at 16, 24 and 32 in on center) are used as they are; they are more than the cores alone (every 4th core of a 16 in block with two cores is a quarter of the cores, but the table is about 38% of the full yield), which the supplier tables do not explain; allowing for fill that spreads past the bare cores (joint gaps, bond-beam and end cores) is the usual reason, so treat it as an estimate. Two sets of figures are NOT in any table found and are estimates: the 10 in block at 16, 24 and 32 in on center (the 10 in full yield times the average ratio of the 8 and 12 in rows), and every column at 48 in on center (about 31% of the full yield, continuing the trend of the published rows). A geometric rule that scales full fill by core spacing alone would give less at 48 in (a sixth of full), so the 48 in figures lean to the high side. A waste allowance (10% standard, 5% tight, 15% generous) is added for spillage, blown-out cores, mortar droppings that block cores and the volume left in the mixer, wheelbarrow and hose; the result is divided by the bag yield (80 lb about 0.60 cu ft, 60 lb about 0.45 cu ft per the Quikrete data sheet) and rounded up once. Bag counts for both sizes are shown; the size you pick sets the headline and the cost. Bagged concrete mix is not the same product as bagged grout or core-fill mix: check the yield on the bag, and for more than about a cubic yard order ready-mix grout or core fill by the truck. This estimates the fill only: not the blocks, mortar, rebar, bond beams or lintels, and which cores are filled and with what mix is set by the engineer or the local code. The metric toggle shows the wall in m and the volume in m³.
- Inch Calculator, "Concrete Block Fill Calculator": table of cu yd of concrete or grout per 100 blocks and per 100 sq ft of wall for 6, 8, 10 and 12 in block, all cores filled (0.93, 1.12, 1.30 and 1.73 cu yd per 100 sq ft)
- Fairbanks Materials, "Grout Calculations for Concrete Blocks": cu yd of grout per 100 sq ft of wall for two-core block, all cells filled and at 16, 24 and 32 in on center (the source of the 6, 8 and 12 in partial-fill rows)
- Westbrook Concrete Block Co., "Fine Core Fill Grout Yields": 1 cu yd of grout fills 100 8 in blocks, fully grouted
- NCMA (CMHA) TEK 4-2A, Estimating Concrete Masonry Materials: tabulates grout per 100 sq ft of wall by wall thickness and grout spacing. Secondhand citations of it put an 8 in wall at about 1.34 cu yd per 100 sq ft with every cell filled, about 20% above the supplier tables used here, so a figure from the TEK or from your supplier may differ
- Quikrete Concrete Mix (No. 1101) data sheet: 80 lb ≈ 0.60 cu ft, 60 lb ≈ 0.45 cu ft per bag
- ASTM C476, Standard Specification for Grout for Masonry, and the local building code: the mix and the cores to fill are set by the engineer or the code
- The 10 in block at 16, 24 and 32 in on center, and every block width at 48 in on center, are estimates scaled from the published rows (see the methodology), not figures from a table
How to calculate how much concrete to fill concrete block cores
- Measure the wall. Measure the length and height of the wall in feet, or count the blocks if you know the number.
- Pick the block width. Use the nominal width of the block: 6, 8, 10 or 12 in. The face of a standard block is 8 × 16 in.
- Choose the fill pattern. Pick every core, or the spacing of the filled cores (16, 24, 32 or 48 in on center), as the engineer or the local code specifies.
- Multiply by the yield. Multiply the wall area by the published yield per sq ft for that width and pattern. 8 in block with every core filled takes about 1.12 cu yd per 100 sq ft.
- Add waste. Add 10% for spillage and extra, or 5% to 15% depending on the job.
- Convert to bags or order by the yard. Divide cubic yards by 0.0222 for 80 lb bags or 0.0167 for 60 lb bags and round up, or order ready-mix grout by the cubic yard when the job is more than about a yard.
Worked examples
| Project | Result |
|---|---|
| 24 ft long, 8 ft high wall, 8 in block, every 4th core (32 in on center), standard waste | 0.83 cu yd (192 sq ft wall) + 10% ≈ 0.91 cu yd → 41 bags of 80 lb mix |
| 24 ft long, 8 ft high wall, 8 in block, every core filled, standard waste | 2.15 cu yd (192 sq ft wall) + 10% ≈ 2.37 cu yd → 107 bags of 80 lb mix |
| 30 ft long, 6 ft high wall, 12 in block, every 3rd core (24 in on center), 15% waste, 60 lb bags | 1.37 cu yd (180 sq ft wall) + 15% ≈ 1.57 cu yd → 95 bags of 60 lb mix |
| 150 blocks of 8 in block, every 2nd core (16 in on center), tight 5% waste | 0.87 cu yd (133.3 sq ft wall) + 5% ≈ 0.91 cu yd → 41 bags of 80 lb mix |
| 20 ft long, 4 ft high wall, 6 in block, every 6th core (48 in on center, estimate), standard waste | 0.23 cu yd (80 sq ft wall) + 10% ≈ 0.26 cu yd → 12 bags of 80 lb mix |
| 10 ft long, 10 ft high wall, 10 in block, every core filled, standard waste | 1.3 cu yd (100 sq ft wall) + 10% ≈ 1.43 cu yd → 65 bags of 80 lb mix |
Frequently asked questions
- How much concrete does it take to fill cinder blocks?
- For solid fill of an 8 in block wall, about 1.12 cu yd per 100 sq ft of wall, or about 0.27 cu ft per block (one cu yd for about 100 blocks). 6 in block takes 0.93, 10 in 1.3 and 12 in 1.73 cu yd per 100 sq ft. If only the cores with rebar are filled, it is much less: 0.43 cu yd per 100 sq ft for 8 in block with cores 32 in on center. Multiply by the wall area and add 10% for waste.
- How many bags of concrete to fill a block wall?
- Divide the cubic yards with waste by the yield of the bag, 0.0222 cu yd for an 80 lb bag and 0.0167 for 60 lb, and round up. The 192 sq ft example wall filled every 4th core is 41 bags of 80 lb mix, or 55 bags of 60 lb; filled solid it is 107 bags of 80 lb. A solid 8 in wall takes about 51 bags of 80 lb mix per 100 sq ft before waste. Check the yield on the bag you buy.
- How do I calculate the fill if I only know the number of blocks?
- Enter the block count and the calculator turns it into wall area at 1.125 blocks per sq ft, which is 0.889 sq ft of wall per block. For example 150 blocks of 8 in block with every 2nd core (16 in on center) filled is 133.3 sq ft and 0.87 cu yd, 0.91 with 5% waste, 41 bags of 80 lb mix. The count must be full-size 8 × 16 in face blocks, not half blocks or half-height units.
- How much concrete is in one concrete block?
- A solid-filled 8 in block holds about 0.27 cu ft of fill, a 6 in block 0.22, a 10 in block 0.31 and a 12 in block 0.42 cu ft (the table yields spread over the blocks in a wall, so they include a little spillage). That is the volume of the two cores plus the filled gaps at the joints; a real 8 in block's cores alone are somewhat less. Wall-wide yields are the better guide than the block size.
- Which cores should be filled, and what spacing is typical?
- That is a structural question. Rebar is usually placed at 16, 24, 32 or 48 in on center, and the core around each bar is filled, plus bond beams and the cores at corners, openings and ends. The engineer or the local code specifies the pattern, bar size and mix; a short freestanding garden wall, a retaining wall and a foundation wall are very different. This calculator only works out the material for the pattern you pick. The cores at openings, lintels, bond beams and the bottom course are not added.
- Is it concrete, grout or core fill, and can I use bagged concrete?
- Masonry fill is made to ASTM C476 as fine or coarse grout, which is a fluid mix with a high slump so that it flows into the cores. Bagged concrete mix is usually stiffer and has larger stone, so it can bridge in narrow cores; 3/8 in pea-gravel core-fill mix is also sold. For a few cores a wet mix of bagged concrete is often used; for a whole wall order ready-mix grout or core fill and ask what the code requires. The volume per sq ft is about the same for any of them.
- How much waste should I allow?
- 10% is a typical allowance for spillage, cores that take more than the table (cracked or broken web, large bond-beam units) and mix left in the mixer and hose. Use 5% for a short wall with the cores swept clean and a mix you can measure, and 15% for a tall wall, a pump or a mortar-fouled core. For the example wall, 5% waste is 0.87 cu yd and 15% is 0.95 cu yd, against 0.91 cu yd at 10%.
- Do the figures include 48 in on center?
- The 48 in on center column and the 10 in block's partial-fill rows are estimates, scaled from published rows, because no table found lists them. For 8 in block at 48 in on center the calculator uses 0.35 cu yd per 100 sq ft; a purely geometric rule (a sixth of the solid-fill yield) would give about 0.19. The page marks these figures as (est.). Check your supplier's own yield for a large order.
- How do I measure the wall and handle openings?
- Multiply the length by the height of the wall in feet, and for a wall with doors or windows work the wall in sections or measure only the filled length, since the cores beside an opening are usually filled solid anyway. This calculator does not subtract openings: enter the area that is filled. For a wall with different block widths or patterns, run each section separately and add the results.
Handy tools
- Feet and Inches Calculator: Turn a tape reading in feet, inches and fractions into the decimal feet the wall length and height fields take.