Asphalt Driveway Sealer Calculator
Pails of sealer = area × (1 + waste) × coats ÷ the area one pail covers in one coat, rounded up. A 40 × 12 ft driveway is 480 sq ft, or 528 sq ft with 10% waste. A 4.75-gallon pail of asphalt emulsion covers about 400 sq ft on new or smooth pavement (the low end of Latex-ite’s published 400 to 500, a typical figure, read here as one coat), so two thin coats need 3 pails. Old, rough or unsealed asphalt covers about 300 sq ft per pail, which makes it 4 pails for two coats, and a single coat on smooth pavement would be 2 pails. Fill cracks first: 40 ft of cracks is 2 tubes. Coverage is typical, not a guarantee, so check your pail’s label.
Figures based on the sources listed belowUpdated How we calculate
Buy 3 pails.
Buy 3 pails
480 sq ft + 10% waste = 528 sq ft
- Surface to seal: 480 sq ft
- Coats: 2 coats: one 4.75-gallon pail covers about 200 sq ft at this many coats
- Sealer needed (exact): 12.5 gal
- Crack filler: 2 × 10.1 oz tube for 40 ft of cracks (about 32 ft each)
- Drying: Latex-ite Optimum data sheet: second coat after 24 hours, cure 24 to 48 hours at 70°F and 50% humidity, apply at 55°F and rising
- Application: Work the sealer in with a driveway squeegee, then smooth it with a sealing brush or push broom; keep each coat thin and cut in the edges by brush
How this number is calculated
480 sq ft + 10% waste = 528 sq ft ÷ 200 sq ft per pail = 3 pails
Shopping list
- Driveway sealer (5 gal)
- Driveway crack filler
- Driveway squeegee
- Sealcoating brush
- Asphalt cleaner and degreaser
Your project
- Length × width: 40 × 12 ft
- Sealer type: Coal-tar-free asphalt emulsion (standard)
- Driveway surface: New, smooth or previously sealed
- Pail size: 4.75-gallon pail
- Coats: 2
- Cracks to fill: 40 ft
- Crack filler pack: 10.1 oz tube (about 32 ft of 1/4 in bead)
- Waste: Standard (+10%)
Also pick up
- Driveway sealer (5 gal)
- Driveway crack filler
- Driveway squeegee
- Sealcoating brush
- Asphalt cleaner and degreaser
Reopen this calculation: /calculators/asphalt-sealer/?s=eyJyb29tIjp7Imxlbmd0aEZ0Ijo0MCwid2lkdGhGdCI6MTJ9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMSwicGFyYW1zIjp7InByb2R1Y3QiOjEsImNvbmRpdGlvbiI6MSwicGFpbCI6MSwiY29hdHMiOjIsImNyYWNrRnQiOjQwLCJmaWxsZXIiOjF9fQ
Show diagram
Saved projects
No saved projects yet.
Typical coverage per pail by sealer type and surface
| Sealer type | New, smooth or sealed (sq ft/pail) | Old, rough or unsealed (sq ft/pail) |
|---|---|---|
| Asphalt emulsion | 400 | 300 |
| Acrylic | 1118 | 838 |
| Fast dry | 400 | 300 |
How many pails for common driveways
| Driveway | Area with waste (sq ft) | Emulsion, smooth (pails) | Emulsion, old or porous (pails) | Acrylic, smooth (pails) |
|---|---|---|---|---|
| 10 × 20 ft single-car pad | 220 | 2 | 2 | 1 |
| 10 × 40 ft single driveway | 440 | 3 | 3 | 1 |
| 12 × 40 ft driveway | 528 | 3 | 4 | 1 |
| 20 × 24 ft double driveway | 528 | 3 | 4 | 1 |
| 20 × 50 ft wide, long driveway | 1,100 | 6 | 8 | 2 |
Crack filler coverage
| Pack | Typical coverage | Source |
|---|---|---|
| 10.1 oz tube | about 32 ft of 1/4 in bead | Latex-ite 42376 listing |
| 1-gallon jug | about 160 ft of 1/4 × 1/4 in crack | Sakrete listing |
Methodology & assumptions
Surface area is length times width, less any area you will not seal. It is multiplied by 1 plus the waste allowance (0%, 10% or 20%), by the number of coats, and divided by the area a pail covers in one coat, then rounded up to whole pails. Makers quote one coverage figure per pail by surface condition; except for the acrylic sheet, which says two coats, the calculator reads it as one coat (the safe reading): 400 sq ft per 4.75-gallon pail on new or smooth asphalt and 300 on old or rough asphalt for the emulsion and fast-dry types (the low end of Latex-ite’s published 400 to 500 and 300 to 400), and about 1,118 and 838 sq ft per coat per 4.75 gallons for the acrylic (an older Latex-ite sheet quoting two coats for a 3.4-gallon pail, scaled by volume). A 5-gallon pail covers 5/4.75 as much. Other brands list lower: Jetcoat 250 to 350 per 4.75-gallon pail, Henry 200 to 400 per 5-gallon pail. The “fast dry” type uses the same coverage as the standard emulsion. All of these are typical figures and estimates, not guarantees, and the waste percentages are rules of thumb. Crack filler is the total crack length divided by the length one pack fills (about 32 ft for a 10.1 oz tube at a 1/4 inch bead, about 160 ft for a gallon at 1/4 by 1/4 inch), rounded up; wider or deeper cracks need more. Drying times are shown only where a data sheet or listing gives them. The metric toggle shows lengths in m and areas in m²; sealer is still sold in US pails.
- Latex-ite, Optimum Pro Blacktop Driveway Resurfacer product data sheet (4.75 gal pail): 400-500 sq ft smooth or previously sealed, 300-400 rough or unsealed; two thin coats, second coat after 24 hours, cure 24-48 hours at 70°F and 50% RH, apply at 55°F and rising
- Latex-ite, Ultra Shield 4.75 Gal. Blacktop Driveway Sealer (coal tar free, fast dry) retailer listing: 400-500 and 300-400 sq ft, about 1 hour to touch, 24 hour cure
- Latex-ite, Acrylic Grade Driveway Sealer product data sheet (3.4 gal pail, 2018): about 400 sq ft per pail for two coats on good surfaces, 300 moderate, 200 poor; cure 24-48 hours
- JetCoat, 4.75 Gal. 5 Year Premium Driveway Sealer & Filler retailer listing: 250-350 sq ft per pail
- Henry, Driveway Filler and Sealer product listings: 200-400 sq ft per 5-gallon pail depending on surface texture
- Latex-ite, Asphalt Driveway Crack and Joint Filler 10.1 oz (42376) Home Depot listing: fills up to 32 ft with a 1/4 in bead
- Gardner-Gibson, Black Jack CAS-73 Commercial Asphalt Sealer product listing: about 380 sq ft per 5-gallon pail
- Sakrete, 1 gallon Blacktop Crack Filler product listing: coverage 1/4 in × 1/4 in × 160 ft
- Minnesota Pollution Control Agency, coal tar sealer ban and local ban table (tdr-g1-12): Minnesota statewide ban effective January 1, 2014
- Ecology Center, Coal Tar Sealants: Washington (first statewide ban, sales after 2012), Minnesota and local bans
- States Newsroom, “Bill banning certain driveway pavement sealants to take effect July 1” (Virginia, 2024)
How to calculate how much asphalt driveway sealer you need
- Measure the driveway. Measure the length and width in feet and multiply them. Subtract any area you will not seal, such as a flower bed or a patch of concrete.
- Pick the sealer type and surface. Choose asphalt emulsion, acrylic or fast dry, then new or smooth versus old or porous pavement. Compare the coverage on your pail with the table.
- Set coats and pail size. Two thin coats are typical. Pails are 4.75 gallons for most brands and 5 gallons for some.
- Add waste. Add 10% for edges and the sealer left in the pail, or 20% for very rough pavement.
- Divide and round up. Divide the area with waste by the coverage per pail at your coats and round up to whole pails.
- Add crack filler. Divide the total crack length by what one tube or jug covers and round up.
Worked examples
| Project | Result |
|---|---|
| 40 × 12 ft driveway, asphalt emulsion, new or smooth, 2 coats, 40 ft of cracks | 480 sq ft + 10% waste ≈ 528 sq ft → 3 pails and 2 tubes of crack filler |
| 40 × 12 ft driveway, old and porous, 2 coats | 528 sq ft with waste → 4 pails |
| 20 × 24 ft double driveway, fast dry, old and porous, 2 coats, 100 ft of cracks in 1-gallon jugs | 480 sq ft + 10% waste ≈ 528 sq ft → 4 pails and 1 jug |
| 20 × 50 ft long driveway, acrylic, new or smooth, 5-gallon pails, 20% waste | 1,000 sq ft + 20% waste ≈ 1,200 sq ft → 3 pails |
Frequently asked questions
- How much sealer do I need for a driveway?
- A 40 × 12 ft driveway is 480 sq ft, or 528 sq ft with 10% waste. Latex-ite lists about 400 to 500 sq ft per 4.75-gallon pail for smooth or previously sealed asphalt and 300 to 400 for rough or unsealed. Read as one coat, at the low end, 400 sq ft per pail, two thin coats take 3 pails; on old, porous asphalt at 300 it is 4. Change the type, surface, coats and pail size in the calculator to see yours.
- How many square feet does a pail of driveway sealer cover?
- Typically 250 to 500 sq ft per 4.75-gallon pail depending on the brand and the pavement. Latex-ite lists 400 to 500 on smooth or sealed asphalt and 300 to 400 on rough or unsealed; Jetcoat lists 250 to 350; Henry lists 200 to 400 per 5-gallon pail; a Gardner-Gibson commercial sealer lists about 380 per 5 gallons. Pavement with large aggregate covers less, and hand application usually covers less than spraying. The calculator uses the low end of Latex-ite’s ranges.
- Are the coverage figures per coat or for two coats?
- Makers mostly give one figure per pail and recommend two thin coats; Latex-ite’s acrylic sheet says outright that its figure is for two coats, and its Optimum sheet recommends two thin coats because thick coats track and cure unevenly. The Optimum and emulsion listings do not say the figure covers two coats, so the calculator reads it as one coat, the safe reading that makes sure you buy enough: two coats take twice the pails of one. For the acrylic, whose sheet does say two coats, the figure is halved to a per-coat rate. If your label says its figure covers two coats, enter 1 coat.
- How much crack filler do I need?
- Add up the length of the cracks and divide by what one pack covers. A Latex-ite 10.1 oz tube lists about 32 feet with a 1/4 inch bead and a Sakrete 1-gallon jug lists about 160 feet of 1/4 by 1/4 inch crack. Wider or deeper cracks use more, so round up, and fill cracks before sealing. Latex-ite’s 2X blacktop crack filler is sold for cracks up to 1/2 inch wide; for wider ones follow the product label.
- What is the best way to apply driveway sealer?
- Clean and dry the pavement, fill the cracks, and apply in a temperature range on the label (Latex-ite’s Optimum sheet says 55°F and rising). Pour a ribbon of sealer, spread it with a driveway squeegee, then smooth it with a sealing brush or push broom into a thin, even film, and brush the edges. Two thin coats beat one thick one. Keep traffic off for the time on the label.
- How long does driveway sealer take to dry?
- It depends on the product and the weather, so use your label. Latex-ite’s Optimum sheet lists a second coat after 24 hours and a cure of 24 to 48 hours at 70°F and 50% humidity. Retailer listings for its fast-dry Ultra Shield say about 1 hour to touch and foot traffic with a 24 hour cure, and warn that it may not cure in cold, damp late-fall or early-spring weather. The calculator shows the sourced time for the sealer type you pick.
- Is coal tar sealer banned?
- In some places. Washington and Minnesota have statewide bans on coal-tar-based pavement sealants, and Virginia passed a limit on products with certain PAH concentrations; Washington, DC and some cities and counties (for example Austin, Texas and Dane County, Wisconsin) have local bans. This list is not complete and changes, so check your state and town. The sealers in this calculator are coal-tar-free asphalt emulsion or acrylic, which are sold everywhere.