Centimeters to Inches Explained: Dividing by 2.54
One inch is exactly 2.54 cm, so divide centimeters by 2.54 to get inches. Conversion tables, feet-and-inches results, and worked examples.
To convert centimeters to inches, divide by 2.54: 30 cm ÷ 2.54 = 11.81 in. To convert inches to centimeters, multiply by 2.54: 12 in × 2.54 = 30.48 cm. The number 2.54 is not a rounded approximation. The international inch is defined as exactly 2.54 centimeters (NIST SP 811 lists it as an exact conversion factor), so the arithmetic is as precise as your calculator allows.
Why 2.54 is exact
The international inch (1959) is exactly 25.4 millimeters, which is 2.54 centimeters. Every other common inch-based length unit follows from that:
| Unit | In inches | In centimeters |
|---|---|---|
| 1 inch | 1 | 2.54 |
| 1 foot | 12 | 30.48 |
| 1 yard | 36 | 91.44 |
Because these are all exact, you can convert between feet and metres with no loss: 1 foot is exactly 0.3048 m, and 1 yard is exactly 0.9144 m. The metre itself is defined in the SI Brochure through the speed of light, and the centimeter is one hundredth of it.
The two formulas
| Direction | Formula | Example |
|---|---|---|
| Centimeters to inches | in = cm ÷ 2.54 | 25 cm ÷ 2.54 = 9.84 in |
| Inches to centimeters | cm = in × 2.54 | 10 in × 2.54 = 25.4 cm |
Dividing by 2.54 is the same as multiplying by 0.3937 (the reciprocal, 1 ÷ 2.54 = 0.393700787…). Use whichever your calculator makes easier, but keep the extra digits and round only at the end.
Centimeters to inches table
| Centimeters | Inches (decimal) |
|---|---|
| 1 | 0.394 |
| 5 | 1.969 |
| 10 | 3.937 |
| 15 | 5.906 |
| 20 | 7.874 |
| 25 | 9.843 |
| 30 | 11.811 |
| 50 | 19.685 |
| 100 | 39.370 |
Inches to centimeters table
These are exact, so nothing is rounded:
| Inches | Centimeters |
|---|---|
| 1/4 | 0.635 |
| 1/2 | 1.27 |
| 1 | 2.54 |
| 4 | 10.16 |
| 6 | 15.24 |
| 12 | 30.48 |
| 36 | 91.44 |
| 72 | 182.88 |
Some everyday paper sizes make good reference points. A US Letter sheet, 8.5 × 11 in, is 21.59 × 27.94 cm.
Getting feet and inches, not just decimal inches
Tape measures and building plans in the US use feet, inches, and fractions of an inch, not decimals. The conversion has two extra steps: divide the total inches by 12 to get feet, then convert the leftover decimal into inches.
Example: 180 cm.
- 180 ÷ 2.54 = 70.866 inches.
- 70.866 ÷ 12 = 5.905 feet, so the whole feet are 5.
- The remaining inches are 70.866 − (5 × 12) = 10.866.
- As a fraction, 0.866 is about 14/16, or 7/8.
So 180 cm is 5 ft 10.87 in, or about 5 ft 10 7/8 in.
Example: 175 cm. 175 ÷ 2.54 = 68.898 in. That is 5 ft 8.898 in, or about 5 ft 8 7/8 in, since 0.898 is closest to 14/16.
Example: 100 cm (one metre). 100 ÷ 2.54 = 39.370 in, which is 3 ft 3.37 in, or about 3 ft 3 3/8 in.
| Centimeters | Feet and inches |
|---|---|
| 30 | 0 ft 11.81 in |
| 50 | 1 ft 7.69 in |
| 100 | 3 ft 3.37 in |
| 150 | 4 ft 11.06 in |
| 180 | 5 ft 10.87 in |
| 200 | 6 ft 6.74 in |
Converting to fractions of an inch
Most tape measures mark sixteenths. To turn a decimal inch into the nearest sixteenth, multiply the decimal part by 16 and round. For 7.874 in (20 cm): 0.874 × 16 = 13.98, which rounds to 14, so the reading is 7 14/16, which reduces to 7 7/8 in. For the nearest eighth, multiply by 8 instead.
Rounding to a sixteenth means you can be off by up to 1/32 in, about 0.8 mm. For woodworking or fitting furniture that is usually fine. If a part has to fit tightly, keep the decimal value and work in millimeters.
Millimeters, too
Since 1 cm is 10 mm, one inch is 25.4 mm. A millimeter is 1 ÷ 25.4 = 0.0394 in, and 1/16 in is 1.5875 mm.
Common mistakes
- Multiplying instead of dividing. Inches are the bigger unit, so a centimeter value always gives a smaller number of inches. If 30 cm came out as 76 in, you multiplied.
- Using 2.5 as a shortcut. 30 cm ÷ 2.5 gives 12 in, but the right answer is 11.81 in. Use 2.54.
- Reading decimal inches as inches and fractions. 5.5 in means five and a half inches, but 5.12 in is not five and a twelfth. Convert the decimal to sixteenths first.
- Rounding before converting to feet. Keep the full decimal until the last step.
Try it
For a quick answer, open the Unit Converter, choose the length category, and pick centimeters and inches. It uses the exact 2.54 factor. If you work in feet, inches and fractions, or want to add and subtract measurements such as 5’ 10” + 3’ 6”, use the Feet and Inches Calculator, which rounds to the nearest 1/16 inch and shows the same length in millimeters and centimeters.
Updated 2026-11-02