Skip to main content
ponderloop

Wood Pellet Calculator: Bags and Tons for a Pellet Stove

A pellet stove at the Englander 25-PDVC's published burn rates (1.84 lb/h on low, 4.05 lb/h on high and an estimated 2.95 on medium), run 4 hours on low, 8 on medium and 4 on high, burns 47.2 lb of pellets a day, which is 1.2 bags per day of 40 lb. Over a 150-day season that is 3.54 tons or 177 bags, and 35.4 bags in 30 days. Pellets hold about 8,200 BTU per pound (a typical figure; 8,000 to 8,500 is the usual range), so at 75% stove efficiency the season delivers 43.5 million BTU of heat, the heat of about 529 gal of propane or 3.3 cords of seasoned hardwood. Enter your stove's burn rates, or a heating load in BTU per hour, and your price per bag.

Figures based on the sources listed belowUpdated How we calculate

The burn rate is in the stove’s spec sheet or manual; the heating load is what the room or house needs (see the room heat loss and furnace size calculators).

Pounds of pellets per hour on the lowest setting, from the spec sheet. The 1.84 lb/h shown is the Englander 25-PDVC; replace it with your stove’s figure.

Hours of the day the stove runs on its lowest setting. The three settings together cannot pass 24 hours; a longer total is scaled down to 24.

Spec sheets rarely give a medium; a midpoint of the low and high is a reasonable estimate (2.95 lb/h here).

Hours of the day on the middle setting. A thermostat-run stove spends its day between low and high; use the split you see.

Pounds of pellets per hour on the highest setting, the stove’s maximum feed rate (4.05 lb/h for the Englander 25-PDVC).

Hours of the day on the highest setting, such as a cold morning warm-up.

Typically 8,000 to 8,500 BTU per pound; 8,200 is a typical figure. The bag or supplier may state it. It sets the heat from a pound in both methods, and the pounds in the heating load method.

EPA says certified pellet stoves are usually 70% to 83% efficient. Check the stove’s listing; 75% is a typical estimate.

Days you heat with the stove. 150 (five months) is a planning figure; it depends on your climate.

Use the price you pay. Prices vary by region, season and whether you buy by the bag or the ton, so this tool does not assume one.

Only for the propane comparison: the share of the propane’s heat a furnace or heater delivers. 80% to 95% is typical.

Optional: enter your price per gallon to compare the season’s cost with propane.

Only for the firewood comparison: the share of firewood’s heat a wood stove delivers. About 60% to 75% for a modern stove is a typical estimate.

Optional: the price of a full 128 cu ft cord, delivered and stacked. A “face cord” is smaller; see the firewood cord calculator.

1.2 bags per day.

1.2 bags per day

  • Pellets per day: 1.2 bags (47.2 lb) over 16 h, an average of 2.95 lb/h
  • Pellets per 30 days: 35.4 bags (1,415 lb, 0.71 tons)
  • Pellets per season: 3.54 tons (7,074 lb) over 150 days
  • Bags to buy for the season: 177 bags of 40 lb (176.8 bags, rounded up)
  • Average heat output: 18,127 BTU/h of heat from 24,170 BTU/h of pellets at 75% efficiency
  • Heat delivered per season: 43.5 million BTU (435 therms)
  • Cost per day: enter your price per bag to see this
  • Cost per 30 days: enter your price per bag to see this
  • Cost per season: enter your price per bag to see this
  • Price per ton and per million BTU of heat: enter your price per bag to see this
  • Propane that gives the same heat: 529 gal a season at 91,452 BTU per gal and 90% efficiency (enter a propane price to compare cost)
  • Firewood that gives the same heat: 3.35 cords (428 cu ft stacked) at 20 million BTU per cord and 65% efficiency (enter a cord price to compare cost)

Shopping list

  • Wood pellets (40 lb bags)
  • Pellet stove ash vacuum
  • Carbon monoxide detector
  • Pellet stove cleaning brush kit

Saved projects

No saved projects yet.

Published burn rates of common pellet stoves

Lowest and highest feed rate from the sources listed below, and the bags a day that would be at each rate if the stove ran 24 hours (worked by this calculator). A stove on a thermostat does not run flat out all day.
StoveBurn rate (lb/h)Hopper (lb)Bags a day on low, 24 hBags a day on high, 24 hSource of the rate
Englander 25-PDVC1.84 to 4.05401.12.43a spec sheet quoting the manual
Quadra-Fire Mt. Vernon E21.9 to 5.9801.143.54Quadra-Fire catalog
Quadra-Fire Mt. Vernon AE1.9 to 6.2801.143.72Quadra-Fire catalog
Harman P430.75 to 5.5500.453.3owner’s manual (2013 revision); a Harman brochure lists 4.9 lb/h max and newer retailer listings 1.9 to 4.7 lb/h

Pellets by burn rate at 16 hours a day

A steady burn rate for 16 hours a day over 150 days, 40 lb bags and short tons; heat output at 8200 BTU per lb and 75% efficiency.
Burn rateBags a dayBags per 30 daysTons per 150-day seasonBags to buy for the seasonHeat output (BTU/h)
1 lb/h0.4121.2606,150
1.5 lb/h0.6181.8909,225
2 lb/h0.8242.412012,300
2.5 lb/h130315015,375
3 lb/h1.2363.618018,450
4 lb/h1.6484.824024,600
5 lb/h260630030,750
6 lb/h2.4727.236036,900

Pellets by heating load at 16 hours a day

Pounds an hour = load ÷ (8,200 × 0.75) = load ÷ 6,150. The load is the average heat the stove must supply while it runs.
Average loadPounds an hourBags a dayBags per 30 daysTons per 150-day seasonBags to buy for the season
10,000 BTU/h1.630.6519.51.9598
15,000 BTU/h2.440.9829.32.93147
20,000 BTU/h3.251.3393.9196
25,000 BTU/h4.071.6348.84.88244
30,000 BTU/h4.881.9558.55.85293
40,000 BTU/h6.52.6787.8391
50,000 BTU/h8.133.2597.69.76488

What a ton of pellets replaces

A ton of pellets at 8,200 BTU per pound, by stove efficiency, against propane at 90% efficiency (91,452 BTU per gallon) and well-seasoned hardwood at 65% efficiency (20 million BTU per 128 cu ft cord).
Stove efficiencyHeat delivered by a ton (million BTU)Propane that gives the same heat (gal)Firewood that gives the same heat (cords)
70%11.51390.88
75%12.31490.95
80%13.11591.01
83%13.61651.05

Methodology & assumptions

This is an estimate of how many pellets a stove burns, from either its burn rate or the heat the room needs. 1) By burn rate: pounds a day = the sum, over low, medium and high, of (pounds per hour at that setting × hours a day at it). The burn rate (feed rate) is in the stove's spec sheet or manual; manufacturers usually publish the lowest and the highest, and the medium is taken as their midpoint unless you enter your own. The three settings cannot add up to more than 24 hours; a longer total is scaled down. 2) By heating load: pounds per hour = BTU per hour ÷ (BTU per pound of pellets × stove efficiency), then × hours a day. The load is an average over the hours the stove runs; the coldest-night peak from a heat loss calculation would overstate a season. 3) Bags = pounds ÷ 40, the common bag size; tons = pounds ÷ 2,000 (short tons, so a ton is 50 bags). The month is 30 days and the season is the days you enter; bags to buy for the season are rounded up to whole bags. 4) Heat from the pellets: a pound of wood pellets holds about 8,000 to 8,500 BTU depending on moisture and the wood; 8,200 is used here. Heat delivered = pounds × BTU per pound × the stove's efficiency, 75% by default; EPA says certified pellet stoves are usually between 70% and 83%. Manufacturer input ratings use the same arithmetic: a catalog states that its BTU input is the maximum feed rate × about 8,600 BTU per pound. 5) Cost = bags × your price per bag; the price per million BTU of heat divides the price of a ton by the million BTU a ton delivers at your efficiency. This tool assumes no price. 6) Comparisons: the same delivered heat in propane = heat ÷ (91,452 BTU per gallon, the EIA figure used by the propane usage calculator × the propane appliance's efficiency, 90% by default); in firewood = heat ÷ (about 20 million BTU in a 128 cu ft cord of well-seasoned hardwood × the wood stove's efficiency, 65% by default). The cord is the same 128 cu ft cord as on the firewood cord calculator. Wood species and moisture move the cord figure a lot,: oak is listed near 25 to 28 million BTU per cord, above the 20 million used here. Not covered: igniter and fan electricity, ash, a stove that cycles on and off with a thermostat (enter the average rate), pellet quality that changes the BTU per pound, and delivery fees. The figures are planning estimates; a season of your own bag count is the best measure.

How to estimate how many wood pellets a stove will burn

  1. Choose the method. Work from the stove’s burn rate in pounds per hour if you have its spec sheet, or from the heating load in BTU per hour if you know what the room needs.
  2. Enter the burn rates and hours. Enter the pounds per hour on low, medium and high and the hours a day on each setting; for the heating load, enter the average load, the pellet heat content, the stove efficiency and the hours a day.
  3. Set the season. Enter the days you heat with the stove, such as 150.
  4. Read the bags and tons. The result gives bags (40 lb) and pounds a day, per 30 days and per season, the tons, and the whole bags to buy.
  5. Add prices. Enter your price per bag for the cost, and optional propane and firewood prices to compare the same heat.

Worked examples

ProjectResult
Englander 25-PDVC rates, 4 h low, 8 h medium, 4 h high, 150 days47.2 lb a day, 1.2 bags per day, 3.54 tons a season (177 bags)
Quadra-Fire Mt. Vernon E2 (1.9 to 5.9 lb/h, taken as 3.9 lb/h) running 24 hours at $7.00 a bag93.6 lb a day, 2.3 bags per day, 7.02 tons a season, $2,457.00
A 30,000 BTU/h average load for 12 hours a day, 150 days58.5 lb a day, 1.5 bags per day, 4.39 tons a season
A small room at a 10,000 BTU/h load around the clock39 lb a day, 1 bag per day, 2.93 tons a season
A stove on its lowest setting (1.84 lb/h) for 12 hours a day22.1 lb a day, 0.6 bags per day, 1.66 tons a season
A cold-snap day: the same stove on high (4.05 lb/h) for 8 hours32.4 lb a day, 0.8 bags per day

Frequently asked questions

How many bags of pellets does a pellet stove use a day?
Pounds an hour × hours a day ÷ 40. With the default Englander 25-PDVC rates (1.84, 2.95 and 4.05 lb/h) over 4, 8 and 4 hours, the stove burns 47.2 lb, 1.2 bags per day. A stove on low all day uses about 1.1 bags and the same stove on high all day about 2.4 bags. Use far less on mild days than on cold ones.
How many tons of pellets do I need for a winter?
Pellets a day × days heated ÷ 2,000. The default load of 47.2 lb a day over 150 days is 3.54 tons, 177 bags. Round up to whole bags, add a margin for a colder winter than planned, and check how your supplier sells it (a ton is 50 bags of 40 lb).
How many bags are in a ton of pellets?
50 bags of 40 lb make a short ton of 2,000 lb. Some bags are 50 lb (40 bags to a ton), so check the weight printed on the bag.
How many BTU are in a pound of wood pellets?
About 8,000 to 8,500 BTU per pound. The US Department of Energy gives roughly 8,500 for an average pellet, a South Dakota state brochure 8,200 and a University of Wisconsin Extension presentation 8,000. This calculator uses 8,200 and lets you change it. A stove maker's BTU input rating is its maximum feed rate × about 8,600.
How do I find my stove’s burn rate?
It is in the owner’s manual or the spec sheet, listed as the feed rate, burn rate or fuel consumption in pounds per hour, usually as a lowest and a highest value. If only the BTU input is given, divide it by about 8,600, the figure Quadra-Fire uses, to get pounds an hour. The rate is the stove’s controlled feed, not what it burns when the thermostat switches it down, so a stove on a thermostat averages less than its maximum.
How do I work it out from the heating load instead?
Pounds an hour = BTU per hour ÷ (BTU per pound × stove efficiency). A 30,000 BTU/h average load at 8,200 BTU per pound and 75% is 4.88 lb/h, and over 12 hours a day 1.5 bags per day. Get the load from the room heat loss calculator, or from the furnace size calculator for a whole house; use the average, not the design-day peak.
How much does it cost to heat with pellets?
Bags × your price per bag. At an example price of $7.00 a bag (not a market price), 3.54 tons a season is 177 bags, $1,239.00. Enter your own price per bag; delivered bulk and sale prices differ. The calculator also gives the price per million BTU of heat, which is the figure to compare with propane and firewood.
Are pellets cheaper than propane or firewood?
It depends on your prices. The season's heat here is equal to about 529 gal of propane (at 91,452 BTU per gallon, the propane usage calculator's figure, and an assumed 90% efficiency) or 3.3 cords of seasoned hardwood at 65% efficiency. Enter a propane price and a cord price, and the result shows what those would cost: at example prices of $3.00 a gallon and $300.00 a cord that is $1,585.72 and $1,003.96, against $1,239.00 for pellets at $7.00 a bag. Those prices only show the arithmetic; use your own, and remember firewood takes labor and storage, while pellets need electricity.
How long does a bag of pellets last?
40 lb ÷ pounds an hour. At 1.84 lb/h a bag lasts 21.7 hours, at 2.95 lb/h 13.6 hours and at 4.05 lb/h 9.9 hours.
Is this exact?
No. Burn rates are the manufacturer’s controlled feed settings, heat content varies with the pellet, and the weather decides how long the stove runs. The medium rate and the hours on each setting are estimates. For a better number, count the bags you use over a few weeks and scale it to the season.

Related calculators