Skip to main content
ponderloop

Stair Carpet Calculator: How Much Carpet for Stairs?

13 steps with a 10 in tread, a 7.5 in riser and a 1.5 in nosing wrap, 36 in wide, and one 3 × 3 ft landing take 14 square yards of carpet on a 12 ft roll. Each step is a piece 19 in long (tread plus riser plus wrap). Four 36 in pieces stand side by side across the roll with the pile running the same way, so 13 steps take 4 rows, 6.33 ft of roll, and the landing adds 3.5 ft: 10 ft off the roll in all. Add 6 square yards of pad and about 87 ft of tack strip (two strips a step, an estimate). The nosing wrap and the piece layout are typical figures, so ask your installer to confirm before you order.

Figures based on the sources listed belowUpdated How we calculate

Extra carpet

Count each step you will cover: a staircase between two floors has one more riser than treads, and the top floor is not a step. Landings go in the landing fields.

The flat part you step on, from the face of one riser to the next. If the tread overhangs the riser, measure to the front of the overhang and put the extra in the nosing wrap.

The vertical face of each step, from tread to tread.

The width of the steps between the walls or strings, where the carpet will go.

Extra carpet to wrap over the nose of the tread and tuck in at the back. 1 to 2 in is a typical allowance; a deep nosing or thick carpet needs more.
Hollywood wraps the carpet tight over the nose and fastens it under it; waterfall drapes over the nose. Both take the same piece here. A runner is narrower than the stairs and leaves the wood showing on each side.
The width the carpet is woven in; the sample book says. Most US carpet is 12 ft, and some mills also weave 13 ft 6 in and 15 ft. Several step pieces stand side by side across it.

The number of landings of the size above (length × width). A landing is carpeted like a small room. Set 0 for none.

Carpet is cut oversize and trimmed at the walls: 3 in at each end is typical, as on the carpet calculator.
Pad goes under the carpet on the treads (wrapped over the nosing) and the landings. Leave it out for a glue-down or low-profile carpet.

Buy 14 square yards.

Buy 14 square yards

70.75 sq ft + 0% waste = 70.75 sq ft

  • Step pieces (tread + riser + nosing wrap): 13 pieces (each 19 in), 4 side by side across the roll, 4 rows, pile all one way
  • Carpet off the roll: 10 ft (roll width 12 ft)
  • Landings: 1 landing (roll 3.5 ft), included in the roll length above
  • Tack strip (4 ft lengths): 22 lengths (≈ 87 ft), two strips a step, an estimate
  • Pad (underlay): 6 square yards (≈ 51 sq ft), a piece on each tread, wrapped over the nosing, and the landings
How this number is calculated

70.75 sq ft (no waste added) ÷ 5.05 sq ft per square yard = 14 square yards

Shopping list

  • Carpet tack strip
  • Carpet stair tool
  • Stair carpet pad
  • Carpet knee kicker (stretcher)
  • Carpet utility knife and blades
  • Carpet binding tape
Show diagram

Saved projects

No saved projects yet.

Carpet for steps alone by number of steps (12 ft roll)

10 in tread, 7.5 in riser, 1.5 in nosing wrap (a 19 in piece), 36 in wide, so 4 pieces stand across a 12 ft roll. No landing and no extra percentage, worked by this calculator. Roll length is rounded up to a whole foot, and square yards = roll length × 12 ÷ 9, rounded up.
StepsPieces acrossRowsRoll for steps (ft)Roll length bought (ft)Square yards
10434.7557
12434.7557
13446.33710
14446.33710
15446.33710
16446.33710

Square yards for 13 steps by stair width and roll width

Same steps, no landing, 19 in piece, no extra percentage, worked by this calculator. A wider roll fits more pieces across, but only when the piece width divides into it well: 36 in fits 4 across a 12 ft roll, 42 in only 3.
Stair width12 ft roll13 ft 6 in roll15 ft roll
30 in10 (4 across)8 (5 across)9 (6 across)
36 in10 (4 across)11 (4 across)9 (5 across)
42 in11 (3 across)12 (3 across)12 (4 across)
48 in11 (3 across)12 (3 across)14 (3 across)

Length of the piece for one step by tread and riser

Tread plus riser plus a 1.5 in nosing wrap (typical), worked by this calculator. The last column is the continuous runner length for 13 steps in whole feet.
TreadRiserPiece (in)Piece (ft)Runner for 13 steps (ft)
9 in8 in18.5 in1.54 ft21
10 in7.5 in19 in1.58 ft21
10 in7.75 in19.25 in1.6 ft21
11 in7 in19.5 in1.63 ft22
11 in7.5 in20 in1.67 ft22

Methodology & assumptions

Stair carpet is cut from the roll as one piece per step, the way an installer plans a stair. Each piece is as long as the tread, the riser and a wrap allowance at the nosing, and as wide as the stairs (full width, wall to wall, in either the Hollywood or the waterfall style, which take the same piece) or as wide as the runner. The nosing wrap is typical at 1 to 2 in and is an estimate: it depends on the nosing, the thickness of the carpet and the style. The pile has to run the same way on every piece, so the length of each piece runs along the roll and the pieces stand side by side across the roll width: across = floor(roll width ÷ piece width), rows = ceil(steps ÷ across), and the roll length for the steps is rows × piece length. A piece wider than the roll is pieced with a seam on every step. Landings are carpeted like small rooms by the carpet calculator's method: strips the width of the roll with 3 in of trim at each end (typical), laid in whichever direction takes less roll, all one way. The roll length bought is the steps and the landings with the extra percentage, rounded up to a whole foot, and square yards are that length × roll width ÷ 9, rounded up, as on the carpet calculator. A runner is cut from the same roll by the same layout, so its square yards include the roll width left over; the runner length (steps × piece length) is also shown for a ready-bound runner sold by the foot, with the reveal of bare stair on each side. Tack strip is two strips a step, one on the tread and one on the riser, each cut 4 in shorter than a runner is wide (the stair width for a full-width cover), plus the landing edges. Guides differ here: one puts a riser strip on every step, another only for the waterfall style, so the tack strip is an estimate. Pad is a piece the width of the tack strip and 3 in deeper than the tread, per step, plus the landing area, in square yards. Staples and nails are not counted: no source gave a count per step (one guide spaces them 3 in apart under the nosing in the Hollywood style, which depends on the width). A real staircase varies from step to step, especially in an older house, so measure several and use the largest; winders and turned stairs need a drawing, not this calculator. This is a buy estimate: have the installer confirm the layout and the roll width before you order.

How to calculate how much carpet you need for stairs

  1. Measure the steps. Count the steps and measure the tread depth, the riser height and the width between the walls. Measure several steps and use the largest.
  2. Work out the piece for one step. Add the tread, the riser and about 1 to 2 in of wrap at the nosing. This is the length of one piece; its width is the stair width, or the runner width.
  3. Lay the pieces across the roll. Divide the roll width by the piece width and round down to see how many pieces stand side by side with the pile running the same way. Divide the steps by that and round up for the rows.
  4. Add the landings. Carpet each landing like a small room, with a trim allowance at each end of the strip, and add its roll length to the steps.
  5. Convert and add the supplies. Square yards = roll length × roll width ÷ 9, rounded up. Pad is a piece on each tread plus the landings, and tack strip is two strips a step.

Worked examples

ProjectResult
13 steps, 10 in tread, 7.5 in riser, 1.5 in wrap, 36 in wide, one 3 × 3 ft landing, 12 ft roll14 square yards (4 rows of 4 pieces, 10 ft off the roll, 6 square yards of pad)
The same 13 steps with no landing10 square yards (6.33 ft of roll, rounded up to 7 ft)
A 27 in runner on the same steps, cut from a 12 ft roll (estimate)7 square yards (5 pieces across; 21 ft of runner length, 4.5 in reveal each side)
Wide stairs, 48 in, 13 steps: only 3 pieces fit across a 12 ft roll11 square yards (5 rows of 3 pieces, 8 ft off the roll)
The 13 steps and landing on a 15 ft roll: 5 pieces across, but a wider roll to pay for15 square yards (3 rows of 5 pieces, 9 ft off the roll)
12 steps, 9 in tread, 8 in riser, 1.5 in wrap, 36 in wide, no landing7 square yards (18.5 in piece, 3 rows, 5 ft off the roll)
The first example in a patterned carpet (+10%, typical)15 square yards (11 ft off the roll)

Frequently asked questions

How much carpet do I need for stairs?
Cut one piece per step, as long as the tread, the riser and about 1 to 2 in of wrap at the nosing, and as wide as the stairs. For 13 steps of 10 in tread and 7.5 in riser with a 1.5 in wrap that is a 19 in piece. On a 12 ft roll four 36 in pieces stand across, so the steps take 4 rows, 6.33 ft of roll, 10 square yards. Add landings, and any extra for a pattern, to that.
Why not just multiply the stair area by a waste percentage?
Because the waste comes from the roll width and the piece layout, not a percentage. The 13 steps cover 6.9 sq yd of stair, but the roll you buy is 10 sq yd. A 42 in wide stair fits only 3 pieces across a 12 ft roll, so a 6 in wider stair costs a whole extra row.
Which way does the pile run?
Down the stairs, the same on every step, and that is how the pieces are laid out here: the length of the piece runs along the roll and the pieces stand side by side across its width. Turning pieces would let more fit, but cut-pile carpet changes shade with the pile direction, so every piece goes the same way.
What is the difference between Hollywood and waterfall?
The Hollywood (or cap-and-wrap) style pulls the carpet tight over the nosing and fastens it under the nose for a tailored look. The waterfall style lets the carpet drape over the nose and is faster, and suits thick or boldly patterned carpet. Both take about the same piece of carpet, so this calculator treats them alike: the nosing wrap is the allowance you set.
How much does the nosing wrap add?
1 to 2 in a step is a typical allowance (an estimate: it depends on the nosing and the carpet). On 13 steps, 1.5 in is 1.63 ft of piece length and 2 in is 2.17 ft. With 2 in the steps take 10 square yards instead of 10. Thick carpet needs more.
How do I work out a stair runner?
A runner covers the middle of the steps and leaves the wood showing on each side. Its length is the steps times the piece length: 13 steps of 19 in is 20.58 ft, so about 21 ft of ready-bound runner. A 27 in runner on 36 in stairs leaves a 4.5 in reveal each side. Cut from broadloom on a 12 ft roll, 5 runner pieces stand across and the steps take 7 square yards.
How do I add landings?
Enter the length and width of one landing and how many there are. A landing is carpeted like a small room, with a 3 in trim at each end (typical) on the strip: a 3 × 3 ft landing takes 3.5 ft of roll, which takes the 13 steps from 10 to 14 square yards. A landing that turns the stairs through a corner is cut with the steps beside it, so have the installer confirm it.
How much pad do I need?
One piece a step as wide as the tack strip and 3 in deeper than the tread, so it wraps the nosing, plus the landing. For the example that is 6 square yards (about 51.25 sq ft). Pad is sold in rolls, so some offcut is normal. Leave it off for glue-down or low-profile carpet.
How much tack strip do I need?
Two strips a step in one guide, one on the tread and one on the riser, each cut 4 in shorter than a runner is wide. For 13 steps that is 87 ft with a landing, about 22 four-foot lengths. It is an estimate: another guide puts a riser strip only on a waterfall stair, so check with the installer. Staples or nails are not counted.
Which roll width should I use?
Use the width the carpet is woven in: 12 ft is the common US width, and some mills also weave 13 ft 6 in and 15 ft. Four 36 in pieces fit a 12 ft roll exactly, so a wider roll does not help a 36 in stair: 13 steps and one landing take 14 square yards on 12 ft, 15 on 13 ft 6 in and 15 on 15 ft, because you pay for the whole roll width.
What if my stairs are not all the same?
Measure several steps and use the largest tread and riser; in an older house they can differ. For a 12 step stair with a 9 in tread and an 8 in riser the piece is 18.5 in and the steps take 7 square yards. Winders and turned stairs need a drawing: this calculator is for a straight run with landings.
How much extra for a patterned carpet?
Each piece may need to be longer to match the pattern repeat. 10% is a typical allowance, not a rule: the sample book gives the repeat. 10% on the example is 15 square yards instead of 14.

Handy tools

  • Stair Calculator: Find the number of steps, the exact riser height and the run from the total rise, if you are still planning the stairs.
  • Feet and Inches Calculator: Turn a tape reading such as 10 3/8" into the decimal inches the tread and riser fields take.

Related calculators