Lumber Weight Calculator: How Much Do Boards and Plywood Weigh?
Twenty 2×4s, 8 ft long (1½ × 3½ in actual), of coast Douglas-fir kiln-dried to 19% weigh about 202 lb (92 kg), or 10.1 lb (4.6 kg) each. That is 106.67 board feet, and about 13% of a typical 1,500 lb half-ton pickup payload. Pick the nominal size, length, count, species and how dry the wood is, or switch to 4 × 8 ft plywood or OSB sheets. It is an estimate: real boards vary by tree, mill and moisture, and a wet pressure-treated board weighs about 40% more than a dry one.
Figures based on the sources listed belowUpdated How we calculate
202 lb (92 kg).
202 lb (92 kg)
- Weight per piece: 10.1 lb (4.6 kg) (1.5 × 3.5 in actual, 8 ft long)
- Wood density used: 34.6 lb per cu ft (555 kg/m³), 0.292 cu ft a piece
- Board feet (nominal sizes): 106.67 board feet (nominal size × length ÷ 144, as the board foot calculator counts)
- Truck or trailer load: 13% of a 1,500 lb payload; room for about 148 pieces at this weight (passengers and gear count against payload too)
Shopping list
- Ratchet tie-down straps
- Truck bed extender for lumber
- Leather work gloves
- Plywood panel cart
- Tape measure (25 ft)
Your project
- What are you weighing?: Boards, beams or posts (dimensional lumber)
- Nominal thickness: 2× (1.5 in actual)
- Nominal width: 4 (3.5 in actual)
- Length of each piece: 8 ft
- Species: Douglas-fir (coast)
- Moisture: Kiln-dried, 19% (S-DRY / KD19 limit)
- Number of pieces or sheets: 20
- Vehicle payload (optional): 1,500 lb
Also pick up
- Ratchet tie-down straps
- Truck bed extender for lumber
- Leather work gloves
- Plywood panel cart
- Tape measure (25 ft)
Reopen this calculation: /calculators/lumber-weight/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjowLCJ3aWR0aEZ0IjowfSwiZGVkdWN0aW9ucyI6W10sIndhc3RlUGN0IjowLjEsInBhcmFtcyI6eyJwcm9kdWN0IjowLCJub21UaGlja25lc3MiOjIsIm5vbVdpZHRoIjo0LCJsZW5ndGhGdCI6OCwic3BlY2llcyI6MCwibW9pc3R1cmUiOjEsInBhbmVsIjowLCJwYW5lbFRoaWNrbmVzcyI6MSwicGllY2VzIjoyMCwicGF5bG9hZExiIjoxNTAwfX0
Saved projects
No saved projects yet.
Nominal and actual lumber sizes
| Nominal size | Actual size (dry) | In millimetres |
|---|---|---|
| 1 | 0.75 in | 19 mm |
| 2 | 1.5 in | 38 mm |
| 3 | 2.5 in | 64 mm |
| 4 | 3.5 in | 89 mm |
| 6 | 5.5 in | 140 mm |
| 8 | 7.25 in | 184 mm |
| 10 | 9.25 in | 235 mm |
| 12 | 11.25 in | 286 mm |
Weight of one board by size and length
| Size | 8 ft | 10 ft | 12 ft | 16 ft |
|---|---|---|---|---|
| 2×4 (1.5 × 3.5 in) | 10.1 | 12.6 | 15.2 | 20.2 |
| 2×6 (1.5 × 5.5 in) | 15.9 | 19.8 | 23.8 | 31.7 |
| 2×8 (1.5 × 7.25 in) | 20.9 | 26.2 | 31.4 | 41.8 |
| 2×10 (1.5 × 9.25 in) | 26.7 | 33.4 | 40 | 53.4 |
| 2×12 (1.5 × 11.25 in) | 32.5 | 40.6 | 48.7 | 64.9 |
| 4×4 (3.5 × 3.5 in) | 23.6 | 29.5 | 35.4 | 47.1 |
| 6×6 (5.5 × 5.5 in) | 58.2 | 72.7 | 87.3 | 116.4 |
Wood density by species and moisture
| Species | Specific gravity at 12% | lb/cu ft at 12% | lb/cu ft at 19% | lb/cu ft green (≈50%) | lb/cu ft treated, wet (≈75%) | Where the figure comes from |
|---|---|---|---|---|---|---|
| Douglas-fir (coast) | 0.48 | 33.6 | 34.6 | 41.8 | 48.7 | Wood Handbook value, matched in a second published copy |
| Douglas-fir (interior west) | 0.5 | 35 | 36 | 43.4 | 50.6 | Wood Handbook value, matched in a second published copy |
| Southern pine (loblolly, shortleaf) | 0.51 | 35.7 | 36.7 | 44.2 | 51.5 | Wood Handbook value, matched in a second published copy |
| Western hemlock (hem-fir) | 0.45 | 31.5 | 32.5 | 39.3 | 45.9 | Wood Handbook value, matched in a second published copy |
| Sitka spruce | 0.4 | 28 | 29 | 35.2 | 41.1 | Wood Handbook value, matched in a second published copy |
| Spruce-pine-fir (SPF, typical) | 0.41 | 28.7 | 29.7 | 36 | 42.1 | typical figure (estimate) |
| Ponderosa pine | 0.42 | 29.4 | 30.4 | 36.9 | 43 | typical figure (estimate) |
| Eastern white pine | 0.35 | 24.5 | 25.5 | 31 | 36.2 | typical figure (estimate) |
| Western redcedar | 0.32 | 22.4 | 23.3 | 28.5 | 33.3 | typical figure (estimate) |
| Redwood (old growth) | 0.4 | 28 | 29 | 35.2 | 41.1 | typical figure (estimate) |
Weight of 4 × 8 ft plywood and OSB sheets
| Thickness | Plywood lb per sq ft | Plywood lb per sheet | OSB lb per sq ft | OSB lb per sheet |
|---|---|---|---|---|
| 3/8 in | 1.1 | 35 | 1.21 | 39 |
| 1/2 in (15/32 or 1/2) | 1.5 | 48 | 1.65 | 53 |
| 5/8 in (19/32 or 5/8) | 1.8 | 58 | 1.98 | 63 |
| 3/4 in (23/32 or 3/4) | 2.2 | 70 | 2.42 | 77 |
Methodology & assumptions
Dimensional lumber: each nominal size is turned into its actual size, using the dry dressed sizes of the American Softwood Lumber Standard (PS 20): nominal 2 is 1½ in, 3 is 2½ in, 4 is 3½ in, 6 is 5½ in, 8 is 7¼ in, 10 is 9¼ in and 12 is 11¼ in, and a 1× board is ¾ in. A piece's volume is thickness × width × length ÷ 1,728 cu ft. Its density comes from the species' specific gravity at 12% moisture in the USDA Forest Products Laboratory Wood Handbook (FPL-GTR-282, 2021) and the Handbook's moisture relation: the basic specific gravity is Gb = G12 ÷ (1 + 0.265 × 0.6 × G12); at moisture content M below 30%, the specific gravity at M is Gb ÷ (1 − 0.265 × (30 − M) ÷ 30 × Gb), and above 30% (the fiber saturation point) it is Gb, because the wood has stopped swelling. Density in lb per cu ft = 62.428 × that specific gravity × (1 + M ÷ 100). At 12% this reduces to 62.428 × G12 × 1.12, so a species with G = 0.48 weighs 33.6 lb per cu ft. Weight = volume × density × number of pieces. The four moisture choices are 12% (the Wood Handbook basis), 19% (the S-DRY / KD19 limit that kiln-dried framing is sold at), green at about 50% and pressure-treated still wet at about 75%. The last two are typical figures: green lumber ranges from about 30% to over 100% with species and sapwood, and a freshly treated board of southern pine is often 75% or more. The size used is always the dry dressed size, so green and treated boards, which are a little larger when wet, are slightly under-counted; a green board is also surfaced a little oversize at the mill (1 9/16 × 3 9/16 in for a 2×4). Board feet use the board foot calculator’s own helper on the nominal sizes: nominal thickness × nominal width × length in inches ÷ 144, so a 2×4×8 is 5⅓ board feet. Plywood and OSB: the weight of a 4 × 8 ft sheet is the typical weight per square foot for its thickness from the APA Panel Design Specification (about 1.1, 1.5, 1.8 and 2.2 lb per sq ft for 3/8, 1/2, 5/8 and 3/4 in plywood) times 32 sq ft; OSB is taken as plywood plus 10%. These are typical weights: manufacturers' own data sheets and the panel's moisture will differ by a few percent. Truck or trailer load: your vehicle’s payload (the figure on the sticker in the driver’s door jamb, which already includes passengers and gear) is compared with the total, and the note shows how many pieces fit at a time. The default 1,500 lb is a typical half-ton pickup (modern half-tons run roughly 1,500 to 2,300 lb); use your own number, and treat the result as a planning estimate, never a rating, because a load over the GVWR or axle limits is unsafe whatever the payload arithmetic says. What this does not do: it does not weigh engineered lumber (LVL, glulam, I-joists), hardwoods, rough-sawn or timber over 5 in thick, or lumber with a different moisture than the four choices; for those use the supplier's weight per foot.
- USDA Forest Service, Forest Products Laboratory, Wood Handbook: Wood as an Engineering Material (General Technical Report FPL-GTR-282, 2021): the specific gravity of each domestic softwood at 12% moisture (the mechanical-properties tables of Chapter 5) and the relation between moisture content, specific gravity and density (Chapter 4, Moisture Relations and Physical Properties of Wood)
- Oregon Wood Innovation Center, Oregon State University, Table of Relative Working and Physical Properties: specific gravity at 12% moisture for western hemlock (0.45), Sitka spruce (0.40) and coast Douglas-fir (0.48), the Wood Handbook figures
- American Lumber Standard Committee / NIST, American Softwood Lumber Standard, Voluntary Product Standard PS 20: the dressed sizes of dimension lumber (2×6 = 1½ × 5½ in dry). The 3½, 7¼, 9¼ and 11¼ in sizes are from the same table; the SPIB article on lumber size categories gives the 2×6 size
- APA, The Engineered Wood Association, Panel Design Specification (Form D510): approximate dead-load weights of plywood panels in lb per sq ft by thickness, with OSB about 10% heavier. The figures here are typical weights from a published copy of that table, not a manufacturer’s data sheet
- Journal of Light Construction, Q&A: Treated Lumber’s Moisture Content: southern pine is dried to about 19% before treatment and holds about 75% moisture or more after pressure treatment. A typical figure, which falls as the lumber dries
- Estimate: the species other than coast and interior Douglas-fir, southern pine, western hemlock and Sitka spruce (SPF, ponderosa pine, eastern white pine, western redcedar and redwood) are typical specific gravities at 12% moisture, the 1,500 lb half-ton payload is a typical figure, and the 50% green moisture content is a typical figure. Your vehicle’s door-jamb sticker and owner’s manual give the real payload
How to find the weight of lumber or sheets
- Choose lumber or sheets. Pick boards, beams or posts for dimensional lumber, or plywood or OSB sheets for 4 × 8 ft panels.
- Enter the size, length and count. Choose the nominal thickness and width (2×4, 2×10, 4×4), the length of each piece and how many pieces. For sheets, choose plywood or OSB, the thickness and the number of sheets.
- Pick the species and moisture. Choose the species and whether the wood is kiln-dried, green or pressure-treated and still wet. Wet wood weighs much more.
- Read the weight. The result shows the total in pounds and kilograms, with the weight of one piece, the density used and the board feet.
- Check your load. Enter your vehicle’s payload from the door-jamb sticker to see the share of it the load uses and how many pieces fit in a trip.
Worked examples
| Project | Result |
|---|---|
| 20 pieces of 2×4, 8 ft, coast Douglas-fir, kiln-dried to 19% | 202 lb (92 kg), 10.1 lb (4.6 kg) each |
| The same studs, green (about 50% moisture) | 244 lb (110 kg), 12.2 lb (5.5 kg) each |
| 10 pieces of 2×6, 12 ft, southern pine, pressure-treated and still wet | 354 lb (161 kg), 35.4 lb (16.1 kg) each |
| The same 10 boards after drying to 19% | 253 lb (115 kg), 25.3 lb (11.5 kg) each |
| One 4×4 post, 8 ft, coast Douglas-fir at 19% | 24 lb (11 kg) |
| 12 pieces of 2×10, 16 ft, western hemlock (hem-fir) at 19% | 602 lb (273 kg), 50.1 lb (22.7 kg) each |
| 30 sheets of 1/2 in plywood, 4 × 8 ft | 1,440 lb (653 kg), 48 lb (21.8 kg) a sheet |
| 30 sheets of 3/4 in OSB, 4 × 8 ft | 2,323 lb (1,054 kg), 77.4 lb (35.1 kg) a sheet |
| 100 spruce-pine-fir 2×4s, 8 ft, at 19% (a pickup load) | 866 lb (393 kg), over a 1,500 lb payload |
Frequently asked questions
- How much does a 2×4 weigh?
- An 8 ft 2×4 of coast Douglas-fir kiln-dried to 19% weighs about 10.1 lb (4.6 kg). The same stud in a light species such as spruce-pine-fir is a little under that, in southern pine a little over, about 12 lb green, and 14 to 15 lb pressure-treated and still wet. Twenty of them weigh 202 lb (92 kg).
- What are the actual sizes of lumber?
- Lumber is named by its rough size before drying and planing. Under the American Softwood Lumber Standard (PS 20) a dry 2× is 1½ in thick, and the widths are 3½ in for a 4, 5½ for a 6, 7¼ for an 8, 9¼ for a 10 and 11¼ for a 12. A 4×4 post is 3½ × 3½ in and a 6×6 is 5½ × 5½. The calculator weighs the actual size, not the name.
- How much does wet pressure-treated lumber weigh?
- A lot more. Treatment puts water back into the wood: about 75% moisture is typical for a freshly treated southern pine board. Ten 2×6s, 12 ft long, weigh 354 lb (161 kg) wet and 253 lb (115 kg) once dried to 19%. Treated lumber sold as kiln-dried after treatment (KDAT) is closer to the dry figure. This is why a stack of treated decking is much harder to carry than the same stack of framing lumber.
- How much heavier is green lumber than kiln-dried lumber?
- Green wood still holds its sap and water. At a typical 50% moisture, the 20 studs above weigh 244 lb (110 kg), against 202 lb (92 kg) at 19%, and green lumber can be much heavier than that for wet species and sapwood. Moisture content is the water weight as a percentage of the oven-dry weight, so a board at 50% weighs about 1.5 times its dry self.
- How do you work out the weight of a board?
- Multiply the actual thickness, width and length in inches and divide by 1,728 to get cubic feet, then multiply by the wood’s density in pounds per cubic foot. A coast Douglas-fir board at 19% is about 34.6 lb per cu ft, so a 1½ × 3½ in board 8 ft long (0.29 cu ft) is about 10 lb. The calculator does this for any size, species and moisture.
- How much does a sheet of plywood or OSB weigh?
- Typical 4 × 8 ft sheets weigh about 35 lb at 3/8 in, 48 lb at 1/2 in, 58 lb at 5/8 in and 70 lb at 3/4 in for plywood, and about 10% more for OSB. Thirty 1/2 in plywood sheets weigh 1,440 lb (653 kg), and thirty 3/4 in OSB sheets 2,323 lb (1,054 kg). Panel is heavier when it is wet, and a given brand can differ by a few pounds a sheet.
- Is board feet a measure of weight?
- No. A board foot is a volume, 144 cubic inches (1 × 12 × 12 in), used for pricing lumber, and it is figured on the nominal size. The 20 studs above are 106.67 board feet, but weigh 202 lb (92 kg); the weight depends on the actual size, the species and the moisture. For a cut list priced by the board foot, use the board foot calculator.
- Can my truck carry this load?
- Check the payload on the sticker in your driver’s door jamb: it is the weight of passengers and cargo the truck can carry, and the driver and passengers use part of it. A typical half-ton pickup carries about 1,500 lb or more, so 100 SPF 2×4s at 8 ft (866 lb (393 kg)) is a heavy load for it, and the note under the result shows how many pieces fit. Do not trust a load that looks about right: weigh it, or make two trips. The tool is a planning estimate and not a rating.
- How much does a 2×10 joist weigh?
- A 16 ft 2×10 of western hemlock (hem-fir) at 19% weighs about 50.1 lb (22.7 kg), and twelve of them 602 lb (273 kg). The pieces are heavy enough that two people carry a long 2×10 or 2×12, and they are the first thing to check when loading a trailer.
- Does this work for hardwood, LVL or glulam?
- No. The species list is softwoods only, and engineered lumber such as LVL, glulam and I-joists has its own weight per foot from the maker. For hardwood weights, find the species’ density in the Wood Handbook and multiply by the board’s volume. The weight of a post or a timber over 5 in thick also depends on whether it is rough or surfaced.
Handy tools
- Board Foot Calculator: Counts board feet for a cut list, for hardwood by the 4/4 and for priced-by-the-board-foot lumber.
- Feet and Inches Calculator: Measured 9' 7 1/2"? It turns tape readings into the decimal feet the length field takes.