Log Board Feet Calculator (Doyle, Scribner, International 1/4)
A 16 ft log that measures 12 in across the small end inside the bark holds 97 board feet (International ¼) by the International ¼-inch rule, 86 by the Scribner formula and 64 by the Doyle rule: Doyle = (12 − 4)² × 16 ÷ 16 = 64. The three rules give different answers for the same log because each assumes a different amount of lumber lost to saw kerf, slabs and taper; Doyle is the lowest on small logs, 34% under International here. Enter the small-end diameter in inches, the length and the number of logs to see all three.
Figures based on the sources listed belowUpdated How we calculate
97 board feet (International ¼).
97 board feet (International ¼)
- Doyle: 64 BF
- Scribner (Decimal C formula): 86 BF; Decimal C table reads 9 (90 BF) a log
- International ¼-inch: 97 BF
- Doyle against International: Doyle scales 34% under International on this log. Mills usually saw more than Doyle scales, which is its overrun
Shopping list
- Log scale stick (Doyle, Scribner, International)
- Diameter tape (D-tape)
- Log tongs
- Timber marking paint
- Tape measure (25 ft)
Your project
- Small-end diameter inside bark: 12 in
- Log length: 16 ft
- Number of logs: 1
Also pick up
- Log scale stick (Doyle, Scribner, International)
- Diameter tape (D-tape)
- Log tongs
- Timber marking paint
- Tape measure (25 ft)
Reopen this calculation: /calculators/log-board-feet/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjowLCJ3aWR0aEZ0IjowfSwiZGVkdWN0aW9ucyI6W10sIndhc3RlUGN0IjowLjEsInBhcmFtcyI6eyJkaWFtZXRlckluIjoxMiwibGVuZ3RoRnQiOjE2LCJsb2dzIjoxfX0
Saved projects
No saved projects yet.
Board feet in a 16 ft log by the three rules
| Small-end diameter | Doyle | Scribner (formula) | International ¼ | Doyle under International |
|---|---|---|---|---|
| 6 in | 4 | 12 | 19 | 79% |
| 8 in | 16 | 31 | 39 | 59% |
| 10 in | 36 | 55 | 65 | 44% |
| 12 in | 64 | 86 | 97 | 34% |
| 14 in | 100 | 123 | 136 | 26% |
| 16 in | 144 | 166 | 181 | 20% |
| 18 in | 196 | 216 | 232 | 16% |
| 20 in | 256 | 272 | 290 | 12% |
| 22 in | 324 | 334 | 354 | 8% |
| 24 in | 400 | 403 | 424 | 6% |
| 28 in | 576 | 559 | 585 | 1% |
| 32 in | 784 | 741 | 770 | -2% |
Doyle board feet by diameter and length
| Small-end diameter | 8 ft | 10 ft | 12 ft | 14 ft | 16 ft |
|---|---|---|---|---|---|
| 6 in | 2 | 3 | 3 | 4 | 4 |
| 8 in | 8 | 10 | 12 | 14 | 16 |
| 10 in | 18 | 23 | 27 | 32 | 36 |
| 12 in | 32 | 40 | 48 | 56 | 64 |
| 14 in | 50 | 63 | 75 | 88 | 100 |
| 16 in | 72 | 90 | 108 | 126 | 144 |
| 18 in | 98 | 123 | 147 | 172 | 196 |
| 20 in | 128 | 160 | 192 | 224 | 256 |
| 22 in | 162 | 203 | 243 | 284 | 324 |
| 24 in | 200 | 250 | 300 | 350 | 400 |
| 28 in | 288 | 360 | 432 | 504 | 576 |
| 32 in | 392 | 490 | 588 | 686 | 784 |
Scribner (formula) board feet by diameter and length
| Small-end diameter | 8 ft | 10 ft | 12 ft | 14 ft | 16 ft |
|---|---|---|---|---|---|
| 6 in | 6 | 8 | 9 | 11 | 12 |
| 8 in | 15 | 19 | 23 | 27 | 31 |
| 10 in | 28 | 34 | 41 | 48 | 55 |
| 12 in | 43 | 54 | 64 | 75 | 86 |
| 14 in | 61 | 77 | 92 | 107 | 123 |
| 16 in | 83 | 104 | 125 | 145 | 166 |
| 18 in | 108 | 135 | 162 | 189 | 216 |
| 20 in | 136 | 170 | 204 | 238 | 272 |
| 22 in | 167 | 209 | 251 | 293 | 334 |
| 24 in | 202 | 252 | 302 | 353 | 403 |
| 28 in | 280 | 350 | 420 | 489 | 559 |
| 32 in | 370 | 463 | 556 | 648 | 741 |
International ¼-inch board feet by diameter and length
| Small-end diameter | 8 ft | 10 ft | 12 ft | 14 ft | 16 ft |
|---|---|---|---|---|---|
| 6 in | 8 | 10 | 13 | 16 | 19 |
| 8 in | 17 | 22 | 27 | 33 | 39 |
| 10 in | 29 | 37 | 46 | 55 | 65 |
| 12 in | 44 | 57 | 69 | 83 | 97 |
| 14 in | 63 | 80 | 98 | 117 | 136 |
| 16 in | 84 | 108 | 131 | 156 | 181 |
| 18 in | 109 | 139 | 169 | 200 | 232 |
| 20 in | 137 | 174 | 212 | 251 | 290 |
| 22 in | 169 | 214 | 259 | 307 | 354 |
| 24 in | 203 | 257 | 311 | 368 | 424 |
| 28 in | 282 | 356 | 430 | 507 | 585 |
| 32 in | 373 | 471 | 568 | 669 | 770 |
Scribner Decimal C: how a log is rounded
| Small-end diameter | Formula board feet | Decimal C reading | Board feet it stands for |
|---|---|---|---|
| 8 in | 31 | 3 | 30 |
| 10 in | 55 | 6 | 60 |
| 12 in | 86 | 9 | 90 |
| 14 in | 123 | 12 | 120 |
| 16 in | 166 | 17 | 170 |
| 20 in | 272 | 27 | 270 |
| 24 in | 403 | 40 | 400 |
Methodology & assumptions
A log rule estimates the lumber a log will saw into, in board feet (a board foot is 144 cubic inches of lumber, 1 in × 12 in × 12 in). Every rule starts from the same two measurements: D, the diameter in inches across the small end of the log inside the bark, and L, the length in feet. Doyle: board feet = (D − 4)² × L ÷ 16. It deducts 4 in from the diameter for slab and saw kerf, squares what is left, and has no allowance for taper; it is zero at or below 4 in. Scribner: the Scribner rule is a diagram drawn in 1846 by J. M. Scribner (circles with 1 in boards drawn in them, less slabs and kerf) and is printed as a table, now mostly in Scribner Decimal C. This page uses the formula that closely follows it, board feet = (0.79 D² − 2 D − 4) × L ÷ 16, never below zero. It is a fitted formula, not the rule itself, and in the Scribner Decimal C table each log is rounded to the nearest 10 board feet and written in tens (the zero is dropped), so the table reads 9 for the formula's 86 board feet on a 12 in, 16 ft log, meaning 90. The 12 in, 16 ft log is 80 on the published Scribner table, so expect the formula to run a few percent above the table, more on small logs. International ¼-inch: the rule J. F. Clark derived allows a ¼ in saw kerf and ½ in of taper for every 4 ft of length. For a 4 ft section of small-end diameter d, Clark's formula gives 0.22 d² − 0.71 d board feet; the ¼ in kerf version multiplies that by 0.905, which is the same as 0.199 d² − 0.642 d. A longer log is worked as a stack of 4 ft sections from the small end, each section ½ in larger in diameter than the one before it, and the sections are added. For a 16 ft log that comes to 0.796 D² − 1.375 D − 1.23. A last section shorter than 4 ft is counted pro rata, which is this page's choice for part sections; tables are printed only for set lengths. The International result is the headline, because it is the closest to what a sawmill cuts, and is shown beside the other two. Totals for several logs are the one-log figure times the count. Overrun: a mill that saws more lumber than the log rule scaled has overrun, and a rule that scales low has more of it. Doyle scales small logs low, so the same 12 in log that Doyle scales as 64 board feet is likely to saw out near the International figure of 97. The sawyer's own kerf, the mill's recovery and how the lumber is trimmed decide the real yield; no rule predicts it exactly, so use the numbers to compare offers made on the same rule, not to promise a yield. What this does not do: it does not scale for defects (rot, crook, sweep, shake), measure by the log's average or large-end diameter, deal with logs scaled by weight or cubic volume, or work from a standing tree.
- Virginia Cooperative Extension, Forest Landowner’s Guide to the Measurement of Timber and Logs (publication 420-085, James E. Johnson, revised by Jennifer Gagnon): a 12-inch, 16-foot log is 95 board feet by International ¼, 80 by Scribner and 64 by Doyle. Used here as a check on the three formulas
- University of Tennessee Extension, Understanding Log Scales and Log Rules (PB 1650): the Doyle, Scribner Decimal C and International ¼-inch rules, Doyle having no allowance for taper and scaling small logs low and large logs high
- Purdue Extension, Log and Tree Scaling Techniques (FNR-191): Doyle = (D − 4)² × L ÷ 16 with D the small-end diameter inside bark, Doyle and International as formula rules, the Scribner rule first published in 1846
- USDA Forest Service, National Forest Log Scaling Handbook (FSH 2409.11): Scribner Decimal C is rounded to the nearest 10 board feet with the last digit dropped, and has no taper allowance, so it underestimates logs over 16 ft
- Estimate: the Scribner formula (0.79 D² − 2 D − 4) × L ÷ 16 and the International formula (Clark’s 0.22 d² − 0.71 d for a 4 ft section, times 0.905 for ¼ in kerf, with ½ in of taper per section) are published formula forms of table rules, as given in extension handouts and calculators. They agree with the printed tables to within a few percent on medium and large logs and run higher on small ones. The scaling rule written into your contract or sale governs
How to find the board feet in a log
- Measure the small end. Measure across the small end of the log, inside the bark, in inches, and measure the log length in feet.
- Enter the diameter and length. Type the diameter in inches and the length. Switch the length to metres if you measured in metres; the diameter stays in inches.
- Enter how many logs. Set the number of identical logs to get the total board feet of the pile or load.
- Compare the three rules. Read Doyle, Scribner and International ¼ side by side. The headline is the International figure, closest to what a mill cuts.
- Use the same rule for every price. Compare offers only on one rule. If a buyer scales by Doyle, expect your small logs to scale low.
Worked examples
| Project | Result |
|---|---|
| One log, 12 in small end, 16 ft long | 97 board feet (International ¼); Doyle 64, Scribner 86 |
| One small log, 8 in, 16 ft | 39 board feet (International ¼); Doyle 16, Scribner 31 |
| One large log, 24 in, 16 ft | 424 board feet (International ¼); Doyle 400, Scribner 403 |
| One 14 in log, 8 ft long | 63 board feet (International ¼); Doyle 50, Scribner 61 |
| A load of 20 logs, 16 in, 12 ft | 2,618 board feet (International ¼); Doyle 2,160, Scribner 2,494 |
Frequently asked questions
- How many board feet are in a log?
- It depends on the rule used to scale it. A 16 ft log, 12 in across the small end inside the bark, is 64 board feet by Doyle, 86 by the Scribner formula and 97 by International ¼. Published extension tables give 64, 80 and 95. Always ask which rule a quote uses before comparing prices.
- What is the Doyle log rule formula?
- Board feet = (D − 4)² × L ÷ 16, where D is the small-end diameter inside bark in inches and L is the length in feet. For a 16 ft log it is simply (D − 4)². It has no allowance for taper, and the 4 in it deducts is the same for every log.
- Why does Doyle scale small logs so low?
- Because the 4 in deduction is a fixed amount, it takes a larger share of a small log. An 8 in, 16 ft log is 16 board feet by Doyle against 39 by International, 59% less, while a 24 in log is 400 against 424, only 6% less. A 6 in log scales 4 board feet by Doyle and 19 by International. The mill that saws more than the log rule predicted has overrun, so when logs are bought by Doyle the sawmill usually cuts more than was paid for, and the difference is biggest on small logs.
- Is the Scribner formula the same as the Scribner rule?
- No. The Scribner rule is a diagram, and the Scribner Decimal C table is its printed form, rounded to the nearest 10 board feet with the zero dropped, so 86 board feet is written 9. The formula (0.79 D² − 2 D − 4) × L ÷ 16 is a close fit to it, not the rule itself, and runs a few percent above the printed table on small and medium logs. Use the table your buyer uses for a sale.
- How does the International ¼-inch rule handle taper?
- It treats the log as a stack of 4 ft sections from the small end. Each section is allowed ½ in more diameter than the one below it, and each is scaled with 0.22 d² − 0.71 d (times 0.905 for a ¼ in saw kerf). The sections are added. Doyle and Scribner give no allowance for taper, so on a log longer than 16 ft they scale low where International does not.
- Which log rule should I use?
- The one written in the sale agreement, or the local custom. Doyle is the most common rule for hardwood sawlogs in Tennessee and much of the eastern US, Scribner Decimal C is the Forest Service’s default on national forests and common in the West, and International ¼ is used where a buyer wants the figure nearest to what a mill cuts. For your own comparison, International is the most realistic of the three.
- How do I measure the diameter of a log?
- Measure across the small end of the log, inside the bark, in inches, in a straight line through the center. Take two measurements at right angles and average them if the end is not round. Whether a part inch is rounded down or taken as measured is set by the scaling rule in the sale agreement, so ask.
- How many board feet are in a truckload of logs?
- Set the number of logs. Twenty logs of 16 in, 12 ft long, are 2,618 board feet (International ¼) (2,160 by Doyle and 2,494 by the Scribner formula). Then compare prices per thousand board feet only on the same rule; a price on Doyle is not the same price as one on International.
- What about logs shorter than 16 ft?
- Doyle and Scribner scale straight with length: an 8 ft log is half a 16 ft log of the same diameter. International works in 4 ft sections, so a 14 in, 8 ft log is 63 board feet and the same log at 16 ft is 136, a little more than twice, because the second 8 ft has a larger diameter in the rule. Lengths that are not a multiple of 4 ft are worked pro rata here.
Handy tools
- Board Foot Calculator: Counts board feet in sawn boards for a cut list, once the logs have been milled to lumber.
- Feet and Inches Calculator: Measured a length as 12' 6"? It turns a tape reading into the decimal feet the log length takes.