Skip to main content
ponderloop

Epoxy Resin Calculator

Resin volume = length × width × depth (for a river table, the river’s share of the slab), converted at 231 cubic inches per US gallon, plus 10% for overflow. A 72 × 24 in river table slab, 2 in thick, with the river taking 30% of its 1,728 sq in, holds 1,036.8 cu in. With 10% overflow (an estimate), that is 4.94 US gal (632 fl oz, 18.7 L) of mixed resin. At a 2:1 ratio by volume that is 3.29 US gal (421 fl oz, 12.46 L) of Part A and 1.65 US gal (211 fl oz, 6.23 L) of Part B. A deep-pour epoxy takes about 2 in per pour, so it goes in 1 pour, and the cheapest kits are 1 × 2 gal + 1 × 3 gal (5 gal of mixed resin, about $400 at typical prices). Pour depths, ratios and prices are typical figures: your product’s data sheet wins.

Figures based on the sources listed belowUpdated How we calculate

Overflow and waste (estimate)
A river table only needs resin for the river, not the whole slab. A flood coat covers the whole top at its thickness. For coasters and castings, enter one piece and the number of pieces.

The long side of the slab, tabletop, mold or one coaster. Not used when you enter the river as width × length.

The short side. For a round coaster or tabletop enter the diameter here and as the length, and pick the round outline below.
A round piece holds about 21% less than the square around it.

Measure or sketch the gap between the two halves, then divide its area by the slab’s. A narrow river is 15 to 25%; a wide one is 40% or more. An estimate until you have laid out the slabs.

The slab thickness for a river table, the mold depth for a casting, or the coat thickness for a flood coat (1/8 in is 0.125 in, about 3 mm).

Coasters or castings of the same size. Leave 1 for a table.
Typical maker figures: tabletop epoxy 1/8 to 1/4 in per coat, casting resin 1 in, deep-pour epoxy 2 in. Your product’s data sheet wins; pick Other to enter it.
By volume, as printed on the label: 1:1 for most tabletop and some casting resins, 2:1 for many deep-pour resins, 3:1 for a few. Mix exactly as labelled.

From the data sheet (9.2 lb/gal is 1.1 g/cm³). Typical resins are about 1.1 to 1.2. Enter 0 to use 1.1.

Hardeners are usually a little lighter than the resin, about 0.98 to 1.05. Enter 0 to use 1.1. A mix of the two comes to about 1.1 g/cm³, a typical figure.

4.94 US gal (632 fl oz, 18.7 L).

4.94 US gal (632 fl oz, 18.7 L)

  • Volume before overflow: 1,036.8 cu in = 4.49 US gal (575 fl oz, 16.99 L)
  • Mix ratio 2:1 by volume: Part A 3.29 US gal (421 fl oz, 12.46 L) + Part B 1.65 US gal (211 fl oz, 6.23 L) (2 parts A to 1 parts B)
  • By weight: Part A 14.33 kg (31.59 lb) + Part B 6.42 kg (14.15 lb), 20.74 kg (45.73 lb) in all; mixed density about 1.11 g/cm³ (estimate from the densities entered)
  • Pour in layers: 1 pour: 2 in is within 2 in for deep-pour epoxy
  • Kits to buy (cheapest set): 1 × 2 gal + 1 × 3 gal (5 gal of mixed resin, about $400 at typical prices)

Shopping list

  • Deep-pour epoxy resin kit
  • Tabletop epoxy kit
  • Graduated mixing cups
  • Digital scale (0.1 g)
  • Silicone mold release tape
  • Epoxy tint pigment

Saved projects

No saved projects yet.

Resin for a tabletop flood coat by size and coat thickness

Worked by this calculator: length × width × coat thickness, 10% overflow, in US fluid ounces of mixed resin (128 fl oz = 1 US gal). A 1/8 in coat is about 10 fl oz per sq ft before overflow, or about 12.8 sq ft per US gallon.
Top1/16 in coat1/8 in coat1/4 in coat
Coaster, 4 × 4 in0.6 fl oz1.2 fl oz2.4 fl oz
Cutting board, 12 × 18 in8.2 fl oz16.5 fl oz32.9 fl oz
Bar top, 24 × 72 in65.8 fl oz131.7 fl oz263.3 fl oz
Desk, 30 × 60 in68.6 fl oz137.1 fl oz274.3 fl oz
Dining table, 40 × 72 in109.7 fl oz219.4 fl oz438.9 fl oz
Conference table, 48 × 120 in219.4 fl oz438.9 fl oz877.7 fl oz

Resin for a 2 in thick river table by slab size and river share

Worked by this calculator: river area as a share of the slab outline × 2 in, 10% overflow, in US gallons of mixed resin. The river share is an estimate until you lay the slabs out: narrow is 15%, wide is 50%.
Slab15% river30% river50% river
Side table, 48 × 18 in1.23 gal2.47 gal4.11 gal
Coffee table, 48 × 24 in1.65 gal3.29 gal5.49 gal
Console, 60 × 16 in1.37 gal2.74 gal4.57 gal
Dining table, 72 × 38 in3.91 gal7.82 gal13.03 gal
Dining table, 96 × 40 in5.49 gal10.97 gal18.29 gal

Typical maximum depth per pour by epoxy type

Typical figures from maker data sheets (see the sources). Deeper pours trap heat and can crack, yellow or smoke, so these are limits, not targets. A small mass may allow less than a large one, and your data sheet wins.
Epoxy typeTypical maximum per layerMaker figures foundUsed for
Tabletop or coating epoxy1/8 in (some to 1/4 in)TotalBoat TableTop 1/8 to 1/4 in; Stone Coat Countertop Epoxy no more than 1/8 inA flood coat or thin seal coat over a finished top
Casting resin1 inTotalBoat ThickSet up to 1 in; Stone Coat Casting Resin 1/2 to 1 inCoasters, jewelry, small molds, and the first fill of a shallow river
Deep-pour epoxy2 inTotalBoat Fathom up to 2 in for river tables and slab pours; Stone Coat Super Cast up to 2 in; Epilogue EPI-POUR 2 inMost river tables and thick castings

Methodology & assumptions

Volume is the footprint times the depth times the number of pieces, in cubic inches. The footprint is length × width for a rectangle and π ÷ 4 × length × width for a round or oval piece; for a river table it is the river’s share of the slab outline (the percentage you enter), or the river’s average width × its length. Cubic inches convert with the exact definitions 1 US gallon = 231 cubic inches = 128 US fluid ounces = 3.785411784 litres. The overflow allowance (0%, 10% or 20%) is added to that volume and is an estimate, not a published figure. The mixed resin is split by volume into Part A and Part B in the ratio you pick (1:1, 2:1, 3:1 or custom). By weight, each part’s volume is multiplied by its density in g/cm³ (1 cu in = 16.387 cm³): the defaults, 1.15 for Part A and 1.03 for Part B, are the TotalBoat ThickSet figures and give a mixed density near 1.1 g/cm³, a typical value (the cured Fathom resin is listed at 1.11 g/cm³); enter your data sheet’s numbers for better weights, and use the weight ratio the label prints if it has one. The depth of one layer is limited by the epoxy type: about 1/8 in for tabletop and coating epoxy, 1 in for casting resin and 2 in for deep-pour epoxy, which are typical maker figures (see the table and sources) and not rules; pick Other to enter the figure on your data sheet. Layers are the depth divided by that limit, rounded up, poured as equal layers. Kits are the cheapest combination of 1 qt, 1 gal, 2 gal and 3 gal kits (A and B together) that holds the resin, using typical shelf prices (1 qt $45, 1 gal $90, 2 gal $165, 3 gal $235), which are estimates and change often. A river table has details the calculator cannot know: an uneven underside, voids and knots that soak up resin, and a mold that leaks. The result is an estimate, so mix a small extra batch. Metric: each dimension field has its own unit picker (in, cm, mm, ft or m), and volumes are shown in both US and metric units. This calculator is for casting and coating with epoxy; for coating a garage floor, see the epoxy floor calculator.

How to calculate how much epoxy resin a project needs

  1. Pick the project. Choose a river table, a flood coat, a casting or coasters. For a river table, give the river as a share of the slab or as its average width and length.
  2. Enter the size and depth. Enter the length, width and depth or thickness in inches, centimetres or millimetres. For a coaster or casting, enter one piece and the number of pieces; pick round for a round piece.
  3. Add overflow. Add 10% for resin left in the cup and a pour that fills a little high, or 20% for a leaky mold or a live edge with voids.
  4. Choose the mix ratio and the epoxy type. Pick the 1:1, 2:1 or 3:1 ratio printed on the label, or a custom one, and the type of epoxy so that the depth per pour is right. The calculator splits the resin into Part A and Part B, by volume and by weight.
  5. Plan the layers and the kits. Read the number of layers and the resin for each, then the cheapest set of kits. Mix one layer at a time, and follow the data sheet for the time between pours.

Worked examples

ProjectResult
72 × 24 in river table, 2 in thick, river 30% of the slab, deep-pour epoxy 2:1, 10% overflow1,036.8 cu in net → 4.94 US gal (632 fl oz, 18.7 L)
River 96 in long and 5 in wide, 2 in thick, deep-pour epoxy 2:1, 10% overflow960 cu in net → 4.57 US gal (585 fl oz, 17.3 L)
48 × 30 in tabletop flood coat, 1/8 in thick, tabletop epoxy 1:1, 10% overflow180 cu in net → 0.86 US gal (110 fl oz, 3.2 L)
Twelve 4 in round coasters, 1/4 in deep, casting resin 1:1, 20% overflow37.7 cu in net → 0.2 US gal (25 fl oz, 0.7 L)
12 × 12 in mold, 3 in deep, casting resin 1:1, 10% overflow432 cu in net → 2.06 US gal (263 fl oz, 7.8 L), 3 layers

Frequently asked questions

How much epoxy do I need for a river table?
Only the river needs resin, not the whole slab. Multiply the river’s length, average width and the slab thickness. A 72 × 24 in slab 2 in thick with a river that is 30% of its area holds 1,036.8 cu in, which is 4.94 US gal (632 fl oz, 18.7 L) with 10% overflow. A table with a wide river, a live edge that leaks, or a mold that is not perfectly sealed needs more; the 20% option is for those.
How do I convert cubic inches to gallons of epoxy?
Divide by 231: a US gallon is exactly 231 cubic inches (that is 128 US fluid ounces, or 3.785 litres). So 1,000 cu in is 4.33 gal, or about 554 fl oz. Cubic feet convert at 7.48 gal, and one cubic inch is about 16.4 mL.
How deep can I pour epoxy in one layer?
It depends on the product, not the project. Tabletop and coating epoxies are typically poured 1/8 in thick (TotalBoat TableTop lists 1/8 to 1/4 in; Stone Coat’s countertop epoxy asks for no more than 1/8 in). Casting resins are typically up to 1 in. Deep-pour epoxies are typically up to 2 in per pour (TotalBoat Fathom, Stone Coat Super Cast, Epilogue EPI-POUR). A thicker pour makes more heat as it cures and can crack, yellow or smoke, so a thick river table is poured in layers. Check your resin’s data sheet and choose “Other” to enter its figure.
What is the difference between 1:1, 2:1 and 3:1 epoxy?
It is the mix ratio of Part A (resin) to Part B (hardener) by volume. Tabletop and many casting resins are 1:1, many deep-pour resins are 2:1 (TotalBoat Fathom and Stone Coat Super Cast are 2:1 by volume), and a few are 3:1. Epoxy cures by chemistry, so the ratio is not a preference: a wrong ratio stays tacky or soft. Measure by volume in a graduated cup, or by weight on a scale, and mix exactly what the label says.
How do I measure epoxy by weight instead of volume?
Multiply each part’s volume by its density. The calculator uses the densities you enter (1.15 g/cm³ for Part A and 1.03 g/cm³ for Part B are the TotalBoat ThickSet figures), which give a mixed density near 1.1 g/cm³, a typical figure. For the default river table that is Part A 14.33 kg (31.59 lb) and Part B 6.42 kg (14.15 lb). Makers often print a weight ratio next to the volume ratio (TotalBoat Fathom is 2:1 by volume and 100:44 by weight), so use that one if your label has it.
How many layers will my pour need?
Divide the depth by the product’s maximum pour and round up. A 3 in casting in a 1 in casting resin is 3 layers of 1 in, about 87.8 fl oz (2,596 mL) of resin each (2.06 US gal (263 fl oz, 7.8 L) in all). The same 3 in in a 2 in deep-pour epoxy is 2 layers. Between layers, follow the data sheet: some say to pour the next layer once the last has cooled, others while it is still slightly tacky, so that they bond.
How much extra should I mix for overflow?
About 10% is a common allowance for resin left on the cup and mixing stick, a slightly uneven slab, and a pour that fills a bit past the line. A mold that leaks, a live edge with deep voids, or sealing a porous wood may need 20%. These are rules of thumb, not published figures. It is better to mix a small extra batch than to run out part-way through a pour, because a layer will not bond well if the one below has cured too far.
Which kit sizes should I buy?
The calculator finds the cheapest mix of 1 qt, 1 gal, 2 gal and 3 gal kits that holds your amount, from typical shelf prices (an estimate: larger kits cost less per gallon). For the default river table that is 1 × 2 gal + 1 × 3 gal (5 gal of mixed resin, about $400 at typical prices). Buying a little more than you need is usual, because kits come in fixed sizes. Kit sizes and prices differ by brand.

Handy tools

  • Unit Converter: Convert the result to another volume unit (cubic inches, fluid ounces, quarts, litres) or a size from inches to millimetres.

Related calculators