Skip to main content
ponderloop

Aquarium Calculator: Gallons, Weight, Heater Size and Filter Flow

A 40 gallon breeder (36 × 18 × 16 in inside) filled to 1 in below the rim over 2 in of gravel holds 36.5 US gal (138 L). That is 36 × 18 × 13 in of water = 8,424 cubic inches, divided by 231 cubic inches per gallon. Filled with that water and the gravel it weighs about 382 lb before the glass and stand, and needs a heater of roughly 125 W and a filter rated for about 146 to 219 gal/h (typical figures). Enter the inside size, the fill level and the substrate depth.

Figures based on the sources listed belowUpdated How we calculate

A bow-front is treated as a rectangle (length × width, the straight part) plus a half ellipse across the front, as long as the tank and as deep as the bow. Real bows are a circular arc or a flatter curve, so this is an approximation: use the inside dimensions.

Inside height from the bottom glass to the top of the tank (the rim). A 40 gallon breeder is 16 in; a 55 gallon is 21 in. Inside dimensions are about 1/4 to 1/2 in smaller each way than the outside because of the glass.

Most tanks are filled an inch or so below the rim (more under a rimless lid or for a jumpy fish). Water height is the tank height minus this gap minus the substrate.

Gravel or sand laid on the bottom. It takes up room, so its depth is taken off the water height. Water in the gaps between the stones is not added back, so the water figure is a little low.
Sets the weight per cubic foot (about 104 lb for gravel, 100 lb for sand, a planning figure). Light materials such as volcanic or plant-soil substrates weigh much less: use the bag label.
Typical bag sizes for aquarium gravel and sand; pick the one you will buy. Check the weight printed on the bag.
Saltwater is about 2.5% heavier than fresh water at a specific gravity of 1.025.

The coolest the room gets where the tank stands, in °F (68 °F is 20 °C). The heater has to cover that gap.

In °F (78 °F is about 25.6 °C), a common setting for tropical fish. Use what your livestock needs.

36.5 US gal (138 L).

36.5 US gal (138 L)

  • Tank capacity to the rim (no substrate): 44.9 US gal (170 L)
  • Water in imperial gallons: 30.4 imperial gal
  • Filled weight, water and substrate only (fresh water, 8.34 lb/gal): about 382 lb (173 kg), plus the empty tank, stand and equipment (water alone 304 lb (138 kg))
  • Heater (rule of thumb, estimate): about 125 W (3 W per gal for a 10 °F rise); a cold, drafty spot needs more
  • Filter flow, 4 to 6 times the water per hour (typical): about 146 to 219 gal/h (552 to 828 L/h), rated flow with the media clean
  • Gravel to buy (estimate): about 78 lb (35 kg): 4 bags of 20 lb

Shopping list

  • Aquarium heater
  • Aquarium thermometer
  • Aquarium filter
  • Aquarium gravel (20 lb)
  • Aquarium sand
  • Aquarium stand
  • Water conditioner
  • Tape measure
Show diagram

Saved projects

No saved projects yet.

Common tank sizes: water, filled weight and heater

Worked by this calculator from typical listed outside sizes in inches (the inside is a little smaller, so real figures are a few percent lower), with 1 in below the rim, 2 in of gravel, fresh water and a heater for a 10 °F rise. "To the rim" is the capacity with no substrate. Weight is the water plus dry gravel, not the glass or stand.
TankSize (in)To the rim (US gal)Water (US gal)Water and gravel (lb)Heater (W)
10 gallon20 × 10 × 1210.47.88925
20 gallon high24 × 12 × 1619.916.217050
20 gallon long30 × 12 × 1218.71416050
29 gallon30 × 12 × 1828.123.423875
40 gallon breeder36 × 18 × 1644.936.5382125
55 gallon48 × 13 × 2156.748.6480150
75 gallon48 × 18 × 2178.567.3665225
125 gallon72 × 18 × 22123.4106.61,045325

Heater watts by water volume and temperature rise (estimate)

Water temperature above the room temperature, in °F. Rule of thumb: 0.3 W per gallon for each °F of rise, held between 3 and 5 W per gallon, rounded up to the next 25 W. Add margin for a cold or drafty spot.
Water volume10 °F rise15 °F rise20 °F rise
10 gal of water50 W50 W50 W
20 gal of water75 W100 W100 W
40 gal of water125 W200 W200 W
55 gal of water175 W250 W275 W
75 gal of water225 W350 W375 W
125 gal of water375 W575 W625 W

Filter flow at 4 to 6 times the water per hour (typical)

Rated filter flow to look for, in gallons and litres per hour, worked from the water volume. Treat it as typical, not a rule.
Water volumeUS gal per hourLitres per hour
10 gal of water40 to 60151 to 227
20 gal of water80 to 120303 to 454
40 gal of water160 to 240606 to 908
55 gal of water220 to 330833 to 1,249
75 gal of water300 to 4501,136 to 1,703
125 gal of water500 to 7501,893 to 2,839

Gravel and sand for a 16 in tank by depth

Dry weight in lb of gravel at 1, 2 and 3 in deep, and of sand at 2 in (planning densities of about 104 and 100 lb per cu ft). Bags are typically 5 to 50 lb: divide and round up.
Tank footprintGravel, 1 inGravel, 2 inGravel, 3 inSand, 2 in
20 gallon long (30 × 12 in)22436542
40 gallon breeder (36 × 18 in)397811775
55 gallon (48 × 13 in)377511272
75 gallon (48 × 18 in)52104156100

Methodology & assumptions

Water volume = tank floor area × water height, converted to gallons. The shapes use the tank's inside dimensions: a rectangular tank is length × width; a cylinder is π × (diameter ÷ 2)²; a bow-front is approximated as a rectangle plus a half ellipse across the front. The rectangle is the straight part (length × width), and the half ellipse is as wide as the tank and as deep as the bow, so its area is π ÷ 4 × length × bow depth. This is an approximation: real bow fronts are usually an arc of a circle or a flatter curve, so measure the bow depth carefully and treat the result as an estimate. Water height = inside height of the tank, minus the gap between the water and the rim, minus the substrate depth. The substrate's depth is taken off whole, because stones and sand occupy that layer; the water that fills the gaps between them is not added back, and neither are rocks, wood or equipment taken out, so a tank's real water volume is a little different. For the default 36 × 18 × 16 in tank with 1 in below the rim and 2 in of gravel that is 36.5 US gallons of water against 44.9 gallons to the brim, and with 3 in below the rim instead it is 30.9 US gal (117 L). A US gallon is exactly 231 cubic inches, so 1 cu ft = 1,728 ÷ 231 = 7.48052 US gal; 1 US gal = 3.785411784 L; an imperial gallon is 4.54609 L (the imperial figure is listed under the result). Tank labels such as "40 gallon" are nominal and are worked from the outside size or a rounded capacity, so the inside dimensions give a lower number than the label. Filled weight: fresh water is taken as 8.34 lb per US gallon, and saltwater at a specific gravity of 1.025 as 8.34 × 1.025 = 8.55 lb per gallon (a 2.5% increase; real seawater varies with temperature and salinity). The substrate is added dry, at the bulk densities used by the gravel and sand calculators on this site: gravel 1.4 tons per cubic yard = 103.7 lb per cu ft, sand 1.35 tons per cubic yard = 100 lb per cu ft. These are planning figures for ordinary dry gravel and sand; aquarium gravel, coated gravel and sand differ from them, and volcanic rock or plant soil substrates are much lighter, so check the weight on the bag. The glass or acrylic, stand, hood, filter, rockwork and decor are not included, and neither are the pore water in the substrate and the water in the filter, so add them for the load on the floor. Stand: use a stand rated for the tank's filled weight, set it level on a floor that can carry it (a 75 gallon tank, water and gravel, is 665 lb before glass), and for a big tank check the floor structure; the maker's rated load wins over anything here. Heater (rule of thumb, an estimate): the common rule is 3 to 5 watts per gallon, more where the room is colder. This calculator scales it with the temperature rise: watts per gallon = 0.3 × (water temperature − room temperature in °F), held between 3 and 5, times the gallons of water, rounded up to the next 25 W. The anchor is Fluval's published E series ratings, 100 W for tanks up to 30 US gal, 200 W up to 65 gal and 300 W up to 100 gal, which are 3.0 to 3.3 W per gallon for the 68 °F room and 78 °F water that Fluval's manual assumes, a 10 °F rise; the rise-based scaling above that is this page's own way of following the 3 to 5 rule, not a manufacturer table. A tank in a cold room, near a window or door, or on an outside wall needs more, and two smaller heaters (each half the total, at opposite ends) are a common safety choice, because if one sticks on or fails the other keeps the tank from swinging. Filter flow (typical, an estimate): the usual advice is to turn the tank's water through the filter 4 to 6 times an hour, so a 36 gallon tank wants a filter rated for about 146 to 219 gal/h. Advice varies by tank (LiveAquaria gives about 4 times an hour as an average; heavily stocked and reef tanks are often run higher, planted tanks lower), and a filter delivers less than its rated flow once the media is dirty or the hose is long, so the rating is a ceiling, not the flow you will get. Substrate: volume = floor area × substrate depth, weight = volume × the bulk density above, bags = weight ÷ bag size, rounded up. Inches and the metric toggle: the tank length and width are typed in inches (in cm under the metric toggle, like the height, diameter and depths); an old shared link or saved calculation that stored feet opens at the same size; the temperatures stay in °F (68 °F is 20 °C, 78 °F is 25.6 °C). This is planning arithmetic: it does not cover stocking levels, water chemistry or cycling.

How to work out the volume, weight, heater and filter for an aquarium

  1. Measure the inside of the tank. Measure the inside length, width (front to back) and height. For a cylinder, measure the diameter; for a bow-front, the straight part and how far the front bulges.
  2. Set the fill level and substrate. Enter how far below the rim the water stands and the depth of gravel or sand. The calculator subtracts both from the height to get the water height.
  3. Read the gallons and litres. Floor area × water height ÷ 231 cubic inches gives US gallons; litres and imperial gallons are shown too.
  4. Check the weight. Pick fresh or saltwater and the substrate. Water at 8.34 lb per gallon (8.55 salt) plus the dry substrate is the filled weight, before the glass and stand.
  5. Size the heater, filter and substrate. Enter the room and water temperatures for the heater, and the bag size for the gravel. The filter is 4 to 6 times the water per hour. All three are estimates.

Worked examples

ProjectResult
40 gallon breeder, 36 × 18 × 16 in inside, 1 in below the rim, 2 in of gravel36.5 US gal (138 L), 44.9 gal to the rim
55 gallon, 48 × 13 × 21 in, freshwater, 2 in of gravel48.6 US gal (184 L), about 480 lb filled
The same 55 gallon as a saltwater tank (specific gravity 1.025)48.6 US gal (184 L), about 491 lb filled
75 gallon, 48 × 18 × 21 in67.3 US gal (255 L), heater about 225 W
20 gallon long, 30 × 12 × 12 in14 US gal (53 L), 3 bags of 20 lb gravel
Cylinder, 24 in diameter, 30 in tall52.9 US gal (200 L), 3.14 sq ft of floor
Bow-front, 48 in long, 15 in straight part, 6 in bow, 20 in tall (approximation)69.6 US gal (264 L), 6.57 sq ft of floor
40 gallon breeder with 2 in of sand instead of gravel36.5 US gal (138 L), about 75 lb of sand

Frequently asked questions

How many gallons is my aquarium?
Multiply the inside length, width and water height in inches and divide by 231 (cubic inches per US gallon). The 36 × 18 in tank above filled to 13 in of water is 36 × 18 × 13 = 8,424 cubic inches, which is 36.5 US gal (138 L). To the rim, with no gravel, the same tank holds 44.9 gallons, and its label says 40: tank labels are nominal. Imperial gallons are 4.54609 L each; the imperial figure is shown under the result.
Why is the water less than the tank’s size?
Three things take room: the gap you leave below the rim, the substrate (its depth is taken off the water height) and decor. For the 40 gallon breeder, going from 44.9 gallons to the brim to 1 in below the rim over 2 in of gravel leaves 36.5 gallons, and with no substrate it holds 42.1 US gal (159 L). The calculator does not subtract rocks or wood.
How do I measure a bow-front tank?
Measure the inside length, the depth of the straight part (front to back, without the bulge) and the bow depth (how far the front sticks out beyond the straight part). The calculator treats the bow as half an ellipse as long as the tank and as deep as the bow, so its area is π ÷ 4 × length × bow depth added to length × width. That is an approximation, since real bows are circular arcs; it is close for a gentle bow and rougher for a deep one. A 48 in tank with a 15 in straight part, a 6 in bow and 20 in of height comes to 69.6 US gal (264 L) at the default fill.
How much does a filled aquarium weigh?
Fresh water weighs 8.34 lb per US gallon and saltwater at a specific gravity of 1.025 about 8.55 lb. A 55 gallon tank (48 × 13 × 21 in outside) with 2 in of gravel holds 48.6 gal: 406 lb of fresh water plus 75 lb of gravel is about 480 lb (218 kg), and about 491 lb as a saltwater tank, before the glass, stand and equipment. The pore water in the gravel adds a little more. Use the maker's rated load for the stand, and check the floor under a large tank.
What size heater do I need for my aquarium?
A common rule of thumb is 3 to 5 watts per gallon, nearer 3 when the room is only about 10 °F cooler than the water and more as the gap grows. Fluval's E series (100 W up to 30 gal, 200 W up to 65 gal, 300 W up to 100 gal) works out to 3.0 to 3.3 W per gallon for 78 °F water in a 68 °F room. This calculator scales with the temperature rise, so the 40 gallon breeder above needs about 125 W. It is an estimate: a cold room, a draft or an outside wall calls for more, and two smaller heaters at opposite ends are safer than one big one.
What filter flow should I look for?
A typical target is 4 to 6 times the water volume per hour, so the 36 gallon tank above wants a filter rated for about 146 to 219 gal/h. Planted tanks often run lower, crowded or marine tanks higher, and the rated flow drops as the media clogs, so it is a typical figure to start from, not a standard.
How much gravel or sand do I need for my tank?
Floor area × depth gives cubic feet, and cubic feet times the bulk density gives pounds. A 36 × 18 in floor is 4.5 sq ft; 2 in of gravel is 0.75 cu ft, about 78 lb, which is 4 bags of 20 lb, and 2 in of sand is about 75 lb. The densities are planning figures (104 lb per cu ft for gravel, 100 for sand); a lighter substrate weighs less, so go by the bag label, and buy a little extra.
Does the calculator work for a cylinder?
Yes: pick Cylinder and enter the inside diameter and height. Area is π × (diameter ÷ 2)². A 24 in diameter, 30 in tall cylinder with the default fill (1 in below the rim, 2 in of gravel) holds 52.9 US gal (200 L).
Should I use inside or outside dimensions?
Inside, because the water fills the inside. Glass is typically 1/4 to 1/2 in thick (more on big tanks), so a tank measured on the outside overstates the volume by a few percent. If you only have outside sizes, take the glass thickness off each side.

Handy tools

  • Unit Converter: Convert gallons, litres and pounds, or a measurement in inches to centimetres.
  • Feet and Inches Calculator: Turn a tank measured in feet and inches (2 ft 6 in) into the total inches the length and width fields take.

Related calculators