Garage Floor Tile Calculator: How Many Interlocking Tiles Do I Need?
A 22 × 20 ft garage of 12 in interlocking tiles with ramped edges along the garage door end and one side needs 39 boxes of 12: 22 columns by 20 rows is 440 tiles, and 5% extra makes 462 garage floor tiles. Add 42 ramped edge pieces and 1 corner piece. Tiles = columns × rows, with a cut tile counted as a whole one; the edge pieces sit outside the tiles, so each ramped side takes about 2 in off the floor to be covered.
Figures based on the sources listed belowUpdated How we calculate
Buy 39 boxes. ≈ 462 garage floor tiles to buy, including the 5% extra.
Buy 39 boxes
440 sq ft + 5% waste = 462 sq ft
≈ 462 garage floor tiles to buy, including the 5% extra
- Tiles across the floor: 22 columns, by 20 rows = 440 tiles, cut tiles counted whole
- Ramped edge pieces: 42 edge pieces, often sold in packs of 10
- Corner pieces: 1 corner piece, often sold in packs of 4
How this number is calculated
440 sq ft + 5% waste = 462 sq ft ÷ 11.85 sq ft per box = 39 boxes
Shopping list
- Interlocking garage floor tiles, 12 in
- Garage floor tile edge ramps and corners
- Rubber mallet
- Utility knife with blades
- Jigsaw blades for plastic
- Concrete floor degreaser
Your project
- Garage length × garage width: 22 × 20 ft
- Tile size: 12 in square (about 30 cm)
- Ramped sides along the length: One side
- Ramped sides along the width: One side
- Edge piece depth: 2 in
- Pattern: One color
- Tiles per box: 12 tiles
- Waste: Standard: cuts and a spare or two (5%)
Also pick up
- Interlocking garage floor tiles, 12 in
- Garage floor tile edge ramps and corners
- Rubber mallet
- Utility knife with blades
- Jigsaw blades for plastic
- Concrete floor degreaser
Reopen this calculation: /calculators/garage-floor-tiles/?s=eyJyb29tIjp7Imxlbmd0aEZ0IjoyMiwid2lkdGhGdCI6MjB9LCJkZWR1Y3Rpb25zIjpbXSwid2FzdGVQY3QiOjAuMDUsInBhcmFtcyI6eyJ0aWxlU2l6ZUluIjoxMiwiY3VzdG9tVGlsZVNpemVJbiI6MjQsIm9wZW5MZW5ndGhTaWRlcyI6MSwib3BlbldpZHRoU2lkZXMiOjEsImVkZ2VEZXB0aEluIjoyLCJwYXR0ZXJuIjowLCJ0aWxlc1BlckJveCI6MTJ9fQ
Show diagram
Saved projects
No saved projects yet.
Tiles for common garages by tile size
| Garage (length × width) | Area (sq ft) | 12 in tiles | 15.75 in tiles | 18 in tiles |
|---|---|---|---|---|
| 10 × 20 ft (narrow single bay) | 200 | 200 | 128 | 98 |
| 12 × 20 ft (1-car) | 240 | 240 | 160 | 112 |
| 20 × 20 ft (2-car) | 400 | 400 | 256 | 196 |
| 22 × 24 ft (large 2-car) | 528 | 528 | 323 | 240 |
| 30 × 30 ft (3-car) | 900 | 900 | 529 | 400 |
Edge and corner pieces by ramped sides, 22 × 20 ft garage
| Ramped sides | Edge pieces | Corner pieces | Tiles in the grid |
|---|---|---|---|
| None | 0 | 0 | 440 |
| Door end only | 20 | 0 | 440 |
| Both ends | 40 | 0 | 440 |
| Door end and one side | 42 | 1 | 440 |
| Both ends and one side | 62 | 2 | 440 |
| All four sides | 84 | 4 | 440 |
Tile sizes, packs and edge pieces from the makers
| Tile | Size | Per pack | Edge and corner pieces |
|---|---|---|---|
| RaceDeck Free-Flow (12 in) | 12 × 12 × 0.5 in | 12 tiles, 12 sq ft | 1.75 × 12 in border pieces |
| Swisstrax Ribtrax Pro (40 cm) | 15.75 × 15.75 × 0.75 in | 6 tiles, 10.32 sq ft | edges 2.5 × 15.75 in, 10 per pack; corners, 4 per pack |
| Greatmats Diamond (12 in) | 12.125 × 12.125 × 0.625 in | 25 tiles, 25.5 sq ft | Click Tile ramps and a 2.4 in corner ramp |
| Technoflex TechnoLOK (18 in, PVC) | 18 × 18 in | 18 tiles, 40.5 sq ft | not listed in the sources |
| Michelin garage tile (18 in) | 18 × 18 in | 6 tiles, 13.5 sq ft | not listed in the sources |
Methodology & assumptions
Tiles are counted by rows and columns, because interlocking tiles are laid in a grid and a cut tile still costs a whole tile. Columns = the floor length in inches ÷ the tile size, rounded up; rows = the width in inches ÷ the tile size, rounded up; tiles = columns × rows. Tiles are taken as the nominal size with no joint, since interlocking tiles meet edge to edge; if a tile is a little over its nominal size (12.1 in instead of 12 in) pick Custom size. Ramped edge pieces are placed along the open sides, where a vehicle or foot meets the tiles, and they sit outside the field of tiles, so each ramped side takes the edge depth (about 2 in by default) off the dimension the tiles must cover. An edge piece is one tile long, so a ramped length side takes one per column and a ramped width side one per row. A corner piece goes where a ramped length side meets a ramped width side, so corners = ramped length sides × ramped width sides, up to 4. Edge and corner counts are exact; they are sold in packs, so round up to the pack and the spare covers a cut or a mistake. The waste percentage applies to the tiles only. 5% is a typical allowance for the cuts at walls and around posts, and 10% suits a garage with many posts, steps or a drain. These percentages are estimates, not maker figures. A checkerboard puts half the tiles in each color, rounded so that the first color has the extra one when the count is odd; a one-tile border in a second color takes the ring of tiles around the field, 2 × (rows + columns) − 4. The waste is added to each color separately and rounded up. Boxes = tiles ÷ tiles per box, rounded up; the tiles per box is the count on the box, since it varies by maker and size. Areas you will not tile, such as a workbench or a drain pad, reduce the count in proportion to the area they take, which is an estimate. A gap of about 1/4 to 1/2 in at walls and the garage door is commonly advised for expansion (check your maker’s instructions); the cut tiles make it, so it is not added to the count. Tiles are fitted dry on a clean, level slab; moisture and an uneven slab are for the maker’s instructions. The metric toggle shows the garage length and width in m.
- RaceDeck Free-Flow 12 x 12 in garage tile, 12-pack covering 12 sq ft, 0.5 in thick (Amazon product listing: SnapLock RaceDeck Free-Flow 12"x12" Garage Tiles, 12pk)
- Greatmats: RaceDeck Garage Tile Border Corner Edges 1/2 Inch x 1.75x12 Inches (border piece size)
- Swisstrax: Female Edge and Corner - PRO product pages (edge 2.5 x 15.75 x 0.75 in, corner made for 15.75 in PRO tiles)
- Obsessed Garage: Swisstrax Ribtrax PRO (6-Pack / 10.32 sq. ft.), tile 15.75 x 15.75 in (retailer listing)
- Greatmats: Click Tile Corner Ramp and Diamond garage tile, 12-1/8 in, 25-pack covering about 25.5 sq ft (Greatmats product pages and a retailer listing)
- Home Depot: Technoflex TechnoLOK Garage Floor Tile 18 in x 18 in, 18-pack, 40.5 sq ft
- Costco: Michelin Garage Flooring Tiles 18" x 18" 6-Pack, about 13.5 sq ft (retailer listing)
- Garage Journal forum thread: RaceDeck with a change in grade (RaceDeck reply on a 1/4 to 1/2 in expansion gap at walls and the garage door)
- Norsk PVC garage tiles, about 18.3 in square, 6-pack covering 13.95 sq ft (Walmart product listing)
How to calculate garage floor tiles
- Measure the garage. Measure the length and width of the floor to be tiled, and subtract any area you will leave bare.
- Count columns and rows. Divide the length and the width, each in inches, by the tile size and round up. Multiply the two numbers for the tiles; a cut tile counts as a whole one.
- Add edges and corners. Choose the sides where a car or a person steps onto the tiles. Each gets one edge piece per tile along it, and each corner where two ramped sides meet gets a corner piece.
- Add extra tiles. Add about 5% for cuts (10% for a floor with posts or a drain) and round up. For two colors, count each color separately.
- Count the boxes. Divide the tiles by the tiles in the box you are buying, round up, and add edge and corner packs.
Worked examples
| Project | Result |
|---|---|
| 22 × 20 ft garage, 12 in tiles, ramps on the door end and one side, 12 per box, 5% extra | 440 tiles + 5% → 39 boxes, 462 garage floor tiles, 42 edges, 1 corner |
| The same garage with 10% extra for posts and a drain | 440 tiles + 10% → 41 boxes, 484 garage floor tiles |
| The same garage in 15.75 in (40 cm) tiles, 6 per box | 272 tiles + 5% → 48 boxes, 286 garage floor tiles, 33 edges |
| The same garage in 18 in tiles, 6 per box | 210 tiles + 5% → 37 boxes, 221 garage floor tiles, 29 edges |
| The same garage as a two-color checkerboard (12 in tiles) | 440 tiles + 5% → 39 boxes, 462 garage floor tiles, 231 of each color |
| The same garage with a one-tile border in a second color | 440 tiles + 5% → 39 boxes, 462 garage floor tiles, 84 in the border color |
| 30 × 30 ft 3-car garage, 12 in tiles, ramp on the door end only | 900 tiles + 5% → 79 boxes, 945 garage floor tiles, 30 edges |
Frequently asked questions
- How many garage floor tiles do I need?
- Divide each side in inches by the tile size and round up to get columns and rows, then multiply. A 22 × 20 ft garage of 12 in tiles is 22 columns by 20 rows, 440 tiles. A cut tile at the far wall is still a whole tile bought, so rounding up is right. Add about 5% for cuts, which makes 462, and divide by the tiles per box (12 for many 12 in tiles) to get 39 boxes.
- How many edge and corner pieces do I need?
- Ramped edge pieces go along each side where you drive or walk onto the tiles, typically the garage door end and any side door. An edge piece is about one tile long, so a side takes one per tile along it. A corner piece goes where two ramped sides meet at a right angle. This garage, ramped on the door end and one long side, needs 42 edge pieces and 1 corner. Ramped on the door end alone it needs 20 edges and no corner; ramped on all four sides, 84 edges and 4 corners. Edges are often sold in packs of 10 and corners in packs of 4, so round up to the pack.
- Do the edge pieces replace tiles?
- No: the edge ramps are extra pieces added outside the field of tiles, about 1.75 to 2.5 in deep depending on the maker, so they do not replace a row. They do mean the tiles need to cover a little less floor, which the calculator allows for with the edge piece depth. It rarely changes the count by more than a row or a column, and not at all when the floor is just over a whole number of tiles.
- Which tile size should I choose, 12 in, 15.75 in or 18 in?
- A bigger tile means fewer pieces and fewer joints, but the number of boxes depends on how many tiles come in a box. For the 22 × 20 ft example: 440 tiles of 12 in, 272 of 15.75 in (40 cm) and 210 of 18 in before waste. The coverage in each tile counts too: 15.75 in is 1.72 sq ft a tile, against 1 sq ft for 12 in and 2.25 sq ft for 18 in. Choose by the product you like and its edge pieces; edge and corner pieces are made for one line, so they are not interchangeable between makers.
- How do I count a checkerboard or border pattern?
- For a checkerboard, half the tiles go in each color: the 440 tiles of the example are 220 of each, 231 of each with 5% extra. For a one-tile border, the outer ring of the field is the second color, 2 × (rows + columns) − 4 = 80 tiles, leaving 360 in the main color; with 5% extra that is 378 and 84. Each color is rounded up separately, so the total can be a tile or two over the single-color count. Choose the pattern in the calculator and it lists the colors.
- How much extra should I buy?
- About 5% is a typical allowance when the cuts are at the walls, and 10% when there are posts, steps or a floor drain to cut around; both are estimates, not maker figures. On the example garage, 10% makes 484 tiles and 41 boxes against 462 and 39 at 5%. Keep a few spare tiles from the same lot, since colors can differ a little between production runs.
- Do I leave a gap at the walls?
- A gap of about 1/4 to 1/2 in at walls and at the garage door is commonly advised, since plastic tiles expand and shrink with temperature; a RaceDeck reply quoted in a Garage Journal forum thread gives this range, and your maker’s instructions come first. The gap is made by cutting the last tile a little short, so it does not change the tile count.
- What is the difference between this and the tile calculator?
- The tile calculator works from the area of a room and a box coverage, which suits ceramic and stone. Interlocking garage tiles are laid in a grid, with edge ramps and corners that ceramic does not have, so this one counts rows and columns and the edge and corner pieces too. For a floor that gets a coating instead, use the epoxy floor calculator.
Handy tools
- Feet and Inches Calculator: Turn a tape reading in feet, inches and fractions into the decimal feet the length and width fields take.