Skip to main content
ponderloop

Kitchen Cabinet Paint Calculator

A kitchen with 16 doors (15 × 30 in, both faces), 8 drawer fronts (18 × 6 in) and 18 ft of cabinets at 5 ft average height has about 133 sq ft to finish per coat (100 sq ft of doors, 6 of drawer fronts and 27 of face frame). With 10% waste, two coats of Benjamin Moore Advance (400 sq ft per gallon) take 1 gallon (0.73 gal, so 3 quarts if you buy by the can), and one coat of Zinsser B-I-N Advanced Synthetic Shellac primer (300 sq ft per gallon) takes 2 quarts.

Figures based on the sources listed belowUpdated How we calculate

Waste

Count every door, including the small ones above the fridge.

The average width of one door. Doors vary, so use a typical size.

The average height of one door (wall cabinet doors are often 30 in, base cabinet doors 24 to 30 in).
Painting both faces keeps the door from warping unevenly and makes the back match. Pick front only if the backs stay as they are. Drawer fronts are counted on one face.

An estimate: the part of the cabinet front that is face frame or box rather than door. Doors cover the rest, so the full run times height is not painted. About 25 to 35% is typical; enter 0 if you are only painting doors and drawer fronts.

One coat of bonding primer is normal on sanded cabinets. Enter 0 to skip primer.
Coverage is per coat. Zinsser lists 300 to 400 sq ft per gallon for the Advanced Synthetic shellac primer (the low end is used) and about 500 for the shellac-base primer.

Two finish coats is standard for cabinets. A big color change can need three.
Coverage is per coat, at the low end of the manufacturer range (Advance 400 to 450, Emerald Urethane Trim Enamel 350 to 400, Cabinet Coat 350 to 450 sq ft per gallon).

Buy 1 gallon.

Buy 1 gallon

133 sq ft + 10% waste = 146.30 sq ft

  • Paint by the can (Benjamin Moore Advance, 2 coats): 3 quarts, about 0.73 gal
  • Primer by the can (B-I-N Advanced Synthetic Shellac, 1 coat): 2 quarts, about 0.49 gal
  • Doors (faces entered, one coat): 100 sq ft
  • Drawer fronts (one coat): 6 sq ft
  • Face frames and exposed box (estimate, one coat): 27 sq ft
  • Pieces to paint: 24 doors and drawer fronts

Low

$50.00

Expected

$75.00

High

$110.00

Includes 13.30 sq ft waste

How this number is calculated

133 sq ft + 10% waste = 146.30 sq ft ÷ 200 sq ft per gallon = 1 gallon

Shopping list

  • Cabinet and trim enamel (quart)
  • Bonding primer (quart)
  • Liquid deglosser
  • Fine foam rollers (4 in)
  • Angled sash brush (2 in)
  • Sanding sponges, 220 grit
  • Cabinet degreaser
  • Painters tape
Show diagram

Saved projects

No saved projects yet.

Coverage rates used for each product

Per coat, in square feet per gallon. "Used" is the low end of the data sheet range; paint amounts are two coats and primer is one coat, each with 10% waste, for 100, 200 and 300 sq ft of surface per coat, worked by this calculator.
PaintData sheetUsed100 sq ft, 2 coats200 sq ft, 2 coats300 sq ft, 2 coats
Benjamin Moore Advance400 to 450 sq ft/gal4003 quarts1 gallon + 1 quart1 gallon + 3 quarts
Emerald Urethane Trim Enamel350 to 400 sq ft/gal3503 quarts1 gallon + 2 quarts2 gallons
Insl-x Cabinet Coat350 to 450 sq ft/gal3503 quarts1 gallon + 2 quarts2 gallons
cabinet enameltypical sq ft/gal3503 quarts1 gallon + 2 quarts2 gallons

Primer coverage and amounts

One coat with 10% waste, for 100, 200 and 300 sq ft of surface, worked by this calculator.
PrimerData sheetUsed100 sq ft200 sq ft300 sq ft
B-I-N Advanced Synthetic Shellac300 to 400 sq ft/gal3002 quarts3 quarts1 gallon + 1 quart
B-I-N Shellac-Baseabout 500, practical sq ft/gal5001 quart2 quarts3 quarts
primertypical sq ft/gal2502 quarts1 gallon1 gallon + 2 quarts

Paint and primer for a typical kitchen

Doors 15 × 30 in with both faces, drawer fronts 18 × 6 in, 5 ft average height, 30% face frame, 10% waste. Paint is two coats of Benjamin Moore Advance; primer is one coat of B-I-N Advanced Synthetic Shellac. Worked by this calculator.
KitchenSq ft per coatPaintPrimer
Small galley (10 ft of cabinets, 10 doors, 4 drawers)812 quarts2 quarts
Average kitchen (18 ft of cabinets, 16 doors, 8 drawers)1333 quarts2 quarts
Large kitchen with island (30 ft of cabinets, 26 doors, 12 drawers)2171 gallon + 1 quart1 gallon

Cabinet prep steps before paint

General practice and estimates; follow the preparation section of the data sheet for your products.
StepWhat to doNote
Remove and labelTake off doors, drawer fronts and hardwareNumber each door and its opening so they go back where they came from
DegreaseWash with a degreasing cleaner, rinse, let dryKitchen grease stops paint and primer from bonding
Sand or deglosserScuff glossy factory finish with 150 to 220 grit, or wipe with a liquid deglosserEstimate: the goal is a dull surface, not bare wood
Fill and sand smoothFill dents and old hardware holes, sand flush, wipe off dustDust left behind shows in a glossy cabinet finish
PrimeOne coat of bonding or stain-blocking primerNeeded on bare wood, stains and tannin-rich wood such as oak or cherry
PaintTwo thin coats, light sanding with fine paper between coats if the data sheet allows itCabinet enamels cure slowly: go easy on doors and drawers for a couple of weeks

Methodology & assumptions

The area to finish, per coat, is the doors (width × height × 1 or 2 faces), plus the drawer fronts (one face), plus the face frame: cabinet run × average cabinet height × the share of the front that is frame and exposed box, 30% by default. That share is an estimate, because the doors already cover the rest of the front; enter 0 to paint doors and drawer fronts only. Door and drawer-front edges are not added: at 3/4 in thick they come to about 5% of a door's area, which the 10% waste option absorbs. Paint is the area with waste × coats ÷ the coverage per gallon of the paint you pick; primer is the same with its own coats and coverage. The big number is whole gallons of paint, rounded up. The "by the can" lines instead buy whole gallons first and round the remainder up to quarts (4 quarts to a gallon), which is how most people shop: for the example that is 3 quarts of paint, not a second full gallon. Coverage is the per-coat figure on each manufacturer's data sheet, taken at the low end of the range (Benjamin Moore Advance 400 to 450, Sherwin-Williams Emerald Urethane Trim Enamel 350 to 400, Insl-x Cabinet Coat 350 to 450, Zinsser B-I-N Advanced Synthetic Shellac 300 to 400 sq ft per gallon; about 500 for B-I-N Shellac-Base). Data sheet coverage is at a stated film thickness on a smooth surface and does not allow for spray or roller loss, so the low end is the safer planning number. The "other" rows use 350 for paint and 250 for primer, the same figures as the room paint and primer calculators on this site. Lengths and door sizes switch to metric; paint and primer stay in US gallons and quarts, the sizes the cans are sold in.

How to calculate how much paint and primer you need for kitchen cabinets

  1. Count doors and drawer fronts. Count every door and drawer front, and measure a typical door and drawer front in inches.
  2. Choose faces. Decide whether you will paint both faces of the doors. Drawer fronts count one face.
  3. Add the face frames. Enter the total length of the cabinet run and the average height; about 30% of that area is frame and exposed box.
  4. Pick your products and coats. Choose the paint and primer, or the generic rates, and set coats: usually one of primer and two of paint.
  5. Buy by the can. Read the paint and primer amounts: whole gallons plus the remainder in quarts. Buy it all together, add a quart for touch-ups, and prep the surface before painting.

Worked examples

ProjectResult
16 doors (15 × 30 in, both faces), 8 drawer fronts, 18 ft run at 5 ft, 2 coats Advance, 1 coat B-I-N Advanced Synthetic1 gallon of paint (3 quarts by the can), 2 quarts of primer, 133 sq ft per coat
Galley kitchen: 10 doors, 4 drawer fronts, 10 ft run at 5 ft1 gallon of paint (2 quarts by the can), 2 quarts of primer, 81 sq ft per coat
Large kitchen with island: 28 doors (fronts only), 14 drawer fronts, 32 ft run, 3 coats Emerald Urethane Trim Enamel2 gallons of paint (1 gallon + 2 quarts by the can), 3 quarts of primer, 146 sq ft per coat
Doors and drawer fronts only: 20 doors (14 × 28 in, both faces), 6 drawer fronts (15 × 7 in), Cabinet Coat, B-I-N Shellac-Base1 gallon of paint (3 quarts by the can), 1 quart of primer, 113 sq ft per coat

Frequently asked questions

How much paint do I need to paint kitchen cabinets?
Add up the area of the doors (both faces if you paint the backs), the drawer fronts and the face frames, add 10% for waste, multiply by the number of coats and divide by the paint's coverage per gallon. The example kitchen is about 133 sq ft per coat, so two coats of a paint that covers 400 sq ft per gallon takes 0.73 gallons: 3 quarts. An average kitchen usually needs 1 to 2 gallons, and a small one fits in 2 or 3 quarts.
What coverage should I use for cabinet paint?
Use the per-coat coverage on the data sheet of the paint you are buying, at the low end of the range. The sheets list 400 to 450 sq ft per gallon for Benjamin Moore Advance, 350 to 400 for Sherwin-Williams Emerald Urethane Trim Enamel and 350 to 450 for Insl-x Cabinet Coat. Those figures assume a smooth surface at the recommended film thickness, and cabinet doors lose paint to edges, panels and roller or sprayer loss, so planning on the low end is safer. This calculator does that automatically.
Do I need to paint both sides of cabinet doors?
Most painters finish both faces so the door takes moisture evenly from both sides and the back matches the front. Painting only the front is common when the backs are laminate or already finished. Choose either in the calculator; doubling the faces roughly doubles the door area.
How much primer do I need for cabinets?
Usually one coat. The example kitchen is 146 sq ft with waste, so one coat of a primer that covers 300 sq ft per gallon takes 0.49 gallons, which is 2 quarts. Zinsser lists 300 to 400 sq ft per gallon for B-I-N Advanced Synthetic Shellac and about 500 for B-I-N Shellac-Base; the calculator uses the low end of the Advanced Synthetic range. Raw or very porous wood can drink more primer than the data sheet figure, so add a second coat or a few extra ounces if the first one soaks in.
Should I sand or use a deglosser before painting cabinets?
You need to dull the factory finish one way or the other. A light scuff with 150 to 220 grit paper or a sanding sponge is the usual method; a liquid deglosser is a lower-dust alternative. Degrease first, because paint will not bond to kitchen grease, and wipe off all dust afterwards. This is general practice and an estimate of the right grit: your primer's data sheet may call for a specific prep, such as sanding to bare wood for some products, and it wins.
How many coats of paint do cabinets need?
Two finish coats over one coat of primer is the usual recipe, and it is the calculator's default. A big change, such as dark to white, can need a third. Each extra coat adds about the same amount of paint again: the example takes 0.73 gallons for two coats and about 1.1 for three.
Is this the same coverage as the room paint and primer calculators?
The "other" options use the same figures: 350 sq ft per gallon per coat for paint and 250 for primer. The named cabinet products use their own data sheet rates, which are higher for Advance and for the shellac primers, so they need a little less than a wall-paint estimate would for the same area.
Should I buy quarts or a gallon?
The headline counts gallons, rounded up. The "by the can" lines show the cheaper split: whole gallons first, then the rest in quarts. For the example that is 3 quarts of paint rather than a full gallon. Paint is also tinted per can, so buy all you need at once from the same batch, and add a quart of leftover for touch-ups if the color is custom.
Is spraying cabinets different?
Spraying lays down a thinner, smoother film, but overspray and cup cleanup waste more paint than rolling, and the data sheet rate assumes no loss. Plan on the low-end coverage this calculator uses, and add the 10% waste option. Thinning and tip size are on the paint's data sheet.

Related calculators